Aerofoam T-45 Turbine Setup and Maiden

Sixth Sense Aviation
1 follower
1 Video View·Nov 15, 2025
Aerofoam T-45 setup and maiden. Sharing some experiences with the aircraft, the plane has over 65 flights now as of the date of this video.
Hello everyone, Paul ZRC coming to you from my garage in Texas. Today we're going to talk about
the Aerophone T45 Goshawk turbine version. I'll go over the journey I went through setting it up,
how I configured it, and at this stage the airplane has about four hours of flight time on it.
I've had a lot of flights, I love it, and I will tell you about the final settings I ended up using
and hopefully this will be very helpful when you set up your airplane.
Let's start with component layout and CG. So as you see this is the layout I have. I, under this
board here, have the UAT, fuel pump, and all the plumbing components are really there. You see I'm
using the two tanks for flight. I don't have smoke. I fill up all the way up to about halfway on the
second tank and I get nice about seven and a half minutes of flight. Okay, component layouts and CG.
I made the plane this way. As you see I have the turbine battery and the two flight batteries as
far back as I could get them. This is my HSD Jet's flight controller that I love to use,
but in general the plane flew really well like this. I didn't put any batteries here in the nose.
I felt it was way too nose heavy and for maiden I recommend starting this way. Put all your weight
back as far as you can and it flew well. I did later with more flights, I did take some
weight out of the nose and I'll show you how I did that. Again, that's a personal preference. The
plane flies really well configured this way, but I still wanted to take some, move the CG
back a little bit for landings and I took some weight out of the nose. You can see where I removed
the nose weight. If you gently cut the plastic cone off, right behind it is that piece of
cylindrical metal weight you can take out. I took that out. There's one still further in the nose,
but so there's two of them. Just taking this one out really helped with landings and a little bit
more neutral pitch stability during rolls and flying inverted. So to complete the CG setting,
I have this piece of nose out and all the batteries as far back as possible. All right, let's move on
to surface throws, where I ended up with everything. So just kind of walk you through that.
So on ailerons, I'm holding this here. So this is about 30 millimeters each way,
gives you a nice roll rate. On flaps, mid flaps, I have at about 25 and then full flaps quite a bit
more, 45 millimeters, let's say. Sorry, just holding this with my hand here. Notice I am not using
the leading edge slats at all. I actually glued them shut. I like the flight envelope during
landing better. One warning, the plane does shift CG quite a bit when you drop flaps. The CG shifts
and the plane tends to nose down. So what I ended up with, and I did this in flight, is you notice my
elevator with mid flaps, it drops just a little bit. I don't know if I can measure that, but I can
show you here on the video. This looks like just a few millimeters and a little bit more with landing
flaps. So that keeps the nose, the pitch level and the plane won't stall on you for landings.
The flaps do have an effect of raising the nose up. I think with the slats coming down at the same
time, that helps a little bit. I chose not to fly with the slats. I've had the EDF version,
I tried that and I didn't like how it behaved. So I didn't do that in this one. On the rudder,
I have quite a bit of rudder. I don't use it all the time, but it works for landings.
So let's see if I can do this here.
Yeah, it's over 30 millimeters. Thank you. Yeah, about 35 millimeters each way.
It helps for landings, crosswinds to help just crab it. So that's my setup and this has been a
great journey with this plane. You'll see a maiden video and some other additional tweaks I did,
but really this is it. It's straight out of the box how it comes. I bought mine in Banana Hobby.
Thank you for them. They have been great in quick delivery and support. Maybe we can show the engine
compartment, how I set up. I have the Swiwin 80, which I also bought from Banana Hobby. I have
three screws on each side holding it and that gives it a nice, you know, the 25 millimeter
gap between the end of the exhaust from the turbine and where the intake bell of the
thrust tube begins. So it works great and everything's up. Again, I have four hours,
over four hours of flight time on the airplane and it's been a great flight.
so I can extend the flight time by another minute probably. Awesome.
You weren't full throttle very much, were you? No. Okay, yeah, that's a good point. So you know
it's six minutes, but I'm not going to fuel fill up this one past half.
