The Mauser Karabiner 98k began production as an excellent quality rifle, with every nuance of fine fit and finish one would have expected form the Mauser company. World War Two had barely begun by the time a few compromises began to be made to maintain production, however - and by the end of the war the K98k was a mere shadow or its former self. As with the similar deterioration in quality with Japanese Arisaka rifles, the critical mechanical elements of the K98k were just as safe and functional at the very end as the were at the beginning - but the ancillary aspects came crashing down. One might argue that these changes should have been made from the beginning; that issuing an infantry rifle made to the same finish as a fine commercial sporting arm is a silly waste of resource.
Hi guys, thanks for tuning in to another video on ForgottenWeapons.com.
I'm Ian McCollum, and I'm here today at the Rock Island Auction Company
taking a look at a trio of Mauser K98k rifles
that are going to be for sale in their upcoming December of 2018 auction.
And I picked out these three because I think they do really a quite nice job
of illustrating the change in the actual production quality
of the Mauser 98k over the course of World War Two.
If you think about, like, last-ditch, poorly made, you know, substitute rifles,
what most people think about are Type 99 Arisakas.
We all know about the Japanese going from this really awesome, super fancy rifle
down to this really very crude last-ditch thing.
Well, the truth of the matter is the Germans did pretty much the same thing.
And we're going to take a look at that today, starting with an S42G marked rifle,
which is one of the German secret code designations that indicates a 1935 production rifle,
when they were still trying to hide their rearmament from the Allies.
So we have this, we have a 1944 production gun, and then we have a Kriegsmodell,
a 1945 production gun that really is scraping the bottom of the barrel
as far as K98 production goes.
So, let's dig right into this and see what happened to German production during the war.
Alright, so I'm going to give you a quick introduction to each rifle individually,
and then we're going to go through each feature of the guns,
and look at all three, early, middle, and late, side by side,
so you can see how each feature changed.
We'll start with this guy. This is an S-42G.
And S-42 was one of the very early codes for Mauser.
Of course, they would use codes instead of actual manufacturer names throughout the war,
with the exception of BSW, just as a way to try and obfuscate
where the guns were being made and how many were being made.
So in this case S-42 is Mauser, and then G indicates 1935.
So this is really like the second year of actual Kar98k production.
Notice that this is early enough that it doesn't actually have Waffenamts,
it has German commercial type proof marks on it.
So no swastikas anywhere can be found on a rifle this early.
Our mid-war gun here is a BCD, and that is Gustloffwerke.
And this is a 1944 production gun.
A lot of these markings are standardised, except they vary quite a bit.
And the 1944 BCDs are one example where they only used the second digit of the year.
So this is 1944.
And this one is a pretty good example of a point at which some changes are starting to be made,
but we're not really in full Kriegsmodell panic mode yet.
And then this guy is full Kriegsmodell panic mode.
The, you know what, has hit the fan at this point.
This gun is code marked BYF, which is Mauser.
Mauser went through a bunch of different codes through the course of the war.
And this is a 1945 dated gun.
You'll notice that the stock on this thing isn't even finished, it's just plain raw wood.
Anyway, let's get on to the specific features.
There are a few things here that may actually be a little bit counterintuitive.
So you'll notice that the mid and the late war guns both have these sheet metal front sight hoods,
where the early gun ... does not have one.
And the early guns actually don't even have the little rails, or the little notches,
to use the front sight protector.
And the reason for that is very early on they actually issued a separate sheet metal muzzle cap.
It was a protector, it covered the front sight.
The problem was it was detachable, it ... wasn't permanently connected to the rifle in any way,
so it could get lost.
It was found that it would be a much more effective solution
to just put a permanent front sight hood on the guns.
So this is a change that was made not to ease production,
but actually to make the rifle a little bit better in the very early years.
And we'll see one more example of that on the very other end of the rifle.
But before we get that far, let's consider a couple other elements here.
We have cleaning rods and bayonet lugs on the early and middle term guns.
None on the Kriegsmodell.
By the end of the war it's like the cleaning rods, like,
you know what, your expected survival period in combat against the Russians and the Americans
is probably shorter than the time period in which you're likely to have to clean the rifle.
So we'll just leave that off entirely.
That way they didn't have to drill the hole, didn't have to make the cleaning rods, none of that.
And the same goes for the bayonet lug.
By the end of the war people finally realised that, look,
sticking this short little knife bayonet on the end of the rifle
is not actually practical for anything.
So just forget it, leave them off.
As for the early and mid-term guns, these features didn't change.
You, well, went from in the white to blue, but that's it.
Staying here at the muzzle end of the gun, we can take a look at the nose caps,
which also changed rather substantially.
The very earliest guns have this very finely finished H-shaped sort of nose cap.
You know, we remove a little bit of material to remove weight,
polish it up very nicely, serialise it.
That's all fine and good until time starts to actually be, like, important in making these guns.
And by the midpoint of the war they had really very much simplified that nose cap.
So there's no reason to be cutting these, you know, ... curved H-shaped weight relief things,
you know, forget it.
Just make it solid, stamp on the serial number, and we're good to go.
By the end of the war we don't even have time to deal with milling the thing, heck.
Just stamp it out, bend it around, weld it together kind of crudely there.
And by the way, you know, you've got these nice fancy spring-loaded retaining bands,
forget it.
Stick a little wood screw in there, that'll hold it in place, good to go.
We can see a similar progression in the barrel band.
Here at the beginning, well before the war even on this one,
we have this nice single piece milled barrel band.
That survives for a while, but it gets simplified.
So that you can see that the profile here gets a little bit less complex,
a little bit finely contoured.
We'll simplify.
And then once again by the end of the war it's all hands on deck,
can't even bother with milling, we'll stamp it.
Note that the inside of the sling loop here is a second stamped piece of metal,
rolled inside it.
And once again the main component is stamped, bent, crudely welded together at the side,
and held in place by another little wood screw.
Now if we take a moment at the midpoint of the rifles to take a look at the wood stocks,
we'll see some more changes.
So pre-war they were using very nice solid walnut for the stocks.
That's great.
It's strong, it's available, it looks really nice.
The problem is it has to be cured.
So if you're going to make a million K98k rifles,
you have to cut down a crap load of walnut trees,
and then you have to let that wood season.
Like it has to dry out before you can actually carve it into shape and use it effectively.
So it actually didn't take all that long.
By the time the war had just barely begun,
Germany had run out of cured, ready-to-use wooden stock blanks for the K98k.
And at that point they had to make a substitution.
And what they did was go to laminate wood, aka plywood.
If we look up close here, you can see all the little layers of wood in there.
Now this was a simplification made necessary, or a change,
made necessary by the rate of production that they were trying to achieve.
But this actually, despite not looking nearly as nice, this isn't a sacrifice in any way.
This laminate wood is actually stronger than the walnut,
and it doesn't require any curing time.
You can build these stocks, assemble them together, glue them together,
and they're ready to go.
So arguably this is one of those things that maybe they should have started with,
because it's stronger and it's quicker.
That laminate stock usage would continue all the way to the very end of the war,
although this one has a stock that hasn't even been finished.
It's just raw wood.
Moving along, we can take a look at the trigger guards and magazine floor plates.
These of course start, as with everything, quite nice.
We have a milled trigger guard here.
We have a milled magazine floor plate.
Note that we have a screw back here holding it in place.
And then this fancy second locking screw to make sure that this screw doesn't come loose.
Ooh la la, how very high quality.
Mid-war, still not bad.
We still have a milled floor plate.
We've still got this secondary locking screw, even in 1944.
But some accommodation has had to be made,
and we now have a stamped intersection here on the trigger guard.
So the trigger guard itself has gone from being milled
to being assembled from a couple stamped components,
even though the magazine floor plate is still milled.
And then of course by 45, dear Lord, the Russians are coming.
Just, for whatever it takes, make more rifles.
We now have a stamped floor plate to go along with the stamped trigger guard.
The secondary locking screws, that crap's long gone.
Like forget it, just put in a screw, tighten it down, it'll be fine.
What we don't see changing here is anything substantial
in the actual receiver, or bolt, or barrel of the gun.
These parts had to be made, of course, to a certain standard
to be safe, and accurate, and functional.
And those elements were not sacrificed at any point during the war.
So even when we got beyond the Kriegsmodell
into some of the really last-ditch Volkssturm rifles,
even then the lock-up was safe, the locking lugs were well made,
properly heat-treated, the barrels were good, the guns would be accurate.
Maybe they had to counter-bore them to make them accurate,
but the guns would shoot safely.
No nation, Germany, Japan, or anybody else,
is going to actually issue rifles that are legitimately unsafe to their soldiers.
Like, that is so counterproductive that nobody's going to do it.
We have one small change to point out in the rear sights.
And this is truly an example of some kind of goofy levels of production.
Finesse at the beginning of the war.
Before the war, the underside of the rear sight had the range markings on it,
just like the top side.
And this isn't even one of those sights that, like, there's a reason to stand up.
You know, this can make sense if you have a second sighting aperture back here,
and you stand the sight up for the pointlessly long range settings.
But on the K98k, all of your settings are done just like this.
You never are going to look at the bottom,
and yet they engrave range markings on here just as nicely as they had done on the top.
It should, of course, come as no surprise that it didn't take long
for someone to point out how stupid that was.
And those things are long gone by the middle of the war.
Even by the very end, though, the sight had not degraded any further.
You might think that they would stop bothering to mark the sight out to 2,000 metres by 1945,
but no, this is exactly the same as it was partway through the war.
And with the exception of the excessive markings on the bottom,
this is the same as the pre-war guns.
And now we have reached the buttstocks.
And there are two things to look at here.
One is the disassembly disc, and the other is the butt plate itself.
So we'll start with the disassembly disc.
Early on this is a nice milled part, you know, both sides through the stock.
And by the way, this is here because when you disassemble the K98k bolt,
the Mauser 98 bolt in general,
you want to press the firing pin down against a surface to relieve firing pin spring pressure.
And ... you don't want to damage the tip of the firing pin itself.
So this is put in there as a place where you can put the firing pin in the centre,
press the bolt down against this to compress the spring and take it apart.
So it's a nice handy little tool to have.
However, it doesn't necessarily need to be finely milled.
And by the middle of the war they had simplified it, so it's still there.
But now it's a pair of stamped pieces that are connected by a hollow rivet
through the centre to hold them in place.
Still works just the same though.
By the end of the war, maybe you saw this coming,
they were trying to cut production time anywhere they could.
And the idea of both drilling a hole in the stock,
and then making a three-part stamped assembly to go on top of it.
Well, maybe we can do something simpler.
Maybe we can just drill a hole straight through both the butt plate
and the back of the stock, right here at the toe.
And you know what? That'll work just fine.
You can cram the firing pin into that for disassembly
if you're going to live long enough to need to disassemble your bolt for some reason.
And now the one last bit is something I mentioned at the very beginning.
I said that there was a change that was made early in the war
that was actually an improvement, not a sacrifice.
And that's the butt plate.
You might look at this and figure, well, this had to be early,
and they went to a flat butt plate because it was less material.
It's actually the other way around.
The K98k design actually started with this nice flat butt plate.
So you've got a nice diagonal screw up there.
And the problem was they found that this didn't do all that good of a job
of protecting the stock.
So because it's flush with the edge of the stock here,
you leave open the opportunity for chips and scuffs,
and you can damage this fairly easily.
So early on, before there was any need to do so
from a materials or a working time point of view,
early on they changed this to a cupped butt plate
that actually encompasses the entire bottom of the stock.
And they did that because this is going to do a much better job of protecting the stock.
You can see down here at the toe,
you're not going to make a chip in the bottom
that's going to turn into a crack that runs up the length of the stock.
So this was a product improvement that happened to take place at the same time
that they were also starting to look for simplifications.
And with the exception of the change in the disassembly hole,
by the very end of the war they were still going with this same cupped butt plate.
This was something that could be stamped out,
and they didn't find any further room to simplify that.
You know, a lot of people would argue that they should have gone straight
to this thing in the very beginning.
That the idea of equipping your infantry with a rifle
that has all of the fit and finish of a fine commercial sporting rifle
is kind of a foolish waste of resources.
And there's some validity to that.
It's like, you know, did they ever really need the sight gradations
on the bottom of the sight, really?
Do you have to have these finely milled and polished barrel fittings?
Is there anything that this fancy version actually does better
than the last-ditch Kriegsmodel?
Well, not really.
I suppose there is a morale element to what you're equipping the troops with.
If they see at the very beginning of the war
that they've got some really crummy looking gun,
yeah, it may give the impression that the country is just not up to snuff
and can't handle it, can't manage to get any good weapons production.
Where you give them something fine and fancy and very expensive,
it gives you some pride and some expectation in, you know,
if they're able to make you this for a rifle,
well, the air support and the artillery support must be great.
Ultimately, the Kriegsmodel worked just as well as the standard 98k in the field.
Of course, changes like this aren't going to affect the course of the war.
It wasn't like ... reducing to this standard at the beginning
would have allowed them to make just enough more rifles
that Germany could have won World War Two.
Yeah, that never would have had any possibility of happening.
But, of course, it is primarily interesting here
just to take a look at what did happen during the course of the war.
Hopefully you guys enjoyed the video, learned something about the K98k today.
If you would like to add any one of these three to your own collection,
they're all very nice K98k examples,
and they are all coming up for sale here at Rock Island.
If you take a look at the description text below,
you'll find a link to ForgottenWeapons.com,
and from there you'll find follow-up links to each of the three catalogue pages
Rock Island has for these three rifles.
And if you want to poke around in their catalogue,
they have a bunch of other K98ks as well,
including a whole lot of snipers this time.
So, anyway, thank you very much for watching.