Part 2 تجيمع محرك سكودا 3 سلندر The second part is the assembly of the Skoda 3-cylinder 1.2 engine

KasemAutoservice
15 followers
#معلومات #مفيدة_وهامة
(الجزء الثاني) تجيمع محرك سكودا 3 سلندر بنزين 1.2
The second part is the assembly of the Skoda 3-cylinder 1.2 engine
#KasemAutoservice #skoda #cylinder #engine #auto #assembly #auto #engine #mechanisch #mechanical #timing #bmw #mekanik #maintenance #ford #mercedes
As we said in the previous video, the word Juan Colas comes with a paper.
This paper is written on it how to tighten the nut and how to tighten the spring.
Now in the video I will explain to you. I made a previous explanation, I will make a second explanation.
Of course, every engine brake has a nut.
We are forced to get a nut and not install the old one.
Because it has a nut.
Of course, we found the nut.
And this is the paper.
The paper of the Juan Colas spring.
I will explain to you.
The paper here is written on it.
You have to tighten the first spring 30 Nm.
Then tighten the next 90 Nm.
Of course, for the 740 KV, 3 cylinders, 1.2 engine, for the Polo, Fabia, and for the Mustard.
Okay?
Yes, I will explain.
Of course, this paper comes with all the Juan Colas in it.
I will explain.
Of course, now after we tighten them 30 Nm.
As it is written here.
Okay?
We have to tighten the next 90 Nm.
90 degrees.
Okay?
Now I will explain to you how to tighten 90 degrees.
I made more than one video explaining how to tighten 90 degrees.
I will make a second explanation.
Sorry.
There is a little mess with the number.
Look at this.
We will make a number of these.
We have here.
Let me put the tray.
For example.
If we make 90, it will be 360.
For example.
This is it.
Okay?
Here comes zero.
As we said yesterday in another video.
The same is 360.
Okay?
Half 360 divided by 2.
Here you have 180.
Okay, guys?
We will tighten the 90 degree.
Half 180 divided by 90.
Right?
Or am I wrong?
We tighten here 90.
Okay, guys?
The easiest way.
For example, this is the time of the house.
We have here 12 o'clock.
3 o'clock.
6 o'clock.
9 o'clock.
Okay?
If we have this degree.
We put the key.
Okay?
We tighten this at 3 o'clock.
So it became 90 degrees.
Is it clear, guys?
Okay?
Here.
This is the first degree we tighten.
As it is written in the catalog.
For example, here we consider 12 o'clock.
Okay?
We put the key like this.
We tighten it to 90.
In this direction.
If you have here.
It became 90.
Okay, guys?
We put the key from here to here.
It became 90.
If we continue it down.
It became 180.
Okay, guys?
If we continue it up.
It became 360 degrees.
We tighten it to 90.
As it is written in the catalog.
Okay, guys?
Now we will do it in a practical way.
Okay, guys?
Of course, the key does not have a job.
It does not matter how high it is.
The important thing is to tighten 90 degrees.
We try the first degree.
Now here.
We start with the first degree here.
First.
Second.
Third.
Fourth.
Fifth.
Sixth.
Seventh.
We come in the same order.
We put them here.
We go.
We start from here.
Here, as we said.
Twelve.
Now it became.
As we said.
Ninety.
We go back to the next degree.
Also in the same direction.
As we said.
A little bit.
We tighten it again.
We open it.
So that it is clear.
Then we put here.
Twelve.
As we said.
A little bit.
Here too.
It will be.
Six o'clock.
Three o'clock.
We put the key.
OK.
We come to the third degree.
The third is directly opposite.
Here.
OK.
Fourth.
OK.
Then we come to the 5th, then we come to the 6th, then to the 7th, and the last one to the 2nd.
That's it.
Now we have finished the first set.
We have finished the first set of 30, and now we have finished the 90.
We have to rest for 10 minutes.
Of course, before we tighten the last set at the end,
There is a guy who asked me, when you want to install a collage,
Look here, this paper comes with a very useful collage.
He tells you here, it must be clean under the collage, and you should not put oil on it at all.
The guy told me I have to put oil on it before installing the collage.
I have to put oil on the collage before installing it.
No, it is not possible.
This is one.
The second point, the lathe that you want to install, it is not possible to put oil on it.
The inner one, not the outer one.
I don't care about the outer one, it will have a small stain.
I don't care.
But the inner one is not possible.
There is a lot of important information about the lathe.
It comes with each set of collage.
Okay?
We will continue now.
When we rest the lathe, we will continue with the 90.
God bless you.
Of course, now, after we have rested the lathe for 10 minutes,
But there is an important point that I forgot to mention in the comments.
A guy asked me, when the car was still upstairs,
He asked me, why is it 90 in 90?
Okay, brother, look.
When you tighten here, it is 30 Nm.
You are reaching the end of the lathe.
You have something called, the first 90 that we tightened a while ago, it is called the shag.
That is, we tightened the lathe now.
The second 90, why did they put it there?
It is called the pressure.
Okay?
As it is written here.
Okay?
Now, this shag is the pressure shag in the center of the lathe.
The first 90 shag was 90 degrees.
This 90 was the shag.
The second 90, the last 90, is the pressure.
Now, we will tighten the last lathe.
So that it presses correctly in the center of the lathe.
Okay?
From the 90 shag, we will continue.
We will start with the first bolt.
As we have tightened from here.
From the shag.
Okay?
This is the first bolt.
The second.
It comes here.
This 90 is called the pressure.
Okay?
We did not tighten one or two.
The third.
This is the fourth.
So that we do not forget.
You have tightened correctly.
Okay?
The fourth.
What comes next?
Okay?
The fifth.
The sixth.
Okay?
The seventh.
Here.
Okay?
The seventh.
The last bolt.
Okay?
Now, as I explained to you a while ago.
This is the shag.
The first one is called the shag.
The second one is called the pressure.
This is the 90 pressure.
We should have finished and tightened.
As required by the agency.
Nothing is different from the agency's work.
Okay, guys?
Of course, this is the second part.
I will upload the video.
I made the first part.
This is the second part.
And the guys who are asking me.
Why don't you upload the whole video?
Because this is the basis of the educational page.
Okay, guys?
And during this period, I am focusing on mechanics.
God willing, in the next period, I will return to electricity.
Okay, guys?
If there are any problems, I will publish them again.
The guys who are asking me.
Why don't you upload the video?
I will upload one video.
On the assembly of the engine from A to Z.
In the detailed explanation that I am explaining there.
The video will be more than 20 minutes.
And it will be boring.
So I make short videos.
And each part is separate.
This is the second part.
The third part.
I am putting 100 centric and zinc.
So that the page is clear.
And for those who are following.
For those who are following.
You will understand how the engine works.
I don't make a long video.
Why?
Because my idea in this page is based on education.
And each engine that I have in the pages.
Of course, all the videos are available.
I publish them from A to Z.
Whether I ride a car and work.
But we have finished this second part.
Thank you.
