10 Video Views·Oct 5, 2025
Gtech Leaf Blower LB01 Repair (and strip down) in yet another of our Gtech strip downs.
A leaf blower is expensive, and it is disappointing when it goes wrong. But, there is very little to go wrong, so maybe it can be repaired.
See other Gtech repair films in the Gtech playlist
https://www.youtube.com/playlist?list=PL7-hz4M-3Ec1eCEGSDtxTMQvRrT8OnKnH
▬ Contents of this video ▬▬▬▬▬▬▬▬▬▬
0:00 - Meet SSP
0:10 - Leaf blower
0:20 - Test the battery
0:50 - Clean Terminal
1:10 - Take back off
1:50 - remove inner skirt
2:10 - Remove motor
2:22 - Fault discovered
2:45 - Solder contact back on
3:38 - Tape cables strong
3:50 - 1st test
4:13 - rebuild
4:20 - back in use
4:35 - the crime
This channel comes from Jean and Stuart, and it is mainly on cruising with ship tours and port guides. We hope these films form useful research and help you remember ports you have been to and show friends.
Not everyone gets cruising, they like paying winter fuel bills at home (LOL - not), so if you know someone who is not a cruiser - and we were not, didn't think we would like it, and almost never went even though it was at no cost to us - then look at a few films. We went on that first cruise (sent by ITV to talk about Emmerdale). We loved it, we got addicted, and after a few cruises, we started Doris Visits. I would suggest that if someone says they didn't like cruising, it is like saying they don't like hotels. That is all a ship is, a floating hotel. I would suggest that their negative experience is because they chose the wrong ship, and we list over 450 ships on Doris Visits. www.DorisVisits.com
See our dead Gtech battery quick fix = the solution applies to many batteries.
https://youtu.be/MHPk0tdFsh4
so okay this is a g tech leaf blinds the
original very first one
i think they call it lb01 but there's
only three things involved a battery
a switch
and a motor one of them will need
replacing
the part with limited life is the
battery a battery is about half the cost
of the leaf blower
four quadrants light up it shows the
battery is fully charged and when i
tested
between terminal 1
the plus sign and the other side minus
i had 41.4 volts
there's nothing wrong with the battery
and the terminals i push together
slightly here with a small screwdriver
to ensure they make good contact but
they're clean there's nothing wrong with
them pull the trigger it fires the
battery but no leaf blower the switch is
working so we're going to take this
little baby apart
essentially the back needs to come off
and then the handle assembly so the
battery is disconnected we'll need to
attack the screws with this it's a hex
screw or an allen key a long allen key
will be needed for the back
because the holes are recessed
on top you could use the allen key or
you could use um
a weak electric screwdriver beware
electric screwdrivers have so much
torque
or power they could break the plastic
so we lift the back away
careful not to break the lugs because
there are four lugs that stick out
these do break with vibration in fact
i've only got three out of the four
still intact
next remove this inner skirt which comes
out very easily
and we hope the motor
hasn't actually gone wrong
ease the handle assembly away with a
little nudge but be careful there are
wires to the motor
now we remove the motor which is four
screws one in each corner
and then just pull it free
now we discover what's
broken
a cables come off the motor probably
with the vibration or the torque as the
motor starts to twist and stops
there you go
i could say that's not rocket science
but there are people
who put wings on these leaf blowers
and make them into aeroplanes and
rockets i just do not look on youtube
anyway we now have to solder this cable
back onto the motor
and i'm sure it's going to work
unlike their other appliances gtech
actually only list on their spares a
battery a charger or buying the complete
whole unit once again as a body remove
the battery before soldering any
electronics make sure any of the brittle
copper is broken away so you get really
down to something quite tough
and then with a blunt blade and only
working away from you and being very
careful
just scrape it so the copper shiny
copper comes clean
if you're not familiar with soul ring
it's probably best to leave it to
somebody else but the idea is that
everything has to be clean
and both joints need to be hot the
solder needs to run freely and you hold
it still while it cools down
it was insulated and it's good practice
so i have actually taped it but i'm also
going to put a piece of tape to hold the
two cables together two together twice
as strong
so it's time to test
and
it
works it works without spinning off the
table
and it's time to put it together again
note there is a slit in the side of this
plastic that's for the cables to go down
put it all back together and it fits a
treat
if you love a great thriller
with some pumping action
and twists and turns that keep you
wanting to go on to the next page then
cruise ship heist is probably the book
for you and it happens on a cruise ship
my name's stewartson paul i've been a
director i've written lots of
screenplays but this is my first novel
and it all takes place on a cruise ship
this is the kind of view that every
cruiser is used to leaving a port well
in this book they leave a port but with
millions of pounds on board that isn't
theirs
and that's where it all starts to go
wrong
cruise ship heist
you