4 Video Views·Oct 6, 2025
In this Gtech K9 - Handheld - Complete strip down and clean the Gtech handheld K9, is stripped down, cleaned, and fixed. Gtech K9 revealed inside. It gets quite filthy inside, so the K9 Gtech is broken down and cleaned. Switch repaired.
See other Gtech repair films in the Gtech playlist
https://www.youtube.com/playlist?list=PL7-hz4M-3Ec1eCEGSDtxTMQvRrT8OnKnH
▬ Contents of this video ▬▬▬▬▬▬▬▬▬▬
0:00 - Multi K9
0:10 - Won't switch
0:20 - The fix
0:40 - Test
0:50 - strip down and clean
1:28 - Remove bottom
4:50 - Re-assemble
This channel comes from Jean and Stuart, and it is mainly on cruising with ship tours and port guides. We hope these films form useful research and help you remember ports you have been to and show friends.
Not everyone gets cruising, they like paying winter fuel bills at home (LOL - not), so if you know someone who is not a cruiser - and we were not, didn't think we would like it, and almost never went even though it was at no cost to us - then look at a few films. We went on that first cruise (sent by ITV to talk about Emmerdale). We loved it, we got addicted, and after a few cruises, we started Doris Visits. I would suggest that if someone says they didn't like cruising, it is like saying they don't like hotels. That is all a ship is, a floating hotel. I would suggest that their negative experience is because they chose the wrong ship, and we list over 450 ships on Doris Visits. www.DorisVisits.com
See our dead Gtech battery quick fix = the solution applies to many batteries.
https://youtu.be/MHPk0tdFsh4
Please subscribe to this channel and share with friends.
if you've got one of these little babies
uh it's expensive and it can go wrong
it's a gtech multi
k9 and the most annoying thing with it
is it just won't
switch on and off but if that's the case
i can probably cure that within two
minutes there's a little hole here a
little ledge for it
and the screwdriver goes in there and
wedges
the switch out and
very simple to fit you literally take it
out of the box there's your new switch
there's the uh what do you call that a
lug
that goes in at the bottom and then
you push it in firmly this machine is
now mended
so start to take this apart first thing
let's get the battery off the battery
comes off by pressing these lugs in hard
really hard in fact i've got to use my
right hand
getting to the age where i'm not as
strong as i used to be pressing in the
lugs
it comes off dust coming off them
mask you might need a mask um
i neglect to wear one too many times so
the screws that we need to remove are
going to be here
these are the easy ones and then we're
also going to do these
uh screws and take those off as well
you'll find they're a little hex shape
so this is the correct hex i'm going to
start with the bottom
four screws
so four screws and i said the first ones
out i'm going to lay them on
our sticky paper there so i don't lose
them
now to lift this off you can see we're
going to have to go further because this
is attached to that
so we're going to undo these ones now
these screws you can see when you
actually get them out are
smaller
so we're going to put the two of them
next and the reason i'm putting those
there is there from the bottom
they're the next up i don't want to
start trying to screw those into
the place that's meant to have short
screws
remember these come out at an angle
they're not they're not straight
so at an angle
these are short screws as well i wonder
if they're the same size
so again at an angle
that's why we've got our extender there
and a nice brown cloth so we can see if
we drop anything
there's the last one four
four screws and i'm going to lay these
on the paper separate to those two
just in case they're a slightly
different length i'll check those in a
minute
because we'll be able to see if they are
a different length now we can actually
see this is not uh
part of the bit the middle piece just
lifts out
and i'm going to put it next to its two
screws
so oh look that's pulled out as well now
easily
so let's put that next to its four
screws
so we're gonna dust all this out with
the paint brush
there we go sorry it was a bit of a
stretch look
get it gently paint brush is nice and
gentle
i'm going to get it all clean all the
electrics all of this which is
everything clean this last bit is um
it's a bit trickier to get out so you
might want to avoid this
uh but it's got six screws
so when you do get it out as well it's
actually attached by a cable so you
can't just pull it off regardless you've
got to pull it off
easily and just leave it sitting there
wires attached here so
literally just take it off very gently
it's got a slide when it comes back it's
got to slide into here
but it's worth doing because just again
now remember i've done this very
recently
i took it apart so that i could figure
out how it works
before i made this film and if you're
worried don't do this last stage don't
take this bit out because this
is slightly more difficult so here we go
we're going to clean
this and we're going to do the other
side
just take this out now this has got to
slide back in there
there you go sliding the bits back in
there
one two three four five six screws got
to go back here
they're all the same length they're all
the same length so and i left them till
last now
here's here's another thing if you drop
them they'll get stuck to this magnet
if they're not stuck to the magnet
you'll need to um
to shake them out so we're going to
tighten these up now
and then this part is back together
don't over tighten them you don't need
to they're only going into plastic
um you can actually do them by hand
rather than the machine
machine might be a little bit harsh the
machine saves time undoing it
it's got a nice torque to it to undo
them if they're a little bit tight but
literally these can be finger tight now
there's only six it won't take long so
that's the base back on
as i say this machine was you can't
believe how filthy it was inside
when you take yours apart you'll see so
next we're going to start putting her
back together
this part was next i've brushed it
already but
the just making sure there's
nothing on it that
needs breaking up no hard lumps that's
been they've been there ages let me just
[Music]
get the brush again and brush it out see
the
little dig with the screwdriver we have
um two little pieces left
and this piece is going in first
in there so this is this is where you're
going to go oh no i wish i'd never taken
it apart
um because you're going to try and get
this on a million different ways
and you'll go i can't line it up it
won't go in doesn't matter how much
and you're going to try and you're going
to want to
try and line these edges up
with these edges well fair enough they
do but that's not important there's no
real slide to it what we're looking for
is these devils
with the big holes i'm gonna slip over
these small ones
so that's what we're looking for is to
line these two up
see if you can see inside there we go
look we're looking to line those up
and once they do it just pops on
and then we look to put in the long
screws
and they go in at a slight angle
and again we can use the uh this in the
hand
they're literally going at an angle and
if you force them
you'll ruin the thread and
finger tight on all of them is quite
enough
yeah i love taking things apart
and um so for me it's a bit of a
it's a bit of a game but if you're
worried if you think you'll end up
breaking it
then don't do it don't do it
and i'm not saying this is the correct
way to take it apart
it's just the way i've done it so the
next and the last part is this
again it's all about lining up the the
screw holes which fit into each other
and when they're lined up it literally
will just pop
in last two screws
it's all back together
and it's this piece here uh that lets
the machine know it's all connected up
then you'll be able to switch it on
but here's the trick if you take out the
foam filter there is nothing in here
that really
can't go in the dishwasher and this has
been in a few times and comes out
sparkling clean
now they do say don't put foam in a
dishwasher
i've taken out the scented candle if you
don't have one of those
you should put a little plug in there
i've actually put this in the dishwasher
too
well the dishwasher's finished
and i just want to show you how clean
this
is now there we go
pretty clean spotless in fact
and this is one we cleaned ages ago
and don't forget to put the plunger in
or a cap this actually smells alright
still so we're going to use
but the serial number at the bottom as
you can see is the battery
serial number all the appliances all the
accessories have serial numbers
here's the serial number of the hoover
which is uh is at the top
so where do you find the model well
the model number is actually hidden
behind
the uh the waste bag bucket
easy canine pulled apart and
put together again after it's cleaned
works fine
thanks for dropping by and i hope the
film
helped you uh if it did please help me
by dropping by and having a look at my
books i'm a novelist and i write crime
fiction
crime that happens on cruise ships so
cruise ship heist
cruise ship serial killer cruise ship
laundry wars
uh which is about human trafficking and
uh cruise ship art theft
four great books start with any of them
but cruise ship heist is the first one
thanks very much see you again soon