0:00 Intro 0:21 Why do we want to plane thin stock? 1:23 The Jig and how it Works 3:45 Building the Sled 4:10 Example 5mm Thin Work Piece 5:25 Conclusion
good morning fellow woodworkers welcome
back to another video so recently i
received my metabo d830 thickness
planner and i was using it extensively
up until this point because it's so much
fun and i ran into a tiny little bit of
trouble while dealing with the planner
namely you shouldn't plan anything that
is less than one centimeter in thickness
using this planner now
usually for my premium 10 seconds over
on stemmage.eu i receive planks like
these okay with a thickness of about
five to ten millimeters and most of the
time they come with a very very rough
surface and in normal case i need to
send the surface down in some way but it
takes ages and i want to use my planner
to get rid of this rough surface and i
actually figured out a way to plant thin
pieces of wood this also applies if you
want to take a thicker piece of wood
okay like two centimeters and you want
to plant it down to let's say eight
centimeters instead of re-sawing if for
example if you're not familiar what
resawing is you're going to basically um
restore the thickness of a board and
many people don't want to do this on the
table saw because it's it's pretty um
experimental
and dangerous to do so and they would
like to use a thickness planner for that
i'm going to show you how you can plan
figure boards to a tiny thickness or
just
very thin boards to an even thinner
thickness using the blender today
now this right here is my metabo da330
thickness planner and it's a wonderful
tool it works wonderfully you can find a
review video down there in the
description check it out if you're
interested in this tool you should get
yourself one of these very stable very
good work tool um by the way if you
enjoy these kinds of videos why not
subscribe to tenner would support the
channel a lot now all you really need
for planning thin pieces of wood is well
just a scrap piece of wood you have
lying around we are going to turn it
into
nice and easy to build chick now you see
here i still have a piece of mdf lying
around which i use most of the time as a
fence because
for my jigsaw i need a fence to get
perfectly straight cuts you can also
find a link to the video than the
description how to do that now
there are only two conditions for this
jig to work out now the first one is
that it actually fits into your planner
i mean we don't want it to be too wide
okay otherwise it wouldn't fit in into
the planner mine takes a width of like
30 centimeters okay in into account as
the maximum so yeah this right here is
definitely going to fit into here and
the other condition which is the most
important one is
that your piece of stock
actually lies completely flat on your
jig
it's not supposed
to hang over your jig for example this
could be dangerous this could break your
work piece so make sure that the length
of your jig is actually the same length
as your work piece or even longer that's
even better and for extra security what
we are going to do with this chick is we
are on the one hand going to use double
sided tape to basically tape our
work
to our jig and the other thing is we are
going to place a tiny little fence on
the front line here there is a reason
for that because your planner in a
normal case is going to push your work
piece in this direction through okay now
just imagine that your double-sided
tape isn't working as intended and now
you're going to have the situation that
your workpiece is going to slide
off your table in some way or
since the direction of the planner is
going to go in this direction is that
it's going to shoot out to the front to
counteract that we are just going to
place a tiny little fence right right
here using nails or something inside of
the jig and then nothing bad can can
really happen it gets pushed against
this chick against this fence and then
everything should work out normal case
even without double-sided tape this is
just a double check
[Music]
and this is literally it all you have to
do now is tape down your stalk using
double sided tape and then we can let it
run for the planner safely that is good
safety always first kids
really doesn't matter which side both
sides are pretty much ruined with those
marks so yeah let us go with this one
and let's start with taking off one
millimeter
just look at that
wonderful
absolutely wonderful there's still a few
marks but we got it through safely and
now the other side let's try it too
[Music]
and do you know what the best thing
about this method is it just works
nicely and it's very safe and your
workpiece won't break or anything it's
just it's just absolutely wonderful and
so easy to do with a bit of scrap wood
honestly the hardest part about it is
getting it off your double-sided tape
without hurting your wood gut wonderful
looks absolutely perfect
nice and thin piece and this method is
so safe and it works out just crazy good
and you should try it too
always make sure to have a safe
workspace okay never try to do weird
like putting two thin stock into a
planner always make sure to use a jig
especially if you're new to the
woodworking business like i am
and if you do enjoy these videos and
definitely make sure to subscribe to the
channel for more working and diy content
and up until the next video i wish you
guys a flammable day ciao
[Music]
you