Today we take a huge slab of olive ash and turn it into a fine dining table with embedded c-channels and a steel cross base :) We flatten the slab manually, power carve to preserve its live edge as best as possible and finish it with rubio monocoat for an AMAZING grain pop! Enjoy! =D
Today I show you how I created my first single slab table which was also my biggest client order yet.
What I learned along the way and also I do some freestyle power carving. Enjoy!
This is gonna be so much fun! Yay!
Today's a special day, you know? I finally got a huge order for a dining table and couldn't
wait to get started. If you've watched my workshop vlogs you might be familiar with those two huge
ash slabs.
This is why I study physics! It works out so nicely!
Yes! Okay, I think it would be harder to lift it up here and yeah.
Which side is better? I think that's the wrong side. I shouldn't use this one.
Yeah, it's time to put it down again I suppose. I think you can see why this side isn't the best
one to use. I mean it's a huge slab, it won't tip when I use the router on it but just to make sure
I'm going to put it with the concave side downwards just because it's going to give me a
more stable setup in the process. My client decided to choose the one which was less rectangular
and asked me to keep it as natural as possible, meaning I had to preserve the live edge.
First thing on my agenda was to simply flatten both sides using my huge flattening jig that
I've built a few videos ago. All relevant links can be found on there in the description by the
way. This right here ladies and gentlemen is the true big chungus. I think you need a license to
use this weapon. It has half an inch of diameter just for the shaft. It's ridiculous. I had to buy
myself this half inch diameter shaft for my Festool router. I'm seriously afraid to use that
thing. There's a lot of power behind bits of this diameter. That's outright ridiculous.
Yeah it's freaking crazy. I also have a smaller one but for this big of a slab I think the bigger
one would be more suitable. I'm not certain. Just imagine I miss the direction of the router up
if I do an accidental line cut with this thing. It's gonna be fatal but I think I know the
direction. I do hope so. Yeah let's use the big one. Let's go in completely. I'm so afraid. I'm
so terribly afraid of this thing. No need to be afraid. That thing works so smooth. It's ridiculous.
You nearly hear no voice. It's so quiet. I could even go deeper. This is crazy. Great performance.
I love it. Let's continue. Nearly no heat. This thing was worth its $150 I think. That's a great
bit. That's a seriously great bit. And it's not even carbide. It's amazing. Greatest thing about
that is always the mess that it produces and I can see clearly in here. It's dusty everywhere.
I need to put on my mask once again. My respirator. But yeah such a lot of fun. I can still sell those
believe it or not. And we are almost done flattening that one. It already looks ridiculously
good. Yeah awesome. Awesome results. And it didn't even take that long. I think for one phase it takes
me like 10 minutes. That is ridiculously fast with this router bit. I'm so pleased. So pleased.
Just look at the grain. It gets better and better the deeper we get. Oh such a beautiful one.
That's going to be a great tabletop once finished.
There's dust everywhere. Yes. Dust seriously everywhere. It's so dusty in here. But I got
the first side flat. Do not wonder I forgot my camera at home today. So I'm using my MacBook
at the moment. Now I'm looking for my room and then we can see what the slab looks like.
Looks pretty fantastic in my opinion. Is it just me or is that slab looking kind of
thick. That is. Look at the grain. This is outright ridiculous. It nearly looks like olive.
Okay let us now check if the whole thing is actually square because I'm wondering if the
suit jig is actually working the way it's supposed to. But from here it looks terribly square. Let's
see. Whoa. Looking square to me. There is no light shining through. That's an amazing result.
Now I can just hope that it won't bow too much in the next few days before putting in the seat
channels. I'm a little bit afraid. Now we are going to turn the whole thing around and then
we are going to flatten the other side. With one reference face already flat I can just put it on
the other side and then start milling again. Yeah looking fine. So satisfied with the result. Let's go.
I think we can all agree that the performance of this cutter is outright ridiculous.
Link down in the description. It's seriously worth it's 150 bucks approximately. Okay now I'm going
to rough sand this whole thing such that I get rid of these marks. You can't really do anything
about those marks that you get after routing. And yeah then we already did a great job I suppose.
I'm still waiting for my Arbotech mini carver which I'm going to use to basically... Here we
had to take something off with the chainsaw such that I can fit it in my car. Maybe you can see
it here a tiny little bit. So I need to basically imitate the live edge of the slab with a carving
device. Never did that before but it's certainly going to be a lot of fun. And also I need to get
rid of all the bark right here. We don't want the bark. By the way this right here is the downside.
The live edge is going to point downwards as a natural chamfer you can say. There's still a bit
of stuff to do but not too much. So let's get to work. Sanding took a while but I got both faces
done in about 30 minutes with an 80 grit. That took a while but it was still totally fine. Now
I'm sitting on my shop vac. As always I'm extremely curious as to how the grain is going
to look once finished. So I'm going to water pop this one and it's also something for you to really
enjoy. So yeah let's go ahead and get started. This is only the downside. The back side. On the other
side we have way more hardwood which is going to look even better. Yeah let us pop that bitch
and then we are going no let us pop that wood cherry and then we are going to continue our work
with removing the bark from the live edge. I think this is going to be a bit of a harder task. We'll
see. This is obviously only going to give you a rough estimate for how it's going to look at the
very end but I think we can all agree that it already looks rather fantastic and once finished
with ruby or monocoat it's going to look even more fantastic. It's going to really pop and cool
thing about the slab is that we have a lot of curl here. So we got curl at the parts on the live edge
also on the other side and we also got a curious kind of curl here which is rather interesting.
Next came a few cosmetic procedures such as cutting parallel ends with my track saw and
both ends with my router for these spicy looks. The slab had just a few minor cracks at its ends.
The client wasn't very fond of me using bow ties so we decided to go with a different route
namely pale white epoxy. The resin is really only there to stabilize the cracks and to keep them
from further opening up due to moisture differences in my client's home. I also sealed off the end
crane with resin too to keep the slab from drying out or absorbing moisture too quickly later on.
Next we will try to keep the slab from naturally straightening out along the crane
or in other words we will embed c-channels at the bottom to prevent the piece of wood from
bowing or carping. The c-channels are made out of steel and after cutting them to size I started
to mark out their positions on the slab. Once that was done I route out the shaft where they will slide
look at. I fasten the c-channels rather loosely later using threaded inserts and bolts. This is
always by far the most annoying part about table builds in my opinion and no fun at all. But what
needs to be done has to be done. So let's quickly get this over with, shall we? Never, and I say
never, fasten those too tightly. We want to allow the wood to move. Screw them in too hard and your
wood will crack instead. That would suck, right? Done, nice. Now let's rinse and repeat on the other
side and then we get to installing the base. The steel base has been provided to me by my client
so I had to deal with whatever he's gotten for me. At first I centered the base and marked the
positions of the plates. Then I used my trusty CNC to create some templates such that I could
easily route those marked sections out, inserting the base flush into the slab in the process.
Fitting perfectly, nice. Next came the fun part. Again, 60 times, yay!
So most things turn out very nicely up until now when it comes to inserting the seat channels and
the line, but I've got a huge problem with the space. I left a bit of clearance for all of the
parts which would go into the wood, where the wood lies on. But the thing is, all of those
platforms that you got here, those four touching the wood are not co-planar. I loosened those
screws when my client got the base here, they already weren't co-planar. I loosened those
screws, they are not tightly screwed up until now, tightly fastened, but they are not co-planar,
meaning they are always at some kind of angle touching the wood and this makes it really hard
to assemble and this also makes the clearance look rather weird, a bit uneven. That's how I
predicted it would be. Yeah, these are the problems you deal with when you don't manufacture stuff on
your own and have to deal with hardware that someone gives to you. But it's the downside of
the table, so no one's going to see it. My client knows it, we talked about it and all is good,
but it still poses a tiny little problem when fastening all of the screws. But lately we are
using threaded inserts, meaning we always have a little bit of wiggle room and we can fasten it
very tightly, even though they are not co-planar at all. Let's continue. There was a bit of work,
but I got it done. Yeah, we are almost done. Now I'm simply waiting for my mini-carver by Arbotech.
It should have arrived by now in my home, so I can start carving tomorrow and then it's only
sanding and some fine-tuning, like a bit more chamfering on the live edge. Yeah, I'm pretty
satisfied with how everything turned out up until now. Is that a certified bourbon moth's woodworking
moment? He does ---- like that, right? I should also eat some glue, I suppose. Let's go. I didn't
want to sit around and do nothing until my carver arrived, so I already went ahead and prepared my
underside for finishing. First sanding all the way up from an 80 to a 320 grit.
Cleaning the surface and ridding it of all the dust using Rubio cleaner.
And then applying the natural Rubio monocoat finish as well as
chiseling my pants upon witnessing the immensely sexy crane unfolding upon my very eyes.
Next day rolled around and I finally got my mini-carver, which I'll review soon here on
this channel. Up until then though, you can now watch me do my first ever power carving on a single
it's extremely exhausting. I notice it here. It's such a weird motion. It's seriously exhausting.
The other thing is that it works out like a charm and I'm really satisfied with how it worked out.
Brush shaping is done and now all that's really left to do is to sand. Yeah, this is seriously
cool. I like this thing. That is amazing. And the Rubio monocoat is already pretty dusty,
but that doesn't matter. I can clean it up. Most of the time I'm rather critical with myself,
but this turned out nice. I seriously can't complain. If you wouldn't know better,
you would think it's a live edge. Sure, nature is the best former of live edge there is, obviously,
but this is pretty damn nice. If I would just feel under the table and wouldn't know it has
been carved, I wouldn't know. I would feel, yeah, this is good. That's a nice live edge.
Pretty satisfied. Gotta send this up to a higher grid next and then we're already done with one
I think that it looks pretty cool and adds a lot of character to the piece. Yeah, now I'm going to
power carve sand it up to 320 grit. I got a bunch of sanding discs here and then we are basically
on the finish line. What I noticed over the weekend when I left it here, it developed a
tiny little bow. This whole table top. I asked my client and he said that it's fine. It's natural
wood. We will never get it to be perfectly flat at all times because through the seasons it's
going to bow and then it's going to unbow, etc. So I'm just going to leave it how it is. The
difference on both sides in comparison to the basically to the top of the curvature is about
two to three millimeters. So it's noticeable if you use a level, but other than that it's not
too much noticeable. My client is good with it, so I'm also good with it. I informed him about it
and we are both on the same page. Let's get to power sanding and then we are basically done.
Then we are going to sand all of the rest and then we are going to coat it and that's about it.
And that's basically about it. There's not much more to it. Now we enter the finish line.
At first came a horrendous amount of sanding which took me about two hours.
Again I took all steps up to 320 grit and also water popped the surface and sanded again from
it was time to add the finish to the top. The result really speaks for itself. Enjoy!
Now that turned out gorgeously, won't you agree? My clients were highly satisfied and the slab
stayed completely flat and uncapped even after adjusting to its new home. I hope you learned
something new today just like me and if you did why not make sure to subscribe to the channel for
more tweaking content. I post regular over here so definitely make sure to subscribe and support
the channel this way. Also I create handcrafted products over on my shop stemmer.gu so also check
out my website. Until then I wish you guys a flammable day and please stay safe. Ciao!