Today we will build a crosscut sled from a MDF board which will be an essential tool for your workshop! It only takes an afternoon to build and does a really good job at making square cuts. Enjoy! =D
today we are going to construct an
inexpensive and quick to build crosscut
sled from an mdf board stay tuned
good morning fellow woodworkers welcome
back to another video so let's get
straight to the point of the video i
hate this table saw right here
this has been my first one it was like
80 bucks and you can just see what
terrible quality it has the defense was
made out of aluminum every time i apply
pressure to it it tends to bend and this
is not good you can't get any kind of
square cut with it also due to the
vibrations of the table saw which it
does all the time it's losing its screws
and it's just not stable overall and the
most terrible thing is the tracks that
you get right here are so tiny you can't
recreate any kind of good sled for it
this is why i decided to buy myself a
new table saw one from einhell and this
table saw right here has everything that
i want it has a nice table okay it's
made out of very durable aluminum but
thick one also you can get cuts which
are really square to the table okay 90
degree angle also it got nice tracks
such that i can create fences and one of
the most important things out of all of
this i got a nice measurement here where
i can measure and
put this nice and stable fence to it
this is good because this way i can get
nice cuts and what i want to do is i
want to create a simple crosscut sled
today i think it's called a crosscut
sled in english and is what we are going
to do today and you can follow along and
build along and build one for yourself
first i took two scrap pieces of spruce
which by coincidence fit perfectly into
the tracks of my table saw and plant
them down with my japanese scanner till
they were flat with my table saw surface
next i shorten them to the length of my
tracks with my handsaw
and once that was done i took a 1.6
centimeter thick mdf board and marked my
cut
i wanted the sled to be as wide as the
tracks were long and all of this
happened when my dogs were going nuts in
the background by the way what the hell
are they doing
[Music]
after securing the board i attached a
quick jigsaw fence to get a square card
want to know how that works it's
actually pretty easy link to my video on
the topic can be found on there in the
description
[Music]
once the car was done i chamfered the
edges of the board a bit and then
removed the divider from my table saw
we need to raise the blade into the sled
later so the divider would get into our
way in some point so definitely make
sure to remove it at first
after it came off i installed the plate
again for my own safety and proceeded
with the building procedure
next placing the sliders into the tracks
and then laying the mdf board on top of
it i made it really sure that everything
was square before screwing everything in
place
then i marked the middle of the sliders
on each end and connected the dots the
guiding lines are where my screws will
go in by the way
and then i really screwed it up when
fastening the board like
literally screwing
there was nothing else to it
[Music]
last but not least our sled needs to
keep its together after being cut
in half for that reason we place the
connecting fence on top of it which will
also serve as our 90 degree cross cut
attachment
making that boiler wreath smooth using
my planner and chamfering its edges a
bit for the memes i then attached it to
the front of the mdf board once again
making sure that everything is highly
square with the mdf factory edge
just for your information a tiny arrow
in placement will mess up your whole
sled
your cut just won't be square to the
plate anymore so really make sure to go
at it slow and carefully here that's a
very important step
on the opposite side of our fans i also
secured another connecting block
and last but not least i raised the
blade of my saw carefully into the sled
and made my first cut through the whole
jig
and now we are going to answer the most
important question
will the piece that i'm going to cut
with the slappy square let's find out
[Music]
now let's find out this right here is
the part where i cut through and now
let's use the square right here okay
it's an old one and
oh
this is really surprising i can't even
see
light shine through this is actually
really surprising i thought that it
would be not as accurate as i intended
it to be but it's even more
accurate than i thought so really
surprised about it actually
and that's about it if you want to see
more diy projects and woodworking then
please make sure to subscribe to the
channel and to share the videos around
for more exposure here on youtube you
know youtube algorithm only supports
channels which get a lot of views et
cetera subscribers so definitely make
sure to support the channel that way
also don't forget to check out stamet.u
for more handcrafted products thank you
very much please stay safe and don't
forget to tune in for the next video see
ya have lumber day
[Music]
[Music]
you