Starting Insulation and Interior Siding - DIY Off Grid Cabin Build Episode 45

The Woodhaven
54 followers
66 Video Views·Sep 14, 2025
In this video, I start on the insulation and interior DIY siding that I made from 3/8" CDC plywood. I'm prepping this side of the cabin for a small storage loft.
If you are planning to shop on Amazon, consider my Storefront:
https://www.amazon.com/shop/thewoodhaven
Check out Amazon's Hottest Deals (updated hourly):
https://amzn.to/3K5ybkn
Check out Deep Discounts on Open Box Tools:
https://amzn.to/3MeYZ3h
Music Links: https://artlist.io/Daryl-3392866
DISCLAIMER*
This video and/or description contains affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
all right
back at the cabin and I'm working on
this side of the cabin I want to get
this all prepped and ready for me to
build a loft on this side as well
and um before I can do that I need to
insulate this wall and uh
maybe these uh two sidewalls and I want
to get
the roof insulated at least up there
so that's what I'm going to work on
today so let's get to it
[Music]
thank you
[Music]
[Music]
foreign
[Music]
foreign
stuff
so now I've got to cut some
skinnier strips of insulation for those
two corners
cut off some smaller pieces for the top
there and then one over there
I don't know how that one got a little
bit short but uh
anyway gotta fix that so
let me throw these on the floor get on
my hands and knees and start cutting
thank you
[Music]
[Music]
foreign
[Music]
[Music]
[Music]
thank you
[Music]
[Music]
[Music]
thank you
[Music]
[Music]
[Music]
thank you
[Music]
foreign
it's not pretty but
it'll do
let me get this other few pieces done
and we'll bring you back
all right I've got my Corners installed
got that strip up there
those two strips up there installed
so now what I need to do is get started
on
the roof insulation
but before I do that
in this Edge I don't have
a staple strip
there's no uh rafter exposed there for
me to attach the insulation to
so what I'm gonna do
so I've got a two by two that I'm gonna
tack up there and let it simulate the
rafter but I have to cut it to length
got it marked
so let me go make that cut get that
installed and then I can get started on
the roof installation
foreign
[Music]
okay now I've got a simulated rafter up
there that I can attach my
roof
insulation too
but before I do that I'm actually going
to start on my siding I want to come
below
the mark where my uh
my loft is going to be I've got that
marked on the wall
so I'm going to go ahead and start
installing
this and I'm going to come down four
rows and that'll get me past where my
loft is going to be
[Music]
foreign
[Music]
foreign
[Music]
all right I've got all the rows that I
need installed that'll give you a little
bit of an idea of what the interior
siding is going to look like
but now
I really should do the the sides too but
I think I'll be okay there it's not that
far to reach over
this loft is only going to be 32 inches
deep
so it shouldn't be too difficult
so now I need to start on
my roof insulation
been looking forward to that all day
all right this first one's not going to
be fun because this will be the one
where I figure out how to do it
[Music]
good
[Music]
thank you
foreign
[Music]
[Music]
[Music]
[Music]
thank you
[Music]
foreign
[Music]
foreign
it's why I've been looking forward to
that all day
can't wait to do the next one
all right I've got an idea
this second one was just as hard as the
first one that it's too much but I've
got an idea that I think is going to
make it a lot easier but it's going to
require me to attach a few of the uh
ceiling slats
the issue that I'm running into right
now is you can see here that I run out
for three inches and then
I have a Bend
and this plywood I don't think I can
bend it without
scoring it on the underside so I need to
go over three inches
make a cut that's only as deep as one
layer of the plywood
and then I think it'll be able to bend
around that corner but
I need to go get a couple of those I
need a short piece there that's 22
inches and then I need a full one here
and both of them
scored lengthwise
on the three inch Mark so let's go take
care of that
[Music]
thank you
because
all right believe it or not that
actually worked
so I've got my depth set I'm going to go
ahead and cut
uh
at least one more right now and then
I'll show you my idea for making
installing this insulation a lot easier
all right you probably figured out my
trick by now but uh that's what I'm
gonna do every now and then I'm going to
have one of the boards go all the way
across
and that will help hold up one of the
ends
of the insulation and that should make
this a lot easier
so that uh
scoring the the board actually
worked out pretty nice
I'll get a closer look here
see right there
where it's scored it's not much of a
Bend but it's enough
and the board looks all right
I think that's gonna work
all right I think
I think that's going to work to help
hold up the insulation
[Music]
[Music]
foreign
[Music]
[Music]
[Music]
let's see if this
makes installing this insulation easier
foreign
was it easy no
was it easier yes
so I'm going to call that a success
all right I got enough done so that I
can start on the Loft on that side of
the cabin
but this is going to do it for this
video uh we'll get on to The Loft in the
next video so uh
thanks for watching and talk to you guys
later
