I TURNED A FAMILY HEIRLOOM INTO AN ENGAGEMENT RING

Handmade Jewelry
2 followers
Sep 16, 2025
One grandson wanted to use the ORIGINAL GOLD from his grandmas cross for an engagement ring. Two diamonds from the cross were used as accent stones, and I supplied the one carat LAB-GROWN DIAMOND for the center.
Have you ever wondered if you can re-purpose your old jewelry? This video shows a step by step example.
YouTube— SUBSCRIBE to Modern Goldsmith: http://bit.ly/34wTGGw
Instagram— Follow me on social: http://bit.ly/2OtLWiV
Business Website— Portfolio and Contact info: http://moderngoldsmith.com
This gold cross is an heirloom,
lovingly passed down from a grandma to her grandson.
He now wants to take it and turn it into an engagement ring.
That's where I come in.
It starts with the design,
which is then 3D printed into a wax model.
In order to cast this wax model in gold,
it first needs to be sprued up.
I'll be using my trusty wax pen to do that.
I heat up the wax base so the wax starts to melt.
After the wax base has been heated up,
it's time to attach the ring model.
The ring model and the wax base are both fused together
using that same hot wax pen.
After it cools, they're joined together.
At this point, a three-inch flask is added to the wax base.
Now it's time for investing.
First, water is added into a mixing bowl,
followed by the investment powder itself.
The investment powder is weighed out
to ensure that the ratio of water to powder is just perfect.
The investment powder is then poured
into the mixing bowl with the water,
and it is all whisked together.
The texture should be nice and creamy,
almost like a nice pancake batter.
At this point, the mixing bowl is placed
on the investment table and covered.
When the motor is turned on, it acts like a suction,
and it pulls out as much of the air
out of the investment as possible.
After a couple of minutes,
the investment table is depressurized.
At this point, the lid is removed,
and the investment is poured into the flask.
Now, it is the flask's turn to be vacuumed.
The flask will need some time to harden,
so in the meantime, I'm going to pre-program
this burnout oven.
The furnace is programmed to ramp
and to hold at certain temperatures
to ensure a proper burnout cycle.
After a couple of hours, the investment has fully cured
and is ready to be placed into the oven.
At this point, I take the heirloom cross,
and I pull out all the diamonds that are in there.
We're going to be using the gold for the casting,
and the diamonds we'll be using later.
To ensure a clean casting, fresh 18 karat gold alloy
will supplement the gold from the cross.
And that cross is looking just a little bit big
for the crucible, so I pulled it out,
and I broke it into a few pieces.
Now that the burnout cycle is complete,
approximately 10 hours later,
the flask is carefully placed into the centrifuge
directly behind the crucible.
Now the fun begins.
It's time to melt down the gold and cast this ring.
The flame from the torch is directed
evenly around the crucible,
slowly heating up the gold
until it achieves melting temperature.
Ready, set, go.
The force from the centrifuge
sends the gold flying into the flask.
Once the spinning ceases,
the flask is then removed from the centrifuge.
It is taken over some water,
and during an oddly satisfying part of the process,
quenched.
Once the investment has been broken up,
I can now reach into the water,
fish around for that ring and see how it turned out.
Success.
Now it's time to take the raw casting
and throw it in the tumbler.
The tumbling machine is perfect
because it uses magnetic little pins.
These pins can get down
into all the nooks and crannies in the ring,
places that would be nearly impossible to polish up.
After tumbling the ring for about 10 minutes or so,
it's time to take it out.
And while it still looks dull,
it at least looks gold now.
The button is then separated from the rest of the ring.
This is the excess gold from the cast.
Next, I take a ring file to the spot
where the button was cut off.
This blends everything very nicely together.
A sanding disc is then used to smooth everything.
This is followed up by a steam cleaning.
For the center stone,
we'll be using a one carat lab-grown diamond.
This didn't come with the cross.
Rather, we'll be using two diamonds
from the cross as accent stones.
A heart burr is used to cut seats into the gold.
This is where the stones will sit.
The stones are placed and the prongs are tightened down.
Finally, it's time to set the center stone.
I'll use a setting burr to cut into the four prongs.
I'll then gently place the lab-grown diamond in the center
and take my stone setting pliers,
pull the prongs gently over the diamond.
After the stone has been set,
a file and a cut burr is used to smooth down the prongs
so they don't stick up too much.
The last and crucial step is ring polishing.
The ring is taken to a polisher
and it is buffed to a high polish.
This truly brings the shine out of the ring.
After polishing, the ring is placed in an ultrasonic cleaner
to remove all the polishing compound.
It is then steamed to a beautiful sparkle.
And there you have it, the completed ring.
Such a fun project to be able to take a family heirloom
like a cross and turn it into something
like an engagement ring that can be used
for many more generations to come.
