Wire Wrap Gemstone Hearts No Hole Crystals DIY Heart Pendant Beginner friendly Wirewrap Tutorial

Handmade Jewelry
2 followers
278 Video Views·May 11, 2026
AI Generated·May contain errors
Hey there, I'm Amrita from Arturia Jewelry and today we are going to make some crystal
heart pendants.
I have these beautiful jade rose quads and then this one tiny little amethyst heart and
I thought since it is February, let's make some wire heart pendants.
And if you've not already watched the video of the copper hammered heart pendant earrings
and adjustable ring, I will link it up in the cards and down in the description below.
And I'm going to show you a couple of different ways to do this.
Let's just pick out, maybe we'll do one of each of these.
So we have three of these going, three different sizes, different colors, different materials.
And as far as tools are concerned, it's my standard set of tools, a ruler, bent nose
pliers, needle nose or tweezer nose pliers, six step looping pliers, flush cutters and
a metal file.
For the first style, we're going to start with a really simple one and I'm going to
show you how you could take two lengths of 24 gauge wire and create a pendant out of
a stone that has no holes in it.
So I have two lengths of a foot each.
When I'm doing something abstract like this, it's nicer to take a longer length and then
when you cut off the pieces, you can save them for other projects.
We're going to line up the two wires and find the midpoint approximately, so that's approximately
the midpoint.
I'm going to hold it at the midpoint and separate my two wires and twist them three times.
So I have three twists on this side and I'm going to flip my wire over because I'm right
handed and I want to work with my dominant hand.
I'm going to put this point through just to see how much of a gap I need and that will
hold the bead and that will hold the stone in that gap, so I don't want it to be too
wide, about that much.
So maybe, let's see, that's about a quarter inch for my stone and I'm going to hold it
firmly against my finger and wrap this side three times.
That's going to create a gap into which I can pop the stone and that will anchor the
stone in place when we wrap it the rest of the way around.
That's how it's going to anchor our stone.
I'm going to hold the stone in place.
You could use tape and tape that in place if that makes it easier and then I'm going
to bring the wires on either side of the first curve of the heart and then cross them over
and twist.
So I'm holding it in place and I'm going to twist three times and I'm going to twist it
firmly so it holds the stone into that gap and there we go.
So that's one side attached and now I'm going to again separate these two sides and we kind
of want the twist to be on the side of the heart like that and then I'm going to cross
them over, move these out of the way, cross them over and twist three times.
So at this point I have created anchor points for the heart.
One at the bottom and we can adjust these to make it look to make the wires sit a little
prettier later but basically now my stone is securely in that wire so all that's left
to do is twist this up and make a bail and then we can adjust the wires later.
So I'm going to continue this twist up because I'd like a twisted bail and so I'm going to
hold these two and then twist them maybe about an inch in length and I'm going to do
the same with this other one and this is 24 gauge wire so it's relatively easy to do these
twists.
Take your time with it and then I'm going to bring these wires into the center again
and then twist these together so there we go and if you find it easier you can twist
the stone as you move your fingers up so the wires twist onto themselves and so there your
heart is in there securely in there and now I'm going to see which side I want facing
the front so I want this side in the front just because of the flex of the stone I like
that.
I'm going to pull this wire toward me and use the third step of my looping pliers to
hold the wire and then wrap it around the third step make a loop and then I'm going
to hold this loop and wrap all the wires around themselves a couple of times there we go and
then I'm going to snip the wires flush in the back and use my needle nose pliers to
tuck them in or you could use your bent nose too but basically you want the wires to be
tucked in so they don't catch anything I'm going to snip them a little closer I'm going
to tuck it in and then just run your fingers there look at it make sure all the wires are
tucked in and it doesn't catch anything so now my pendant is ready and I spend a few
minutes just going over and you know maybe straightening out any kinks and if you want
the curve to be more rounded you could use a round surface like a pen to just do that
to rub that against the wire and you'll get that to curve we can do that with these ends
too curve them a little bit and there we go we have a beautiful little rose quartz heart
done wasn't that easy very simple way to wrap a stone that has no holes if you're enjoying this
video so far please like share and subscribe and we will go into the next pendant and we're
going to use the jade heart for it and we're going to use the similar technique but change
it up a little bit for this one we're going to use 20 gauge aluminum wire we're going to cut
ourselves about eight inches of wire and I'm going to have two lengths and again we're going
to find that midpoint so around the four inch mark and I'm going to say four inches I'm going
to go over a little over a quarter inch to one side and wrap the wire for five times and then
we're going to separate the wire put the stone in because we want to make sure we get the right
size and then I'm going to do another five wraps and this is aluminum wire so even though it's
thicker than that 24 gauge copper wire it's pretty soft now this was how we started the copper one
two for the rose quartz but how what we're going to do different with this is instead of having
the wraps along the side of the heart we're going to flip it and so I'm going to stretch this out
to have the heart go in this way and have the wrap through the middle of the heart like that
so we're going to have the heart held in the center so that's how it's going to look a little
different from this one I'm going to continue twisting this one and with this I'm just going
to make one bail and not use all the wires so I'm going to twist this a little bit I'm going
to fold the front one toward the back and the back toward the front and then with my nail holding the
front in place I'm just going to straighten it because that's going to be the bail once we are
done with this wrap and then I'm going to wrap the back wire around the front one and then snip
it off and then make sure I tuck my wires in so I have my heart anchored securely in there and now
I'm going to twist this some more because I want the whole bail to have that twist so that's about
an inch and a half it's a little longer than we'll need but we're going to cut it off anyway
and I'm going to fold this wire toward the front again use the third step of my looping pliers to
make that loop around itself and then hold the bail gently this is aluminum wire so you don't
want to be too tough on it with your tools and wrap my wires around I'm just adjusting the wires
just to make sure it looks neat before I cut it off and I want to see how much of a wrap I want
do I want that knotted effect or do I want it to look a little more elegant and dainty I think I
like the knotted top and so I'm going to snip off these wires toward the back and use my needle nose
pliers to tuck them in and there we have the second heart done those are two styles of the heart what
do you think do you like them which one is your favorite do you like this style with the copper
wire or the slightly heavier style with a thicker gauge aluminum wire we're going to wrap this tiny
amethyst heart it has no holes and it is about half an inch in width and half an inch in length
so I have with me about two feet of wire I don't need the whole length it would be my need about a
foot but I already had this pre-cut so I'm just going to work off of that I'm going to fold the
wire in half and use the third step of my looping pliers to pre-make a bail so I'm just going to
wrap around that third step three times so one on each direction so it forms this coil of a bail
and then when it comes to the bottom I'm going to cross it over and start twisting it and that's
the bail formed so the idea is that we will have this pendant sit on the bail and then we'll have
the wires come up the front and maybe this will make a two-sided pendant let's see what you think
so if this is the back that's how the back would look one side would have those twists I'm just
going to go one more length I want to make sure that my twists are high enough to hold long enough
to hold the pendant and then I'm going to hold the pendant to itself to the wire like that and
bring one side up and wrap it around the bail just once just to get it secured I'm going to
bring the other side up go across and wrap that around the bail again and so now we have our heart
securely in its frame we can play around with the placement of the wire a little bit and then we'll
wrap that a few more times and cut those wires off I'm going to snip this one and tuck that wire
in and then wrap this around that the other way snip it off and tuck that in as well and then
just adjust the bail to make sure it's facing forward and if you feel like you have to go back
in and kind of make it circular you could do that and then this is the third type of frame
so you have this two lines going up the front and then you have a twisted back so today we
made three styles of wire wrapped hearts with no holes and so these beautiful stones have been
wrapped into pendants if you like this video please like share and subscribe and I will see
you in the next one have a beautiful day
