String Trimmer Head Replacement Made Simple!

DirtFarmerJay
309 followers
154 Video Views·Sep 13, 2025
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
We really enjoy having a string trimmer,
but eventually the head on the string trimmer
is gonna wear out and it's gonna come time to replace it.
Now this particular, what's called a quick load
replacement spool head from DeWalt
fits their series of cordless string trimmers.
Now on our particular one, we have the 922.
And if you'd like to see the review on it,
we've had this for five years.
You can check out the review in the links below
and see what we think about the tool.
But one thing I want you to notice right off,
and we've kind of taken this apart,
is that course is the head or the bump plate
that's on the bottom.
I want you to notice that this head
is larger in diameter than that.
So it's a little bit bigger circumference.
It still fits okay down here.
And it will change the speed a little bit on the hub
just because it's a little bit bigger around,
but just want you to be aware
there's a slight difference in size.
What we've done here is taken this apart
like we're getting ready to replace it.
So normally you would have this spool inside here,
this cover on the top like this.
You might have some of the old trim line that's in there
that needs to be pulled out,
but now you need to strip it back to this.
And when you do so,
you need to work on getting that nut off.
Let me show you how that's done.
All right, the trick to this
is stopping the whole shaft from spinning
so that you can use a large wrench
or even a vice grips to get off the nut out here.
The nut's quite large.
It's larger than 15 sixteenths.
So I found I need to use either a crescent wrench
or the lock grip pliers.
The first thing we're gonna do though
is stop this from rotating further.
There is an indent right here
on the main housing under the motor
and where the belt and all that runs over.
I'm gonna rotate around until there is a hole
which comes into view right there.
See it there?
I'm gonna rotate it back until it's in line with that
and then insert like a Phillips or in this case,
an Allen, excuse me, a star driver.
And I'm gonna put it down in there
and jam it back and forth
until now this won't turn any further.
Okay, now that you've jammed this right here
and it's not gonna rotate,
you're gonna turn this off in a clockwise
top to the right motion.
Now, if you can't use a large wrench,
the problem is you've got this all around it.
So I can't do flat.
I have to come in at an angle.
And if this is too, doesn't give you enough leverage,
you may have to get a set of locking pliers
to grip onto it, taking care not to put damage on us.
But let's go ahead and see if I can get this to turn.
Here we go.
Ah, there it goes right there.
So now I'm gonna spin that off.
And now you have the threaded shaft right there,
the way it is, okay?
This is all part of the old unit
and does not get used with the new unit.
All right, we have the old head off of here.
I remember it's a reverse thread.
So now we've got that off of there.
We're gonna go and pull this off.
And when you do, now's a good time to just clean out
what's in here using a soft brush or whatever.
A lot of little junk that's in there.
Get that cleaned up.
Go ahead and replace this back in the same orientation.
So it's lined up with a hole there and it's keyed on here.
So now that plate's right.
Now it's time to install this one.
Now this comes with this separate
and you might be tempted to put that on there
because it will fit on there.
But in reality, you have to put that keyed part into this.
And when you do so, that's gonna provide you the area
that allows you to wind up the trimmer line
around the spool.
All right, now that we've got that cleaned up,
let's go ahead and line up the hole there
with the area to jam this in, hold that in
so that it won't rotate.
And we're gonna go ahead and put this on.
It's gonna be a left-handed thread.
So I'm gonna rotate this way.
Pretty easy.
Bring it on home, just hand tighten it
because it's self-tightening every time you turn the unit on
and then we're gonna go ahead and pull this out.
And there it is.
The head is replaced.
That's your bump right here on the ground.
Line is through there.
Now the next thing we need to do
is go ahead and put the trimmer line in here.
Check out this video where we show you
exactly how to do that, how to thread it through,
how to wind it up, and a quick tip
on how to make it easier and faster
every time you need to do that change out.
Until the next time, this is Dirt Farmer Jay
enjoying a new trimmer head on my straight trimmer.
