A Victorian Chest of Drawers, Restored - Thomas Johnson Antique Furniture Restoration

Thomas Johnson Antique Furniture Restoration
41 followers
144 Video Views·Aug 15, 2025
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine restores this handsome Victorian chest of drawers. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, or write us at [email protected]. And for those on the East coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
I'm Tom Johnson, Thomas Johnson Antique
Furniture Restoration in Gorum, Maine.
Today's show is one of my favorite
videos. In it, I restore a V antique
Victorian chest of drawers. And this
video has so much information in it. I
reglue the case.
I rebuild the sides of the drawers. Uh I
show how to use epoxy putty and form it
before it fully hardens.
I also show how you can reuse the same
nails and nails that I leave in place so
that when I reassemble it, everything's
back in its exact original position.
My favorite thing is helping families to
preserve their treasures and their
memories. I hope you like it, too.
Please subscribe and share. I'd
appreciate it. Thanks. Enjoy the show.
This is a nice Victorian chest of
drawers. Uh it's all solid walnut. Uh
probably from the latter part of the
19th century and uh it's still it's
never been refinished. This is the
original finish. And that's good. I
think it can just be uh restored with
some oil and wax. And basically the
whole cabinet is just falling apart. In
fact, when it came in here, the first
thing I did was tape it together. And uh
now I'll carefully take the tape off.
And uh it also came with a lot of parts.
A lot of these are interior parts. Uh I
do have this part goes down here.
Basically I've got to take it completely
apart, put it back together again.
You can see on the back here
these light areas. So, there used to be
brackets that held an upper section. We
do not have the upper section. And
here's some writing. Kind of difficult
to read right now. We'll have to see if
we can figure that out later.
Bring
[Music]
up.
I really wish that I had found the
center board.
Well, I had noticed the chew marks on
the top of this molding here when I took
it off. This is completely chewed up.
Very strange.
[Music]
trying to figure out, you know, what
holds this together. And I see that
there's nails here. These are original.
They're the old square cut nails going
in this way. And I also see nails this
way.
I think maybe I'll work these side
panels off uh before I disassemble this.
So, I've got perpendicular nails here.
I'm tapping this.
Sometimes if you can get this to back
out a little bit
and then
hit it back in, the nail will pro
protrude enough so that you can get it.
Uh I'm kind of going this way, hoping
that this nail might be the smaller nail
might bend and allow this to come apart.
And uh that doesn't seem to be working
too well. But I can also just worry this
thing.
[Applause]
Worry it. worry at trying to get
something to give here.
Starting to see this uh opening up a
little bit here.
Wow.
It's just what I was hoping for. And
yeah, you can see that these these nails
that went in through the front bent
over.
The nails that were through the sides
are intact and I can leave them right
there.
I'm waxing the edges of these p these
panels so that they remain
free floating.
I don't want any glue to get on.
All right. This is the other This is the
other side.
And I've already noticed
that there's a piece of wood missing.
There should be a piece of wood right
here that, you know, makes up the cheek
for the other side of this tenon. So,
I've got to cut this out. Put a new
piece of walnut in there.
Heat. Heat.
[Music]
And I should be able to glue this new
piece on while I'm gluing up the whole
panel.
So, I've got both sides uh glued up now,
so we can glue up the entire case. And
I'm uh getting my cross pieces here uh
and
figuring out where they go. They're all
marked. And this is the second uh cross
rail in the front. And uh it's got a big
chunk of wood missing. It's kind of odd,
but I've got to repair that before I do
anything else.
[Music]
[Music]
[Music]
[Music]
Heat up here.
[Music]
Happy
heat.
[Applause]
[Music]
[Music]
So, while that uh carcass is drying,
I'll check out the drawers.
Boy, they seem uh remarkably tight.
I think this
This drawer is good.
And the drawer sides don't look terribly
worn either.
Now, this drawer, this must be the top
drawer.
The drawer sides here are badly worn.
as much as I can. I like to use the uh
the old nails, the same nails that I
took out of here.
Now, this bottom board,
not sure how it was attached.
I think that I'm going to take these
blocks off. These definitely aren't
original. And I think I'll glue this
into place for what it's worth, but then
I'll add larger blocks uh underneath
this.
I remember now cuz I had taped this nail
and one of the ways that this back rail
was held in place was they had a nail
right through the outside of the
cabinet.
This is the same nail. I'll put it back
where it was. And um if I don't have the
original nail to use, I have a pretty
good collection of uh old nails and new
nails that uh I buy from a company
that's been making these nails since uh
1820. So it's with the same machine. So
it's uh even conceivable that these
original nails could have come from the
same company from which I buy
replacement nails.
So now I've got to fit the uh drawer
runners and drawer guides back where
they belong. The ones that were here I
marked.
Others I can uh I'm able to determine
where they went by matching up the the
glue blocks.
This is the molding that uh came across
the front of the cabinet between the
first and second drawers. It's all
chewed up. I'm going to repair this with
epoxy putty.
Now, as this hardens, after just a about
3 minutes here, maybe five minutes, you
can start to shape it a little bit with
a little bit of water on your knife.
[Music]
I think I'll leave the line until I uh
try it out.
So, now I've got to sand my putty on
this molding.
Uh this uh this molding sanded up fine.
It doesn't look like nearly as many
teeth marks in it as before. There's a
some kind of strange adhesive on the
back. It doesn't want to scrape off, but
I think heating it up will uh I'll be
able to get it off.
All right. I'm going to brush a coat of
shellac on this molding.
All right. While I'm waiting for a few
things I've glued to dry, uh, got to
address the marble here. The marble's
not in bad shape. I mean, it's not
cracked or anything. It is missing a
chunk in this corner, but it's basically
just u kind of dirty. Uh, and so I'm
just going to clean it. There's not
really a lot you can do to marble.
There's a lot of uh lot of information
online and different things that you can
do, but basically all you really can do
is clean it. Then maybe I'll wax it. Uh
so I'm going to mix up a very mild
solution of Dawn detergent with just a
splash of bleach in it.
Well, this really did uh clean it well.
Really brightened it up. It's funny that
first uh little rust mark when I hit it
went away almost instantly. Uh these
marks and one over here uh unfortunately
aren't going away instantly, but we'll
let this sit for a while. See what
happens.
Okay, so I've still got this uh
baseboard to glue on. And I have uh a
bunch of glue blocks.
Got to figure out where they go. And I
might make new make new uh blocks for
the back of the bottom here.
[Music]
I've got these three nails I can line up
in the same original nail holes there.
All right, the shellac on that molding
has dried. So, I'll glue this down now.
And I also left, you know, some of these
old nails here, and I'll put them right
back where they belong.
Upside down like this is a great way to
uh easily see where all the glue blocks
need to be.
A lot of glue blocks stayed in place
during the disassembly and then
reassembly.
But other places,
like these corners here, you can see
where there were glue blocks
on the bottom of the case here, I've
made four new corner blocks, and I've
made them big enough that uh they could
accommodate casters should we decide to
put casters back on.
Wow. That's the first time I've tried
this drawer.
Worked pretty well first time out. I
don't think that's ever happened before.
I'm going to wash this down now with a
mild solution of Murphy's Oil Soap.
I'll use a gray Scotch-Brite pad and uh
just try a small area first.
Yeah, I think it's doing a good job.
Okay, I've got a few things to do here.
This top drawer is missing the
discussion.
I need to uh fit the drawers. make sure
they work correctly. Uh, install drawer
stops and put the back on. I have this
memory of uh, buying wooden discussions
a long time ago.
There they are.
Yeah, that'll work fine.
>> I made new drawer stops, which are just
blocks of wood. Uh, on this cabinet,
it's unusual. The drawer stops are glued
to the unders sides of the rails.
So, this top drawer, it's still got a
lot of uh these scratching and bite
marks in this corner. Uh, which, you
know, corresponds to this corner that
I've already, you can see I've already
puttied up a lot of the tooth marks
there. This is more scratching. There's
some wood missing here. I think I'm just
going to have to uh fill that with some
uh wood putty.
Okay, the putty's dried for a couple
hours. Now I'll sand with 150.
[Music]
You know, I'm trying to do as little as
possible to the to the surface of this
piece of furniture. Uh but there's
always something. And in this case,
there was these really bad scratches
here. There's scratches across the
front. Now, this area was also badly
chewed, and I filled that and sanded it
just with 150 and then 220. It seems to
be retaining the same color. It looks
good. So, I'm hoping that the draw will
be the same. I'm not trying to get all
these scratches completely gone. I'm
hoping that when I recote this, uh,
they'll blend in.
I'll be able to find four casters in
here.
[Music]
I'm going to uh put some stain on the
new wood. These new blocks,
[Applause]
the new blocks and the new wood that I
put in that rail there.
I can see that that uh patch I did on
the rail may need something stronger
than a oil stain. I may have to hit it
with die stain
after sanding that top drawer. So, you
know, I sanded it with 150 because of
all the defects. I sanded the other
drawers, too. And now I'm just going
over the whole piece just with 150, just
real lightly. Just looking for any
problems.
[Music]
I'm going to give it a coat of this
satin tongue oil varnish. Uh, you know,
it's an oldfashioned type varnish. And,
uh, this piece, there's no way of
knowing what was on it originally, but
uh, you know, it's like from 1865, 1885,
and may very well have had a similar oil
varnish on it.
All right, this has dried overnight. Um,
you know, I was really hoping just to
give it one coat and then wax it, but it
has soaked in so much. I'm going to sand
it with some 320 and give it another
coat. Before I do that though, I've got
to stain uh some more new pieces of wood
also.
[Music]
That second coat really did the trick.
It looks nice and even now. It's got a
few little knits and stuff on it. I'll
go over it with the 40 steel wool and
the orange oil beeswax polish.
Okay, now uh I've got to install the
back.
It's funny. When I took this back off, I
thought there was a piece missing, but
some of these boards were split. Now
that I've glued them back together and
put them in here, I can see that there
wasn't a board missing. These two boards
overlap each other. They don't have a
strip like this between them.
Well, there we have it. This is a nice
little Victorian cabinet. Uh the owner's
grandparents brought it over from
Ireland. Uh we think 1865 to 1885,
although I think probably the latter.
These this hardware is a East Lake
design, which is the 1880s.
And I've ordered a new piece of hardware
very similar, but it hasn't come yet. I
apologize for that. But if you remember
what this looked like when it came in,
it was just completely falling apart,
held together by tape. I rebuilt it. I
really like doing a minimal restoration
like this where I just cleaned it and
recolored it with a couple coats of
tongue oil varnish. I think it looks
pretty good.
