Honda PCX Brake pads and shoes change (with rear wheel/exhaust removal)

Two-Wheeler Technology
5 followers
#pcx #scooter #honda
A guide on how to replace your Honda PCX 125 brake pads and shoes including removal of rear wheel and exhaust
Hey guys, welcome back to another video and today we are gonna be replacing the
brake pads on this Honda PCX. I believe it's a 2019 model, it has a missing caliper on the front
and it has drum brakes on the back. We have our brake pads and shoes ready here.
As usual servicing the PCX is pretty much straightforward and very easy.
So let's go ahead and start removing the front brake caliper by removing
these two holding bolts here which are 12 millimeters.
Now that the caliper is off we can remove the brake pad holding pin which is this one.
You can use an 8 millimeter spanner or socket.
And once that pin is removed you can just pull out the old brake pads. As you can see
they are extremely worn out. The old brake pads, there's barely any friction material left.
So next step is to clean up all this brake dust from the caliper and push the pistons back inside.
So I'm gonna be using some brake cleaner to make sure that the pistons are nice and clean.
I'm gonna be using this vise to push the pistons back in.
So now the pistons, both of them are flush with the caliper. I've also removed this bracket.
You can clean up these pins also and give them some new grease.
They will sit just right here, these rubber boots. So let's open up our new pads.
Also don't forget to clean up this brake pad pin. If there's some rust here make
sure you clean that up and also grease it a little bit. So the brake pads on the PCX
are a bit different. One of them has this piece over here which is gonna sit on a pin.
So let me show you. So this one would be a touch bracket. This is gonna sit on the outside and
this is the pin that is gonna be holding it. So that's how it will sit on the outside.
And the other one is gonna be on the piston side, so on the inside.
So what I like to do beforehand is just add a little bit of copper grease on the pins
and a bit on the back of the brake pads itself, just so they don't get stuck to the pistons.
Just a little bit is fine, no need to go overboard.
That's it. Now once the pads are in position you have the holding pin. Make sure you have cleaned it
and lubed it up a bit. I use copper grease on this.
I'll pass it into the caliper and make sure it passes through both of the pad's holes.
And just tighten it back.
So now our pads are secured inside the caliper and it's ready to go back in on the bike. Don't
forget to put a little bit of Loctite or Threadlocker on the caliper bolts so they
don't get loose with vibrations. So make sure you torque these down to 30 Nm, the front brake
caliper bolts. And one last step before we finish off is to pump a bit the front lever
so we can set the pistons because the first few pumps are gonna be really soft until the
pistons adjust like this. So now the pistons are adjusted and the brakes are ready to be used again.
So now that the front brakes are done we're gonna move on to the rear set which are brake shoes and
not pads which basically complicates things more because we need to remove more stuff to do that
because we have to remove also the rear wheel as the brake shoes sit here in the middle of the rear
hub. Now to do this we have to remove the exhaust, we have to remove this wing arm,
part of the mudguard, these two bolts and also the rear shock. First thing we're gonna do
is remove the exhaust which is held on by three bolts here, one, two, three and also two 10 mm
bolts on the engine side. I will try to show you where they are. So these are what the two 10 mm
bolts look like on the engine side. Remove the exhaust. Ideally you're going to have a quarter
inch socket with an extension and a 10 mm deep socket. So let's start removing those two 10 mm
bolts first. Now unfortunately I can't really fit my camera inside here, so I'm just gonna
remove the 10 mm bolts now. So these bolts are 14 mm and that's it, our exhaust is now off.
So now without the exhaust which we have much more access to everything here,
so now we're gonna remove the swing arm bolts, 14 mm, we're gonna remove these two 10 mm mudguards
and this 12 mm shock absorber bolt. So actually I'm gonna start with the driveshaft nut here,
that's much easier to remove when everything is still assembled. Now this will turn with the wheel
so we're gonna have to hold the rear brake so the wheel doesn't turn. I'm gonna do that
with some cable ties holding the rear brake lever. So let's do that.
So this is how it looks, the rear lever is now fully depressed
and we should be able to remove the driveshaft nut.
So
now don't forget we have to release the rear brake now so we can loosen the whole assembly.
So let's cut the cable tie that we approached earlier. Now this swing arm should simply slide
off. So there will be a spacer here, do not lose it. Now we should be able to remove the rear wheel
also. So our rear brakes weren't as much worn as the front ones, as you can see there's still a bit
of meat left. But now since we disassembled everything we're gonna attach the new brakes
anyways which are here. These are Ferodo, this is the box, this is the model number, it comes also
with the springs included. So let us start removing the existing pads. So simply pull
them out and this will remove the tension from the springs which makes it easier for us to remove
them. So don't forget how they were installed, like this, as we have to do that in reverse order now.
So before we install the new shoes we're gonna give it a good clean with some brake cleaner.
Now I do like to add some copper grease on the friction parts which will be this pin
and this pin here. So I'm gonna add some copper grease over there.
Now what I'm doing is assembling the springs on the new shoes. So this is how it should look like,
like this. Springs on the shoes and now we just do it in reverse order. So
place them into position, split them a bit apart until they fit inside
the brackets. And our shoes are now properly installed. So now if the wheel doesn't fit
because of the shoes, you're gonna have to slacken a bit the rear brake adjuster
on the other side. So let's do that right now, let's slacken it out.
So
now that everything is assembled on the other side, the one last step that we have
is to properly adjust the tension on the brake adjustment. So we're gonna do this by rotating
the wheel by our hand and make sure that it spins freely. Start tightening this screw here
and once the wheel starts to drag, just like this, look it's not turning freely anymore,
you turn it back one step. I'm gonna do another step back and now the wheel turns much more freely.
And that is how you adjust the rear brake. So that is the job done, unfortunately
since the rear wheel is still with shoes and not brake pads and discs, it increases the time of
this job by a lot. But yeah that is unfortunately how it is with Honda Office EX's, so we have to
accommodate for that. If this video has helped you, please like and subscribe to the channel
and I will see you on the next one.
