Honda Civic Mechanical Review

The Auto Geek
46 followers
102 Video Views·Oct 18, 2022
Today we're going to be taking a look inside the Honda Civic to see what's inside and how it works.
Now we're going to start by taking a look under the hood of the Honda Civic. This one is the
turbocharged model which means that it has a 1.5 liter four-cylinder engine here situated
transversely for front wheel drive and then over here on the driver's side we have a continuously
variable transmission. Now we're going to start by taking a look at the air intake system on the
Honda Civic. This being the turbocharged model it's a little bit more intricate than a naturally
aspirated engine. Air is going to be drawn from underneath the hood down into this vent over here.
It's going to be sent down inside of a resonator box and then come up through this air filter.
The air filters are going to pass by a mass airflow sensor and then head over here to the
turbocharger. Now Honda did make some changes to improve the efficiency of the turbocharger but you
can see where this air inlet here bolts directly to the turbocharger. It's then going to be sped up
by the airflow coming off of the exhaust over here. The exhaust itself is going to continue
down into this catalytic converter and the pressurized air is then going to head down through
this pipe into your air-to-air intercooler at the bottom. That intercooler is located at the bottom
half in front of the radiator. You can see that through the grille here and that's going to help
to cool down some of that charged air that was warmed up by the exhaust gases. Now from underneath
the vehicle you can see here's where the pipe comes off of the turbocharger and goes into the
intercooler in front of the vehicle in the bottom of the radiator area. It's then going to get cooled
off and then sent through this pipe over here which is your charge pipe which is going to go
up and over the transmission. The pressurized air is then going to head out through this plastic pipe
over here and then out to the back here where you have a drive-by-wire throttle body that's going to
regulate the amount of air going into the air intake plenum which is this plastic piece over
here which is ultimately bolted to the head and feeds the boosted air into the engine. Next we're
going to take a look at the fuel system on the Honda Civic. You can see we've got this fuel line
over here kind of dangling loose. That's going to feed fuel over to this high-pressure fuel pump.
That's because this engine only has direct injection. You can see underneath this little
sound deadening here is where the high-pressure fuel pump lives and it's going to be driven off
of the intake camshaft at the back here. The high-pressure fuel pump is going to send fuel
down underneath the fuel rail which is underneath the intake manifold. You can't really see it,
there's a little piece of it sticking out over here, but that is essentially going to inject
fuel at very high pressure into the combustion chamber. Now of course the disadvantage of having
direct injection only is that you might have to clean the intake ports periodically because you
don't have that gasoline injected into this airstream before it goes into the engine. Now
taking a look at the top of the engine here you can see we've got our four ignition coils and
that's going to make for very easy spark plug changes. Over here we do have a plastic valve
cover and this engine takes 0w20 weight oil with a dipstick located over here. Alright so here we
are underneath the Honda Civic and you can see over here on the passenger side we've got the oil pan
and this blue oil filter. Then over here on the driver's side we've got the transmission pan. Now
taking a look underneath here we do have a metal alloy oil pan. Here we've got the oil filter which
is pretty easy to access once you remove that closed up panel that was underneath here and
here's the drain port. This setup should make for some very easy oil changes once you've got that
panel removed. Now from underneath here just in front of the oil filter we've got a better look
at the AC compressor as well as the drive belt down from here. Now the PCV system is very simple
with just one valve that comes straight off the valve cover and goes right into the intake although
it goes right before the turbocharger so it could probably gum things up if you burn oil. The Civic
has three main engine mounts you've got two on the top here one on the transmission side you can see
it underneath the battery here and one over here on the engine side. Now down underneath here we
do have our third engine mount that is mostly a torque mount to control the sway and the body of
it is made of a rigid plastic. Now taking a look at the front part of the engine here on the passenger
side down underneath this engine mount is actually the timing cover and underneath that timing cover
is a timing chain so that means that this engine does not need to have a periodic timing belt
service. Over here we've got the exhaust camshaft and on this side we have the intake camshaft.
Now both of those camshafts have variable valve timing control through a VTC system for cam phasing.
In addition Honda's also added a VTEC system to this generation of Honda Civic which adds a
variable lift system the way the old cars used to on the exhaust side only you don't really need it
on the intake side because you got a lot of air moving in with that turbocharger. Now just in front
of that timing chain cover is the drive belt setup you can see there's a single drive belt
we've got the crank pulley down at the bottom there and then at the back here it's easy to make
out the alternator then over here this guy is your auto belt tensioner it's actually a hydraulic
tensioner. Now moving over here to the front of the engine that belt is going to come around to
the water pump which is over here and then the AC compressor located way down below over there.
Unfortunately accessing some of these components is really difficult if you need to change the
water pump on one of these cars the manual actually requires you to remove the turbocharger
just because it's so close to it in order to get to those bolts and then kind of snake it around
these lines to get it out. In addition getting to the alternator although it's pretty easy to access
at the back here requires you to remove the exhaust pipe over there and snake it down underneath the
bottom just because you can't get it up the top here it's pretty difficult to work on. Now from
underneath here you can see this is the alternator and its bracket that holds it in once you get it
out you will have to remove this exhaust pipe over here and kind of snake it out between here
and the subframe. Here's one thing I don't like the washer tank here is actually buried inside
of the fender just like German cars so maybe if you tap on this fender you could crack your washer
tank but even worse than that is this little hose that comes out from here seems kind of weak and
you could bend over and probably break that. This hose over here seems like an afterthought because
they've just put this piece on top of here after a while that could wear down and break. Now taking
a look at the continuously variable transmission looking over here you can see we do have our dip
stick for your fill port when you do have to change your transmission fluid at least they
mark that and make that nice and accessible without removing anything. Now if you follow those two
coolant lines you can see it goes to a heat exchanger it's actually a transmission fluid
temperature warmer that helps to warm the fluid to optimal levels when the engine is cold and it
also helps to cool it down if things are getting too hot. Now inside of there actually houses the
transmission strainer which is what's going to strain out any excess particles that get stuck
in the system. In addition to that fill port it looks like I found another fill port located over
here at the back of the airbox. Now taking a look at the transmission from underneath all you got
is a drain port for this transmission pan this does have a traditional transmission pan which
holds the fluid inside and that's pretty much it you've got the axles up at the front here which
are going to come out of the transmission to drive the front wheel. Now just above that axle
you can see here we've got the starter motor it lives in a really tight spot here so accessing
is pretty difficult you will have to remove this exhaust pipe and good luck with that when this
car gets old and rusty. Now looking at the Civic suspension setup you can see we have a two-piece
subframe here the back part of the subframe here where your steering rack mounts to is actually
made of aluminum whereas the front part here that comes up to the front is made of a stamped steel.
Now looking at the suspension setup from underneath you've got our sway bar link over here
we do have a stamped steel lower control arm with a bolted on ball joint over here then from the back
here you can see the knuckles are actually made of steel. Now unfortunately changing bearings on
one of these means that you're going to have to take it to a press because there's no bolt-on
bearing here it's a Preston design. Taking a look at the front suspension on the Honda Civic here
you can see we've got a McPherson strut front suspension here with the coil up top and the
shock absorber over here the shock absorber attaches down to the steel knuckle over here
using a single pinch bolt. Now one thing I don't like about this pinch bolt design is that the
strut has to sit inside of this steel knuckle here and when it comes time to change your strut
this often gets rusted inside of here. Now the front here you can see you've got our sway bar
link that mounts up to the strut over here and then down at the sway bar way down at the front
here. Now looking around the suspension you can see down over here we've got a stamped steel lower
control arm and that's going to mount up to the subframe over in this location here. Now replacing
a control arm is a little interesting here because you do have this bolt for the front bushing
now if you back this bolt out enough you're going to crash into the sway bar so you might have to
disconnect that and swing that out of the way. The back here is your standard Honda bushing that's
just bolted up to the subframe. Now over here from the side you can see this is the aluminum piece
of the new subframe that they've made whereas the front part over here is actually made of
stamped steel so they've actually used both materials together to form a subframe. Now in
addition here we have our inner and our outer tie rods that mount to this knuckle and here we are
looking from the bottom here where you can see the bolted on ball joint where it bolts onto the
knuckle over here. At least they've still kept this a separated piece as opposed to having an
integrated ball joint so you can change it separately. Now taking a look at the rear
suspension on the Honda Civic you can see we've got a multi-link setup here the upper control arm
kind of bolts up to this subframe and comes over to this aluminum rear knuckle. Over here we've got
three bolts that bolt on your control blade which is going to bolt up to the body itself.
Then at the top here we have our shock absorber and looking at the back here once again we've
got our shock absorber that's going to mount down to this lower control arm here which is actually
a bed pan it's a stamped steel lower control arm and this one's got the spring here that's
going to attach straight up to the body and then over to the subframe at the back there. So looking
around the rear suspension here you can see if we come in here a very small stabilizer bar link
that mounts to that lower bed pan arm and then it goes to the sway bar which is going to go over to
the other side. Our subframe here is actually made of stamped steel unlike the front where it's an
aluminum and stamped steel composite. You can see this here is our lower lateral link it's going to
also bolt to the subframe and that's going to bolt down to the knuckle at the bottom here. Now here
you can see where that arm is going to bolt to the knuckle. The knuckle itself is made of aluminum
this here is where your shock absorber is going to mount and then of course your bed pan arm at the
back here. Now that front arm is going to go up here and mount up inside of the body cavity over
here and for all you guys who like to camber out your Honda Civics i found the cam bolt over here
it's actually part of this lower bed pan arm that holds the spring and here's another look at this
little tiny stabilizer link it's so short just fits in between here and then this here is a sway
bar again this diameter is pretty small so definitely could upgrade that if you want to
improve your handling. Taking a look at some of the electronics underneath here we do have our
fuse box which is pretty easy to access right at the front here over here we've got our battery at
least that's not buried in the fender or something and over here we have the ecu now one thing i
don't like about the ecu is right up next to the front of the vehicle so if you do get into an
accident it's pretty easy to damage and expensive to replace. Now taking a look at the cooling system
on the Civic you can see you've got a radiator located right at the front here as well as the
radiator fans down here and the radiator cap it's pretty easy to access and work in between here
there is enough room to get my hand in between here to get things disassembled however in order
to change the radiator out you do have to remove the front clip of the vehicle including the front
bumper so that makes for a lot of labor and here's a look at the back of the radiator from underneath
you can see we've got dual cooling fans at the front here now the basic cooling setup starts at
this junction over here we've got our upper radiator hose it's going to go into the radiator
the lower radiator hose is going to come down over there and be sent into the engine through
this thermostat which is in this plastic housing and then it's going to circulate through the engine
remember we do have the water pump up at the front here which is what's going to circulate
everything it's just a mechanically driven water pump then you've got the coolant jug located over
here another thing is this radiator support is made of a composite plastic which is nice and
structurally hard however if you do get into a minor collision in the front and this cracks
then you're going to have to replace the entire thing you can't really bend it back like metal
now looking at the exhaust setup on the Honda Civic you can see we've got the integrated exhaust
manifold but Honda's made some changes here by pairing off cylinders two and three and one and
four separately so they're not fighting each other as if they would in a single port here you've got
your air fuel sensor it'll be then sent down over here to the catalytic converter area but before
it does that it has to pass through this turbocharger and turn that compressor wheel
here you can see we've got our oil lines that go to the turbocharger and over here you've got
our intake side which is what pressurizes the intake air going through that charge hose over
there now the exhaust gases is going to head down through this catalytic converter and then down
underneath the engine to the back now looking at the catalytic converter and the exhaust from
underneath you can see we've got a flex pipe over here then it's going to go up and over the subframe
and then towards the center muffler continuing back from the exhaust setup you have your mid
muffler over there on this model it's got dual exhaust which is where it splits out over here
and it goes to a muffler over on this side and then one over on this side now taking a look at
the braking system on the Honda Civic you can see we've got a traditional brake master cylinder over
here with a brake reservoir the brake booster itself is just your typical vacuum driven brake
booster however because this is your turbocharged engine the manifold pressure can vary as well as
a start-stop system so they've come up with putting a vacuum pump located over here
electrically driven and that vacuum line is going to run all the way over there in order to power
that vacuum pump now that brake booster's got lines are going to come over here to the abs module
which is going to control the traction stability control and any autonomous braking features on
this vehicle now taking a look at the brake setup on the Honda Civic is fairly straightforward we
do have a floating caliper design with a single piston inside and we've got our disc rotor that's
ventilated up at the front now taking a look at the rear brakes on the Honda Civic they are
disc rotor they don't have any drums anymore and it is on a floating caliper design over here
one thing i notice is that they actually use only a single rotor screw anymore before the
older Hondas used to use two rotor screws i wish they would just get rid of both of them because
when they rust out or stripped out they're pretty difficult to get out in addition we do have an
electric parking brake there's no more mechanical parking brake on this and here's where the motor
is going to sit now looking at the steering system on the Honda Civic this uses a dual
pinion steering system so you've got the normal driver steering shaft that comes down to manually
steer the car on the driver's side then over here on the passenger side you can make out the
electric power steering motor that sits on the rack on its own pinion on this side and here's
a look at the fuel tank it's actually made of plastic now if you go further up inside of there
you can see the evap canister and that's pretty much a look under the hood and underneath the
new Honda Civic make sure you subscribe if you want to see more videos just like this one
