How To Cut Deep Mold Cavities With Pencil Lead
Aug 5, 2025
What's up guys, I'm over in the EDM department
and today I've got a very interesting project.
We're gonna be cutting an electrode out of graphite
that's 50 thousandths wide.
Now this is the same material that's used
inside of pencils every single day.
After we do that, we're gonna take it over
to our sinker EDM, we're gonna burn a pocket
with square internal corners two inches deep
into a piece of hardened 420 stainless steel.
For those of you non-EDM folks,
this is essentially like taking a pencil tip
and plunging it into a piece of steel two inches deep.
All right, so let's get it set up.
Boom.
So first things first, we're gonna install
our adapter plate from AROA
and then we're gonna indicate this surface in parallel
with our Y axis so that we can bolt our quick chuck
to this adapter plate.
I'm only gonna tighten down one side for now,
it's gonna give me a pivot point
so I can indicate this surface.
Not bad for a Monday.
All right, we went ahead and indicated everything
in within a tenth.
We're gonna go ahead and tighten down our bolts
and then we're gonna check it one more time
to make sure nothing moved when we tighten down our bolts.
All right, we're happy with that,
so we're gonna go ahead and take our indicator off
and then we're gonna install our AROA quick chuck
onto our adapter plate.
What this is gonna do is it's gonna hold
our electrode holder and our graphite suspended
out into the EDM tank so that we can cut the profile
of our electrode.
Now we absolutely love sharing free education
with all of you.
We just released a Titans of CNC Grinding Academy.
To access that, go to grindingacademy.com.
You can watch hundreds of free tutorials,
learn all about the world of CNC grinding
and take your career to the next level.
So now we've installed our graphite blank
into our electrode holder.
One thing to pay attention to is our graphite
actually isn't sitting in the center of our holder.
You can see we have a gap here and we also have a gap here.
So we can't pick up off our electrode
because then it's gonna be offset
how much it's offset in the holder.
So we're gonna put this into our fixture.
We're gonna find our Y center point
so that this is cut on center with our holder.
So I just removed our ground standard
that we used to find our Y position.
I just installed our graphite electrode into our holder
and we're gonna touch off on the end of that
to find our X location.
So our wire just touched off on the front face
of our electrode blank.
Instead of setting X to zero,
we're gonna set it to X of positive 55,000.
That will make sure that we cut into our blank
by 50,000 when we run our program
plus 5,000 for half the diameter of our wire.
All right, guys, our setup is complete.
That's enough talking.
Let's hit start and cut some graphite.
All right.
All right, guys, so our first operation is complete
and our machine has moved to the next thread point
and stopped.
At this point, we're gonna pull out our slug
that was cut off during our first operation
and we're also going to index our electrode holder
in our quick chuck for the next op.
Now, the only reason we can do that
is because we're working off the center
of our electrode holder.
So we can index at 90 degrees
and we'll still be on location perfectly.
All right, guys, so our roughing electrode is finished.
As you can see, it's a very, very narrow rib electrode.
This would be really difficult to manufacture
on a mill or on a grinder.
You need diamond coated tools,
might create a lot of dust.
With the EDM, we get to remove all those factors.
I wanted to take a second to talk to you guys
about the programming strategy
behind how we cut our electrode.
This slug was essentially attached just like this
before it was cut.
Now, when we cut this,
we started from this side of our electrode
and cut in this direction and out.
The reason we did that
is because when our slug is attached,
if we were to cut from this direction and out,
graphite is very brittle.
What could have happened is as we cut,
our slug might wanna try and do this
and then right at the end,
it's gonna wanna break off.
And that would leave a little bit of a chip
right at the tip of our electrode,
which we can't have.
To fix that, we came from this direction
and now if it chips,
it'll chip down at this portion of the electrode,
which really doesn't matter at all.
For this burn, we're gonna need two electrodes.
So this is only our roughing electrode.
I'm gonna load another piece of graphite into our fixture
and cut our finishing electrode.
And then we'll head over to the sinker
and we'll set up for our burn.
Burn.
We?
All right, so our finishing electrode is done.
We now have a rougher and a finisher.
I can't stress to you guys enough how impressive this is,
this is 50,000 wide graphite,
which is the same material that's used in pencils.
And I know you guys know how easy it is to break a pencil.
We're gonna take this,
we're gonna burn it into this hardened piece
of 420 stainless steel.
We're gonna go two inches deep.
It's gonna be insane.
So let's go over to the sinker and make it happen.
So we probed our work piece
and we found the center point of that.
Now we're using our head probe
to probe the center point of our table probe.
What that's gonna tell us is
the exact center of our C-axis.
After that, we're gonna load each electrode in
and we're gonna probe the square pad
around the top of the electrode.
And it's gonna give us the difference
between the center line of our C-axis
and the center line of our electrode.
As that first electrode goes all the way down
into our pocket, it's very narrow
and it's a very deep burn.
So the electrode's gonna wear
throughout that entire process.
So we're gonna come in with that second finishing electrode
and we're gonna use that to sharpen up those corners,
make everything nice and crisp and perfect.
For this burn, we're using a 10,000ths per side spark gap.
Now we're executing this burn with no additional flushing.
As that electrode gets deeper and deeper into the pocket,
it's gonna become more and more difficult
to evacuate the swarf created during the burn.
And that's where the 700 inches per minute retract
of our Z-axis is important.
What that's gonna do is it's gonna help
pull that fluid out and pull that swarf out,
as well as when it enters the cavity rapidly,
it helps push all that EDM swarf out of our pocket
so it's clear for the next burn.
We don't have any short circuits
or buildup of our EDM swarf.
Now this is what we call a rib burn or a rib feature.
What that means is in injection mold making,
it's very common to have molded parts
that have ribs around them
to reinforce the strength of that part.
But in order to do that,
you have to have a rib slot burned into your mold insert.
All right guys, so our burn just finished up.
The internal corners look nice and sharp
and the wear on our electrode appears to be very minimal.
But I'm really anxious to see
what the inside of our part looks like,
so I'm gonna break this vice loose
and show you guys how it turned out.
As you can see, our rib electrode burned
two inches deep into these pieces
of heat-treated 420 stainless steel.
And to me, the results speak for themselves.
I mean, this is crisp.
Look at the sharp internal corners.
We finished it with a 24 VDI on the surface.
Very happy with how our Iris 6 Synchro EDM performed.
This is exactly the result we were hoping for.
It just goes to show,
in manufacturing you can do absolutely anything
if you have the right technology and the right equipment.
So to be able to burn a 50 thousandths wide blind pocket
into 420 stainless steel that's been heat-treated
to 45 Rockwell is absolutely amazing.
Our synchro handled it with no flushing
absolutely beautifully.
The results speak for themselves.
The other day, we got this pallet in from Shunk.
It's an absolutely massive electromagnetic chuck.
Check this out.
We're gonna be installing this magnet
on our Iris 6 Synchro EDM in an upcoming video.
You don't wanna miss that.
If you like what we're doing,
don't forget to like and subscribe
and we'll catch you guys next time.

