德拉克講海軍歷史 在(無畏艦,一戰,二戰時期)各國海軍是如何修理受損戰艦的(原視頻無字幕)
王者风范
22粉絲
12 次觀看·2025年11月30日
Hello everybody and welcome to another Wednesday video
This week we're going to be going through the stages of repairing a damaged warship
This was voted for by the fine folks over on Patreon
And well, it's not possible to encapsulate every single way of repairing every single form of damage to a warship
And for the period the channel covers, the operations to do so could vary wildly
Considering we're talking everything from pre-Age of Sail all the way up to the end of WWII
But based on the most commonly covered ships on the channel
We're going to look at the repair of a damaged warship from roughly the WWI, WWII period
So the Age of Steel, the Age of Steam, the Age of Dreadnoughts
And we're going to assume that the ship is a relatively basic gun-based vessel
So a large cruiser or a battleship
There are a few minor differences that would occur with things like aircraft carriers
And also at the smaller end with things like destroyers and sloops
So this seems like a comfortable medium in which to sit
We will of course make reference to a few carriers and smaller vessels that were damaged
As case studies or minor details
But primarily we're looking at your standard WWI, WWII vessel
And a lot of the notes for this are actually taken from the damage repair
And then subsequent refit notes for HMS Belfast
Which is actually a reasonably good way of looking at major damage on a warship
But obviously also taken from other vessels that have experienced other forms of damage
Because of course Belfast, when she went into her refit
Had a lot of structural and underwater damage
Not a tremendous amount of above water damage
So with that established
The first thing you have to work out when you have a damaged warship
Is what level of damage has this ship actually taken
Because it could be anything from, you know
We're a modernized or fully modern battleship
And let's say in WWII we've been hit by a 550 pound bomb
And a couple of strafing runs from an annoying aircraft or two
That'll have done superficial damage to the upper works
But a 550 pound semi-armored piercing bomb
Ain't going to trouble the deck armor of any decent battleship in the WWII era
Similarly in WWI
You may have been attacked by a particularly annoying airship or float plane
Which again might have done a few strafing runs
Dropped a handful of very lightweight bombs
And that's kind of the best case scenario
Unless you're talking about just splinter damage from near misses
Obviously as things develop
You could have been hit by heavier bombs
That may have caused more damage above the armor deck
You may even have been hit by bombs or shells
That have penetrated your armor deck and exploded further down
And while we're on the subject of shells
You may also have shells that have impacted on your armored sections
And exploded but the armor has successfully resisted
Whether that be turret armor, belt armor or whatever
You may have shells that have hit outside the armor protection
Or have penetrated the less well-protected portions of the armor protection
If you're a distributed armor ship
Mostly in WWI
And that may have induced flooding and instability
But may not be a significant threat to the overall well-being of the ship
But you might also have had shells or bombs
That have penetrated the most heavily armored sections of your ship
Through the belt, into the citadel, into the turrets, etc.
And that could be considerably worse
Then you have to also consider
How many shells or bombs or gun rounds, etc.
Have you been hit by
Because, you know, one shell that penetrates the belt armor
And blows up in a boiler room
And has knocked out several boilers
I mean that's bad
But that's not actually as bad
As say being hit by 15 bombs and a torpedo or two
Because you've got to remember torpedoes do underwater damage
And even if none of those have penetrated the citadel
The amount of damage that would have been done to the ship
Let's say a torpedoes hit the stern
And another torpedoes hit the bow
It may actually be considerably worse
You think for example of USS Boise
Hit in the magazines
There's a magazine fire
That's pretty bad
That's a citadel penetration
But when you look at something like Minneapolis
With her entire bow blown off
Which one is easier to repair
Well actually Boise is going to be slightly easier
To put back together again than Minneapolis
But all of this effectively triage
Is the first stage in repairing a ship
Because you've got to work out
What do we actually have to repair first
Then you have to figure out
How far is this ship from home
This might be a rather critical decision
If a ship is very heavily damaged
And it is very far from home
It may not actually be worth it
Or even possible
To get her back to a repair facility
And therefore a ship in that situation
Might end up being scuttled
Or just put into a relatively austere port
For use as a spare parts depot
Whereas a ship that takes
Exactly the same amount of damage
Much closer to home
Might actually be brought in for repairs
And then there are further levels of this
Because of course if you are
Let's say a British vessel
And you might be on the other side of the planet
But there will be some facilities
In some way shape or form
Available to you from the British Empire
Whether that be Singapore
Hong Kong
Cockatoo Island in Sydney
In Australia
Gibraltar
Malta
Bermuda etc
Now some of these facilities
Might actually be fairly substantial
But it's very rare
If not almost unheard of
The overseas facilities for any nation
Are going to be
At least in the World War I
World War II period
Quite as comprehensive
As the biggest and best
Home port facilities
Now of course if you are
A mildly damaged ship
Then those facilities overseas
Might actually be capable of repairing you
But if you're a very heavily damaged vessel
You might need to put into
One of those facilities first
For some patching up work
Before staging out for home
And it may even be a case
That you have to stage
Through multiple facilities
So to stop the ship from sinking
In a few days
You might need to put into
A relatively austere port
Which is still better than
Repairs at sea
Where you can
At least get the ship
Vaguely watertight
That might then sustain you
Long enough to get
A few hundred or a few thousand miles
Further to a better port
Which might be able to make
Somewhat more substantial repairs
But not rebuilding
Entire sections of the ship
Which then might allow you
To stage home to a major port
If your damage is that bad
And of course
You don't necessarily have to rely
Purely on pre-established
Physical harbors and bays
And so forth
With established settlements
That might have been around
For decades or centuries
Although that is preferable
Because well
In the operational area you're in
Those facilities may not actually exist
But again
In certain time periods
Particularly World War II
It is possible that your navy
Might have brought facilities
Closer to the front line
And you might have to use those
The US Navy in World War II
In the Pacific
Being a good example of this
With multiple large floating dry docks
Which they brought out
Into the middle of the Pacific
Which is rather famously
Sparsely inhabited
And also sparsely islanded
And those dry dock facilities
Allowed badly damaged vessels
To come in and get patched up
Enough so they could survive
The rest of the crossing
Back to the continental United States
And could also do a fair amount of repairs
For lesser damaged vessels
So this is another factor
The distance and the facilities
Between where the damage has occurred
And where the ultimate destination
Of the ship might be
And then the last consideration
Again this is before the ship
Has actually even reached
Any kind of port
Where repairs can begin in earnest
Is has the damage control efforts
That have been undertaken
To mitigate the initial situation
In and of themselves
Caused further damage
Because you might have
Welded doors shut
Or hatches shut
To stop the spread of water
You might have ended up
With compartments flooded
By water percolating down
From firefighting efforts
That in and of themselves
Were not affected by flood or fire
From the initial damage
Likewise water damage
To components
Chemical damage to components
Areas where fires
May have been allowed to spread
In preference to them
Spreading to other areas
So for example if you have a fire
On the starboard side of your ship
And you therefore might
Angle your ship in such a way
Assuming that you have control of it
That the wind is blowing
From port to starboard
Now that blows the flames
Further out and away from the vessel
Which is preferable
But that might mean that some
Of the starboard compartments
That weren't initially on fire
Are essentially being sacrificed
And set on fire
So just the initial damage report
Of bomb entered here
Shell entered here
Torpedo hit here
And did X
That in and of itself
May not reflect the full extent
Of what actually is going to need
Repairing in the end
So now you know the full extent
Of the damage that the ship has incurred
And how far away it is from a port
That may be able to repair it
You can now start to determine
What repairs can be done
In which situations
Because ideally you want
The repairs done as soon as possible
Because apart from anything
That helps improve
The ship's survival chances
As it progresses to the next stage of repairs
Now we have mentioned
A few elements of this before
But we'll go over them
In a bit more detail now
The first sets of repairs
That could be done to a damaged warship
Are the repairs done by the crew at sea
So let's assume that the flooding
The fires etc etc
Are under control
The ship is no longer
In a combat situation
The crew may be able to conduct
Certain amounts of repairs on hand
They will have some spare parts
Assuming it hasn't been destroyed
They will have a machine shop
And so some elements of this damage
Can be fixed immediately
Now that may just be a case of
Cutting away what's now useless dead weight
And just ditching it over the side
It may also be plating over holes
It may be repairing damaged weapons
And sensor systems
So that the ship can fight its way home
Because that may be necessary
You might be shoring up bulkheads
To withstand the stress of proceeding
At a relative degree of speed at sea
Towards wherever it is you're going
You may even have jury rigged
Entire new portions of the ship
Again referencing USS Minneapolis
And some of the other ships
At the Battle of Tassel Faronga
And other related actions
Large amounts of coconut logs
Are not a standard structural material
For US vessels
However it was considered
Considerably better than
Just making do with what they had on hand
To pull in to the nearest island
Where they could get hold of such materials
And shore up the bulkheads
And in some cases depending on the ship
Even construct temporary structures
External to what's left of the vessel
In order to facilitate
Their continued journey home
And even very minor repairs
Can have a considerable impact
On long term repair issues
Once the ship gets home
Because you might think
Well there's some machine gun
And cannon round holes
And some splinter holes
But compared to the fact
There's a 20 foot by 10 foot hole
In the side
Maybe this isn't necessarily
Something we should really bother with
But if you've isolated
The area of the ship
That's being flooded by
The soaking grate hole in the side
Actually patching up
Those small holes elsewhere in the ship
Can save a huge amount of time later on
Because spray, storm winds, the rain etc
If all of that starts to get in
And infiltrate down into the ship
Through the small holes
Or one
That can actually collect
In fairly alarming quantities
Especially high up in the ship
Which can badly affect
The ship's stability
But two
That can also further damage systems
That were not originally damaged
So you know
Water getting into the electrics
Water getting into compartments
Which hold supplies
And this kind of thing
That is going to make
Both keeping the ship afloat
On its way home
And the subsequent repair efforts
Longer and more difficult
So even small repairs
Need to be done
As soon as humanly possible
You might also have
Scavenging operations going on
Whether that be
Again mostly for guns and sensors
But it could also be for
Generators, drive motors
Hydraulic systems etc etc
Not only for getting
Some of those systems operational
In the event that the enemy
Who damaged you
Tries to come in and finish you off
But also because
Again in the interest of
Getting back out into combat
As soon as possible
Let's say your ship has
Two primary fire control directors
Up top
So you know
Your range finding devices
Now those might be radar
They might be optical
They might be a combination
But if both of them
Have been damaged in the combat
And they're both non-operational
But you don't have enough spare parts
To repair both of them
And maybe you don't even necessarily
Have all the spare parts
To repair even one of them
If you can cannibalize
One plus your spares
Plus your machine shop output
To make the other fully operational
Well one you now have
A fully operational range finding
And director system
Which is good
And two
When you pull into port
You can tell the officials
Well we need one replacement system
Rather than two
And this is good
So that's a broad overview
Of the repairs you could do at sea
Then you might reach
What you might term an austere port
I.e. it's a harbor
It's relatively safe
At least from the elements
But maybe there's not a huge amount
Of material available on hand
To make repairs
So for an austere port
You wouldn't necessarily expect
To have replacement
4.5 inch, 5 inch guns
Or 40 mm Bofors
Or radar systems etc
But you might expect to find
At least some metal sheeting
Timbers, tarpaulins
And this kind of thing
In substantially greater quantities
Than you had when you were out at sea
You might also find food, water
Basic machine parts etc
Even things like grease and fuel
And all of this can be used
To further supplement
The repairs you've done at sea
And to patch up things
That perhaps you couldn't do at sea
So assuming we're talking about a ship
As we said earlier
With a massive great hole in its side
You may have been able to isolate
The flooded areas
And shore up the bulkheads around it
But nobody is going to be
Lowering crew over the side
In rough seas
With several tons of steel plate
And trying to get them to spot weld
Things in place
Some efforts may have been made
In the form of a canvas barrier
Or something
But that's not a long term solution
But once you get to an austere port
In relatively calm waters
You may be able to plate over
Some if not all of the biggest holes
In the side of the vessel
Because you're no longer moving
Hopefully the waves aren't quite so large
And you might have access to
The steel plate in the size
That you need
And or maybe even a crane
To help you lift it
Or a crane on a boat
So the austere ports
Are essentially there
Just to make sure that your ship
Isn't going to sink
Through progressive damage
Further on
You might then move forward
To other ports as we said
And that will essentially be
Repeating this procedure
But in better and better quality
Until
Because of course we are assuming
The ship has major damage
You get back home
Or you get to a port
That maybe isn't
In your home nation
But is big enough
To make the repairs
In either case
You and
Well the navy realistically
Has a big decision to make
If of course they can
Actually make such a decision
Because it may just be a case of
Well this is the only available berth
You're going in there
At least for now
But let's assume that
There is multiple areas
Within this port
That can accept your vessel
How has your vessel
Suffered its major damage
If you have lots of bomb and shell hits
Well above the waterline for example
So your upper works
Have been really badly shot up
Maybe turrets knocked out
Etc etc
Now this is obviously quite bad
But it's all within the capabilities
Of being repaired
At a pierside, quayside, wharfside
Whatever your particular dock
Happens to be set up as
I.e. whilst the ship is still afloat
So if your underwater integrity
Is still fine
And there's not any particular damage
Near the waterline
You may just pull the ship up
Next to whatever it is
Wharf, pier, quay as I said
And then the heavy duty cranes
Which most dockyards will be there
For fitting out
Will be more than capable of lifting
Anything that needs to be removed
And the repairs can commence there
Conversely
If there are serious stability issues
With the ship
Because of water on board
Whether that's from firefighting
Flooding or both
If there's serious damage
Below the waterline
Mine strikes, torpedo strikes
Shell strikes etc
Or at the waterline
That kind of thing
Basically anywhere
Where the damage would
A. Potentially encourage
Further ingress of water
Whilst the ship remains afloat
And B. Be very difficult to access
Because it's either in or near the water
Then the ship would need to go
Into a dry dock
And once the ship is in the dry dock
Then obviously it would be positioned
The water would be drained
The water would then hopefully
Drain out most of the ship
And repairs can then commence
So congratulations
Your ship has made it home
To a major port
Where it can undertake full repairs
Now again of course
We are assuming your ship
Has taken major damage
And we're going to include
Major underwater damage
To get the full experience
So we're assuming in this case
That the ship has gone into the dry dock
Now how do you repair the ship
Well the first thing to do
Above anything
Is to make safe
Any structurally compromised sections
Because the last thing you want
Is the ship falling over in the dry dock
Or breaking apart in the dry dock
Because obviously now the ship
Without the water surrounding it
Is under even more stress
So any structurally compromised area
Of the vessel
Will need to be patched up
Shored up
Plated over
There will have to be some kind of
At least temporary
Maybe possibly ideally long term
But probably temporary repair
To make sure that the vessel stays intact
And when the ship is pulled into the dry dock
If the damage is bad enough
This may actually be done
With the dry dock still flooded
Or possibly partially flooded
Or partially drained
Depending on how you want to look at it
In order to retain that support
From the water
Whilst this initial
Structural compromised
Section of the ship
Is made good
Of course if the ship
Is in that bad a way
It may not actually have made it back
But we're assuming that
It's made it back
But perhaps there's something
That is on the verge of going
Because this is another thing
You've got to bear in mind
A ship may be able to remain afloat
And make it home
There may be something
That's sufficiently compromised
Within the vessel
That there's a decent chance
Of the ship breaking up at any moment
And indeed in a few cases
This did actually happen
Where a ship survived
Its initial encounter
With the enemy
But would break up
And sink on the way back
HMAS Sydney for example
In the aftermath of its battle
With Cormorant
USS O'Brien or O'Brien
In the aftermath of its torpedoing
At the same instant
That hit North Carolina
And killed Wasp
And of course the stresses
On that section of the ship
Are continuous
So just because the ship
Has survived this far
Doesn't necessarily mean
It's going to quite happily
Stay intact
Without any further intervention
Going forward
But once you've stabilized the ship
If it's necessary
From a structural perspective
The next thing to do ironically
Especially in World War II
Not so much in World War I
But maybe sometimes
Is to actually check for
Refit or upgrade potential
For the ship
Because that will dictate
To a certain extent
Any actions that are going further on
Now that may be upgrades
In the forms of removing
Some systems to install others
Say removing secondary batteries
To install dual purpose batteries
Removing existing fire control
And radar systems
To install more modern ones
Or it may just be
Flat out installing new stuff
So you don't have many
Light anti-aircraft guns
Now you have lots of
20mm Oerlikons
You don't have radar
Now you're going to get it
And in some cases
That may involve other aspects
Of the ship being changed
Such as for HMS Belfast
She had vultures placed
But then as well as additional armor
But the armor was placed
Outside the vultures
So you have to check what
If anything is wanting to be done
To upgrade the vessel
Not just return it
To its original state
Having done that check
Which hopefully will have been run
In parallel with the previous incident
Then you need to start
Removing damaged materials
So you might have
Shattered hull plating
Bent up decking
Broken components
Anything up to and including
Burned out turrets
That kind of thing
You've now got to
Get rid of all of that
So some of it
If a turret's been hit
And burnt out
Then you might just
Lift the turret off
You might dismantle it
If you can
But in either case
It has to go
For hull plating
This may be slightly different
Depending on whether the ship's
Been welded or riveted
But broken and twisted
Hull plating will need to be
Taken out
Whilst that major damaged material
Is being removed
You would then recover
Also smaller debris
Shattered bits and pieces
Now a lot of that
May have been cleaned up
By the crew on the way back
But there may be
Random bits
Shrapnel embedded
In the side of the ship
Fragments of the bombs
Et cetera
Or shells
All of that kind of thing
Will need to be
Recovered and removed
Because you don't need
That around anymore
Not that you ever did
And removing this amount of material
Which of course may even include
Things like
Damaged or destroyed boilers
Or other parts of the
Machinery deep in the ship
This is going to change
The weight of the vessel
And its balance
Not just in terms of
Its balance in the dry dock itself
Which could be a problem
But also where the stresses
Are located on the vessel
So you may have already
Made safe the
Compromised areas of the hull
But you're now
As an ongoing process
During the removal of
The damaged material
Going to have to be
Continuously stabilizing the hull
To make sure that
Again it doesn't roll over
Or collapse in the dry dock
And also that
If there were stress points
Which you have made safe
If those stress points
May now have moved
Because you've taken bits off
You need to make sure that
These other areas are not
Badly affected
So you're now taking off
All the stuff that's
Fully broken
Now to commence repairs
You have to cut back further
To points where you can
Actually join new material on
And this can be everything
From hull plating
And hull girders
All the way down
To wiring
Because again
Let's take an example
Very easy of wiring
Let's say you have
Something like
An electrical distribution bus
A nice big chunky thing
That's been hit by fragments
Shorted out by water
Burned by fire
Whatever
So it's dead
So you've cut it out
And removed it
And a new one's going to come in
Great fantastic
However of course
This thing was wired up
To lots of stuff
In the interest
Of efficiency
And just getting the thing out
You will have cut off
The wiring that
Both is coming in
And going out of it
Pretty close to it
Now you could try
And wire its replacement
Into this existing wire
But you've now got a wire run
Or multiple wire runs
That are cut part way along
Now splicing those together
Fine it could be done
But it's not necessarily
Best practice
So at that point
You would want to trace the wire
To its next junction
Wherever that happens to be
And remove that whole section of wire
Now that section of wire
Is too short
For this particular use
But maybe that can go on
To be used in other areas
Where it doesn't need
To be quite as long
It can be used in other ships
Whatever
But you would ideally want
To replace that section of wire
With a whole new section
Even if 90% of that bit of wire
Is actually undamaged
Of course wartime exegesis
You may need to splice it together
But it's not brilliant
More importantly
When it comes to structural elements
If say you have
A 20 foot long steel girder
And at one end of it
It's been blasted and twisted and warped
But you cut off
Say 10 foot of it
And the remaining 10 foot
Is actually good steel
Again you could try and weld
Another 10 foot section of girder
Onto it
But you are creating a weak point
Along that girder
It's better at that point
To remove the entire girder
And replace it with a whole new
Entire girder
And the same thing with hole plating
You've got a 40 foot by 40 foot
Section of hole plating
It's probably slightly large
But nonetheless
And there's a 10 foot by 10 foot hole
In one end
You could patch and plate it over
But again in an ideal world
You would just want to replace
The entire plate
So now you've taken the ship back
As far as you're likely to do
In this repair job
Now you actually start making
The repairs
So smaller damage
Machine gun rounds
Cannon rounds
Splinters
That kind of thing
You know if you've got
Again let's say on the superstructure
Maybe there's a 15 foot by 10 foot
Section of plate
And the only damage is
You know a 2 inch by 1 inch
Splinter hole through it
There's no point taking off
That entire thing
It's not armor plate
It's not structural
You can just put weld or rivet
A little spot plate over it
And job's done
You know the thing is sealed
It's got as much protection
As it ever did
Plate over the smaller damage
Meanwhile further down in the ship
The structural level repairs
Will commence
So that'll be replacing of girders
As we just mentioned
Replacing of whole sections of plating
Further up if your turret was dead
Then you might be putting in
An entire new turret system
Or if a gun got broken into
Obviously you would have to
Take the roof off of the turret
Remove the entire gun
Now a new gun is going back in
Obviously at this point
If you were going to
Modernize and update the superstructure
All of that would be being done
But that's not really repair
That's just part of the upgrade
That has been allowed by the fact
The ship's back in dry dock
And through all of this
You are going to be rechecking the hull
Continuously to look for warping
Changes of balance etc. etc.
Now in some very very specific cases
You will also
During this early process
Have some rather complicated
Engineering going on
Even above and beyond
Normal ship repairs
So with HMS Belfast for example
Her keel was very badly bent
By the mine explosion
And when she was brought in
The entire ship
Obviously above where the mine had gone up
Had bent upwards
And in order to facilitate
The ship re-entering service
She was actually at first
Dry docked in a way
With the dry dock block
Such that supported
Her current hull shape
Which was of course warped
But then once they had done
The initial bits
Where we talk about
Removing the damaged material
And so forth
And they started in on
Some of the initial repairs
She was then allowed to settle
So that meant cutting back
The dry dock blocks
Using her original plans
So that the dry dock blocks
Reflected that the ship's hull
As it should be
And that meant of course
That the area of the ship
That had buckled up
Was now unsupported
And the sheer amount of weight involved
Several thousand tons
Began to bend the hull
Back towards its original position
And obviously bend the keel as well
And that had to be checked every day
For weeks on end
As the ship gradually settled
Back into what its original
Hull shape should have been
And then further repair work
Could go on
Because for example
If you are going to be
Fitting a bulge
As they did on Belfast
Or a new armour plate
Replacing armour plate etc
Even hull plating
You're not going to want to do that
When the hull is warped out of shape
You're going to have to wait
Until the hull is actually
Back into the correct shape
Before you continue with the repairs
So now your major
Structural repairs are done
And your really minor damage
Has been patched up
Now you can start
Replacing components
So if you had to replace
Boilers, turbines
That kind of thing
That would all have been done
Under the vague heading of
Larger structural repairs
But now things like generators
The power distribution bus
We mentioned earlier
Boats, aircraft, radar, range finders
All this individual elements
Of the vessel that might have
Had to have been removed
Everything down to you
Switches and relays etc
All of this can now be replaced
And that's not to say that
You couldn't have replaced
Those things earlier
But simply that
Once the ship has been
Fully stripped down
To its minimal state
As we mentioned earlier
That is the most ideal time
To start bringing in
All the big heavy stuff
Because there's the absolute
Minimum amount of stuff in the way
Whereas if you have
Various smaller bits and pieces
That have now been reinstalled
They and potentially also the people
Who are doing the installation
May get in the way
Of putting the bigger stuff in
Depending on the navy
And depending on the time period
The one of the last parts
Might also now be the replacement
Or reinstallation
Of the really big stuff
So if you had a damaged conning tower
Or a main gun turret
That may come in at the end
It's also one of the things
That's lost in the fitting out stages
Of a ship
It may as we indicated earlier
Have been done much earlier
In the process
So if you're a ship with
Four or five main battery turrets
And one of them has been
Badly shot up and needs replacing
Dropping that in and out
May be done partway
During the repair cycle
But if you've got
Maybe three main gun turrets
Or you've had
Multiple gun turrets burnt out
Basically if there's a substantial portion
Of your main battery firepower
That has been destroyed
Or badly damaged
Then putting all of that back in
May be a latter stage process
But again
Depends on the amount of damage
Depends on the navy
Depends on the time period even
Because if you're in World War I
And we're talking about a cruiser
A lot of those guns
Are going to be single guns
Usually deck mounts
There's not that many
Turreted guns as a whole
In cruisers of World War I
And fewer still are twins
At which point
If a 6-inch open gun mount
Or something with a gun shield
Has been knocked out
Repairing that
And or replacing it
Will happen pretty much
Whenever it can
Whereas if we fast forward
To World War II
And you're talking about
A triple 8-inch turret
Yeah, that takes a bit longer
To make a new one anyway
And it's a much more involved operation
To put it back in
Nonetheless
All your various bits and pieces
Have been put back in
Your hull's been straightened up
The plating's gone back in
The girder's gone back in
You've rebuilt
All the internal components
Passageways and so forth
Now you get to integrate
All the new bits
You might have installed
Because of course
Now all of the ship is there
So your new radar
Can be hooked up to check
Does this work
And is it feeding the right data
To the turrets
Is it feeding the right data
To the anti-fire control table
The Mark I range keeper
Or whatever system
You're using for fire control
If you've, say, installed RPC
Remote power training
Or remote power control
To some of your secondary
Or main battery
Is that working correctly
If we, say, turn the turret
30 degrees to starboard
Is it going 30 degrees to starboard
Is it going 29 degrees to starboard
Is it elevating properly
Et cetera, et cetera
Once you think
Everything's approximately working
Then given that we've been talking about
A fairly major repair job
It's now time to re-crew the vessel
Now that may be an entirely new crew
If your vessel's been in the dry dock
For a year, two years or so
Something like, say, USS West Virginia
Near enough is going to get a brand new crew
Because any experienced crew
Who were on the ship
Will have been redistributed
To other ships long ago
But you may also get a case
West Virginia, more particularly
With something like Belfast
Where a core element of the crew
May have been retained
Because they have expertise
On what the ship was like
And how the system
Should go back together again
And then the re-crewing
May take place around them
As a cadre of experienced people
But nonetheless
If you're talking about a ship
That's gone in for very major repairs
Chances are that the crew
Is going to be mostly, if not entirely
New to the ship
And of course you have
All these new components
And repaired components
Which means that when the ship
Comes back out of the dry dock
You are going to have to do
A shakedown voyage
It may not be a particularly long one
If you're in the middle of war
But you are going to have to do one
Because that helps the crew
Get familiar with the ship
It means that anything
That you've installed
That may or may not break
Once the ship's actually
Fully up and running and underway
It will hopefully break at that point
And you can go
OK, well this is out of alignment actually
This got knocked out of alignment
And needs recalibrating
This has stopped working
So actually we need to pop back in
And do a few adjustments
And repairs
Which, you know, depending again
On wartime ecstasies
You may be going straight back
Into dry dock if it's fairly major
If it's relatively minor
And the crew on board
Know how to repair the things
They may actually just repair them
You know, as the voyage goes on
But in either case
You will end up coming back
Into port and going
OK, here's the stuff that broke
Here's the stuff that either needs fixing
Or that we have fixed
And now, in theory at least
The ship is ready to re-enter service
At which point
The ship will be
Either sent back out with its new mission
Or if it has been in dry dock
So long as it was actually decommissioned
It will have to be recommissioned
And then sent back out
Into the Wild Blue Yonder
So that is a very short
Comparatively speaking
Overview
And a very high level overview
Of how you would go about repairing
A damaged warship
Obviously with various break points
Where we've noted
If the ship was suffering
Medium or light damage
Only part of this may apply
But we've followed
The general route of a ship
That has suffered
Some fairly hefty damage
And then it goes into dry dock
To get that repair done
For obvious reasons
Given that these jobs
Take months or years
And that each ship
Is obviously different
Takes different damage
Has different systems to damage
In the first place
It's difficult to go into
Very, very specific detail
About any very specific vessel
Or very specific procedure
But hopefully this has given you
A good idea of
Roughly what you would be expected to do
Taking a ship through its full life cycle
If you want to know about
Specific ship repairs
Such as say the procedure
To take HMS Belfast
From a mined cruiser
That was very nearly written off
Or perhaps even a continuation
Of the Pearl Harbor recovery series
Because of course that series
We looked at how the vessels were salvaged
But each of those vessels
Kind of left the narrative
At the point they were sent off
To the continental United States
For actual refit and repair
Maybe you want to know about
How West Virginia was taken
From essentially a shattered hulk
To being a fully operational capital ship
Those specific ship instances
We can look at in a video
Some point in the future
And if you'd like to do that
Then obviously let me know
In the comments below
And I can add it to the
Long, long, long, long list of things
That we have to look at
Nonetheless
Thank you very much for listening everyone
And see you again in another video
That's it for this video
Thanks for watching
If you have a comment or suggestion
For a ship to review
Let us know in the comments below
Don't forget to comment on the pinned post
For dry dock questions
