Hey folks, how you guys doing?
Hope you're all having a great day today.
Like many of you out there,
I have a hard time throwing away scrap wood,
small little parts here and there,
especially if it's a nice hardwood,
because, well, you know, you can use it for something, right?
And my excuse has always been, I could use that for a pen.
I could put that on a lathe and turn a pen with it, right?
Pen blanks.
Yeah, I've been using that excuse for years
and barely turn any pens anymore.
So one way to use up some of this scrap wood
and try out a new technique
was to make some drawer pulls on the Pantorouter.
And I thought the process was a little bit interesting,
so that's what I'm gonna show you today.
So this is a one solid piece drawer pull.
You have an integral tenon on this side, so a dowel,
and then whatever decorative shape you want on this side.
And in this case, I just used a dovetail bit to create,
well, something that looks like this.
If you just drill a hole into a drawer front or whatever,
slide it all the way through,
and that's the look you're gonna get.
But you can use a lot of different router bits,
OG bits, maybe like a tongue and groove bit
to create almost like a nail head.
Yeah, I guess a nail head would be the best way to say it.
So your limit is,
you're only limited by the router bits that you have.
Process is really simple,
and that's what I'm gonna show you today.
This is just a chunk of two by four
that I very crudely drilled a bunch of quarter inch holes in
and one half inch hole,
because I like to have this little block
sitting on top of this table as I'm working,
the PantoRouter table as I'm working,
just for quick access.
I don't have to keep opening the drawer back and forth.
But as you can see, I made a bunch of these
quarter inch drawer pulls already,
and we're gonna use three different router bits for this.
This is a half inch spiral upcut router bit.
All of these are astro-coated by bits and bits.
So this darker section, this is an astro-coating,
and it reduces friction, reduces heat buildup,
prolongs the life of the bit.
This is a half inch spiral upcut.
We'll use this.
We'll also use a quarter inch spiral upcut.
And for this particular shape that I've already shown you,
we're using this eight degree dovetail bit.
This is the type of scrap wood that I'm talking about.
You know, small boards like this.
I took these and ripped them down
to about one inch by one inch on the bandsaw.
As you can see, there's already a tenon on one of them
from just playing around.
But this type of scrap will allow a lot of pieces
to be made at once.
Simply make a dowel on either end,
take it over to the table saw on the crosscut sled,
cut these off, and then create two more dowels
on either end, take them to the table saw, cut them off.
So you can batch out a bunch of these very fast.
What makes this process so fast and so repeatable
is the use of these templates.
Now this template is perfectly centered.
Well, I say perfectly centered.
As centered as I can get it left and right
on the template holder.
Now there is holes in here that,
with the rest of the templates,
you can line up the center of the template
into one of these one, two, or three centered holes.
But obviously we need a screw here
to hold the template to the template holder.
So instead of using this to center the template,
there's a little notch cut,
which is difficult to show up on camera,
but there's a little notch on the top center of the template
and you line that up with the line
that's been scratched on the center of the template holder.
With the guide bearing in the center of the template,
the mortise or the hole will be cut with this dowel template
and with the guide bearing riding around the perimeter,
the tenon or the dowel will be cut.
We're making the dowels first.
So we'll start with the half inch spiral upcut router bit.
It's worth noting that you need to cut the mortise
before the tenon.
The reason being is the mortise is just whatever size
the router bit is.
So it's gonna be a fixed size
and then the tenon can be dialed into the fit that you want.
So in this case, I took a piece of something really hard.
So it's not going to deform at all
from various different attempts to size something.
So I've got a quarter inch hole
and a three eighths of an inch hole.
Both of these were cut with the router bits
that I'll be using.
I may or may not use the three eighths,
but I went ahead and made one simple
because it's easy to do it
while I'm already set up to do that.
And now that I have a hole to gauge the dowel,
I can dial in the size of the dowel as I'm cutting it.
With a piece clamped to the table where I want it,
I can slide the carriage forward
so that the router bit touches the material
and then set my backstop.
Now from here on out,
I know with the router bit, with the router stopped,
the exact location of the material.
I can just slide it forward until it touches the router bit.
So that's the backstop.
Now, how far forward do we want to go?
Well, I'm just gonna shoot for about a one inch long dowel
and that should accommodate all of the situations
where I would use a drawer pull one inch in length.
It'll give me a little bit extra that I can trim off
for say like a three quarter inch material.
And it'll also give me a little bit sticking out
if I ever wanna wedge these dowels in place for drawer pulls.
So now I know that my dowel is going to be this distance,
which according to the scale is exactly one inch.
Now the only thing left to do is dial in the exact,
well, you kind of can't see it,
the exact position of the guide bearing on this template.
I'll go ahead and dial in the position of this guide bearing
for the tenon or for the dowel without dust collection.
So you can see what's going on.
So you can see the process.
Then I'm gonna put dust collection on
because I don't want to suffer.
But basically we're gonna start with this guide bearing
close to the template holder and then move it further away,
which will reduce the thickness
or reduce the size of the dowel.
And we'll periodically test it after every cut
up against this little guide block here.
And notice that I'm going counterclockwise
around this template.
And that's so that we're making a climb cut
all the way around the piece here.
And that'll give a more accurate size
when it's all said and done.
You're not gonna have the bit deflect into the material,
which I don't think will happen with a half inch bit,
but a quarter inch bit it can.
So with our quarter inch hole, nope, it's too big.
It will not fit in the hole.
So now we can take our template, our guide bearing here
and pull it a little bit away from the template holder.
And therefore seeing a smaller diameter
that we're gonna trace,
the perimeter of this template is on an angle,
sloped a little bit.
All right, that's a good fit.
It's actually a little bit loose.
I went too far.
But the way I see this,
well, maybe that's too loose.
I was gonna say that the PVA glue
will expand the wood a little bit
as it's being seated home or as the dowel is being seated,
but I think that's just a little bit too much.
So let me go ahead and mark on this one
to cut this one off and not use this one,
but I'll go ahead and flip this piece around
so I get a fresh block to start with.
And here's where that backstop comes into play.
So with the bit not running,
I can slide this up against the bit,
clamp this down, clamp this down,
bring this back up here,
and we're gonna climb just a little bit up the template.
And we'll try again.
All right, I'm gonna call that dialed in.
So with that being set,
I can go ahead and put the dust collection on.
So I won't spray myself with all this
and get all of these knocked out real fast.
So the eight boards that we had earlier,
two per board, one on either side,
that's 16 minus the original one that I put pencil on
to tell me I need to throw that one away.
But now I can separate all of these
at the crosscut sled on the table saw
and repeat the process
until I don't have any more usable material left
just to see how many I can get.
I don't need this many.
I actually don't need any.
I'm just kind of experimenting right now and having fun.
All right, just that fast, I got distracted.
The earth spun around one more time.
It is a new day.
I got this many cut.
All of these in this pile
are about an inch and a quarter long.
I think something like that.
Just rough cut with the table saw.
And these are all seven eighths of an inch long.
So the next step is to cut a setup block
or a clamping block on the panto router
so I can clamp the dowel
in a repeatable position every single time
and then face off all of these shorter ones
to a length of about three quarters of an inch for these.
And I don't know on these yet.
I'm gonna have to figure out a length for these,
maybe one and one eighth.
Anyway, I just need consistency with all of these
to make sure that they are all perfectly
the exact same length.
And also this face over here,
the front face of the pole
needs to be the exact same distance
from the start of the dowel over here.
So these clamps are great.
I really like them.
They're easy to use.
The only downside of these is sometimes
you can shift the material one way or the other
as you're clamping these down
because the rotational direction here
will sometimes shift the pad.
So I want this to be as foolproof as possible.
I want this setup to be,
just to not move one bit whatsoever.
So I do have the fence as a reference face,
but I'm gonna take that a step further
and put one of these front stops on the table.
And I'm gonna put one on this side of the fence.
So it just acts as another locking point
to stop the fence from moving.
So I'm not gonna be shifting that way any.
This is going to be a consistent size every single time.
Let me go ahead and make a mark on this side
to go up against the fence.
And then I can use this other,
let's see if I can put my pencil in my pocket,
this other front stop over here on top of the table.
Right here.
Maybe.
It's gonna be in the way of the clamp.
Let's go right here.
And now this should eliminate any type of twist
or shifting of the stop block this way.
I'll use one clamp over here to pin it in place.
And then this clamp will be a toggle
to clamp down on the dowel every single time.
But before I can do that,
I need to drill a hole in here with the router bit.
The clamp in back immobilizes this block.
The hole drilled in the front
is to allow for repeat alignment of all of the knobs.
And the slot cut at the bandsaw
allows for compression of the block on top of the dowel.
So it's like a little toggle clamp.
So I'm gonna go ahead and face off all these short ones
at three quarters of an inch in length.
All right, so I ended up with three different lengths
and it'll just give me some wiggle room to experiment with.
So for the first one, these shorter ones,
that's what I'm going to use
to make these small little dovetails.
Now, there is something to note about these
and I don't know if it's gonna show up.
Yeah, I think you can see it.
See the shoulder of the dovetail is pronounced there.
You can see the shadow line right there.
And if I spin it around,
that shadow line somewhat disappears.
There's still, I can still feel a tiny ridge.
So it's not completely off-center.
Well, it is off-center,
but it's not catastrophic, I guess you could say.
So there's a little bit of a shoulder all the way around.
So the thing is something shifted here,
whether it's this or whether I'm clamping
and twisting this a little bit or something's moving.
So I'm not getting 100% perfect, consistent results.
So there's a couple of things I can do.
Number one, I can climb the guide bearing
a little bit higher on the template.
So it produces a slightly larger dovetail, which is fine.
No big deal, I can do that.
But one of the things that's just the easiest way
to make this consistent,
because at the end of the day,
you're not gonna notice a 64th
or a 32nd of an inch right there, however much that is.
You're not gonna notice
that being off on the drawer a little bit.
But you do want consistency
if you're lining up multiples together.
So the way I'm going to gain consistency
is if I put this in a drawer,
I'm gonna wanna have all of the grain
either horizontal or vertical.
All the grain's gonna have to match up, right?
So if that's the case,
then I can make sure that all of these are mounted
in such a way that the grain
is the same orientation before I cut.
And then whatever error or whatever offset
that I have in my setup here
that I don't really need to track down,
whatever error that is, it'll be consistent
and it won't ever be seen or noticed
because it's all gonna be,
well, it's gonna be in the drawer.
All of the poles cut.
And I tried a few different router bits.
I didn't record any of the various different router bits,
just the dovetail bit,
because, well, it's the exact same process
and I'm more or less kind of experimenting,
trying to figure out what I do like, what I don't like,
streamline the process, what can I learn from it?
And there's a few things that I did learn from it.
Not all creativity turns out to be nice in the long run.
But anyway, let me bring you in closer
and I'll check out all the results.
All right, what do I like?
What do I don't like?
What would I do again?
Well, this is all an experiment,
so it was fun to just chop stuff up
and not really have a game plan in mind
or an end goal in mind.
The smaller dovetail poles,
I really like for something like a jewelry box or something.
You know, that's gonna be a great size
for small boxes and whatnot,
even if it's like a little finial
on the top of a box, right?
So that's gonna be a nice little pole to keep on hand.
So this was, let me put this back in here,
this was created with this particular dovetail bit, right?
Small dovetail bit, small dovetail pole.
I wanted to have something a little bit larger,
something for something I can see
on a dresser, chest of drawers.
So for that, I made this one,
which is, as you can see, much larger
and it was cut with this larger dovetail bit.
And this is sized appropriately, I think,
for like a dresser, chest of drawers,
something where you're gonna be pulling
a little bit larger of a drawer open,
so you want a little bit larger of a pole.
I like this.
I wanted to expand upon this even further
by cutting some type of profile
on this outer edge right here.
And I've got this, like this recessed roundover bit
that you can plunge into the surface
and get kind of like a compound roundover.
I was going to mess around with it,
but I ultimately decided not to
because I've got quite a few of these
that I really like and might use on an upcoming project.
Didn't want to screw them up
because I was having some issues
with getting everything mounted concentrically
or in the same exact location,
so I didn't want this to be not quite perfectly centered.
So, eh, maybe I'll experiment with that at a later date.
So I like these.
Also, when I was cutting these smaller dovetails,
I took too big of a bite and broke one,
which prompted me to first,
instead of going right to the profile bit,
to first use a two-flute spiral
to reduce the amount of cutting surface area for the profile.
So just a roughing cut,
and I thought, well, that's not bad, actually.
Just, again, very basic, very simple.
So I cut a bunch of these to have on hand, too.
Just a very modern button, right?
I like that.
So while I was already set up,
I did the exact same thing in a much longer version.
So I got some of different lengths, which are nice.
And then I just started to experiment,
and that's where it all went downhill
as far as the way that the stuff looks.
So I've got some of the longer pieces of those double dowels,
whatever you want to call them,
and I thought, let's see if I can't make some small grooves
with a tongue-and-groove bit set, right?
So first off, way too deep on these.
This is way too deep.
I was trying to experiment
with my different guide bushing sizes,
and I didn't really have one that was working,
so I made a quick little block
that I could rotate around the template,
and the cut was just too aggressive.
That just doesn't look good.
So I backed it off quite a bit
and made another little template guide bearing.
For the template.
And this is the result there.
Eh, a little bit better,
but I think spacing can be improved.
Not great, but whatever.
Maybe half of this, right?
So maybe the pole starts right here
instead of way back here,
and it's just a little button from there.
I think that would look good.
I also took one of the regular poles like this,
the cylinders, and I used a chamfer bit
to cut a little groove in it,
and then also slightly chamfer this outside edge,
and I think that looks all right.
I think that looks neat.
But I think that's it.
I stuck with making a lot of these cylinders
and a lot of these larger dovetails.
Got a bunch of these on hand.
But anyway, I thought the process was interesting.
As I said, even with having all these stops in place,
I was getting some shifting here,
and that might be due to just the way
that this is clamped down.
Maybe the slot is a little bit too far down into the hole.
Maybe it needs to be a little bit higher,
so you have more surface area on the bottom side
of the hole to locate the pole before it's clamped down.
I don't know, but I think this was the weakest link
of this entire setup, even with these stops
on either side of the fence and the material.
I think a better solution would be something
that is similar to a bench hook
or similar to a shooting board.
Something that has a piece of plywood
with a cleat down here that pushes
and references up against this edge
before it's clamped down multiple times.
And I think the better clamps,
instead of using these included clamps
with a panel router, I think the better solution
would be to clamp it down in such a way
that it's very similar to these.
You have a screw that goes down into a slot down in here
or a T-nut down in here.
Something that has perfectly vertical clamping pressure
and it's not being skewed one way or another
potentially by this.
So area for improvement mainly is this.
And then also, if we're referencing off of the side
of the table every single time,
then you can locate the stop in place
or the block in place and get it clamped down,
put a bit into the panther router
and center it in that hole to center the template up there.
And you can have a lot of repeatability
and a lot of precision long-term
with various different setups or various different times
you're breaking down the setup
and then installing it once again
to batch out some more of these.
That's it for this video.
I thought the process was interesting
so I wanted to share it with all of you.
It's a great way to get a really customizable drawer pull,
not only based upon the profile router bit that you're using
but also the species of wood that you're using.
So if you need a really good color match
with the project that you're actually making,
you can use offcuts from that project
to create seamless drawer pulls that match.
So it's a really cool concept that you can expand upon
in many, many different ways.
Speaking of expanding upon,
this original design of the panther router
is from Matias Wandel
and he's got a set of plans that you can purchase
to create your own out of wood.
I'll have a link in the description down below
where you can check those out.
But if you're not interested in making your own tools
and you simply just wanna purchase them
and use them to create awesome projects,
well, Mack Sheldon over at pantherrouter.com,
they've expanded upon the plans
to create this full-blown panther router machine
out of metal.
So you've got a lot of options for the machine
if you're interested in one of those.
I'll have links in the description below
to both of those options.
And one final thing is a shout out to Bits and Bits Company.
I'm doing a little bit of advertising work
for Bits and Bits.
It's a small USA-owned, USA-ran business
that creates their own router bits.
That also is a distributor of Whiteside router bits
and they coat all of their bits in an Astra coating
which reduces friction, reduces heat buildup
and under normal conditions will greatly increase
the length of the lifespan of the router bit.
They're also a new Festool dealer.
So if you're interested in Festool products,
doesn't matter where you purchase them from,
Festool sets their prices everywhere.
So it's gonna be the same price
no matter where you purchase.
If you'd like to support a small USA-owned business,
then consider purchasing through bitsandbits.com.
Link is in the description below for that
as well as a coupon code.
I feel like I'm just blabbing on about stuff.
So you guys take care, have a great day.
Oh, one last thing.
If you'd like to stay up to date with all my stuff,
go to my website, jscustomcreations.com slash newsletter
and sign up for my email newsletter
so you don't miss anything that I publish.
You guys take care, have a great day
and I'll talk to you in the next video.