How to Make a Hoplite Shield | Ancient Greek Aspis

Shield of Antiquity
8 followers
16 Video Views·Jul 16, 2025
This is how I made a Hoplite shield known as an Aspis, I hope this can guide you on your way to create your own.
Comments are disabled for this video.
So I cut out a template just to put on the woods and trace round.
The template was 36 inches, that is how big the entire asbestos will be.
I used a pen, two pencils to measure it, the string would be 18 inches because it's half of 36.
I must have accidentally done something wrong so I cut off about two inches to make it perfect.
Here's roughly a diameter and here it is tracing round and cutting out the pieces of wood.
Here we are gluing it.
I used a plane to get most of the nastiness off that a sander couldn't.
Then I went on with a sander and as you can see it's just going
back and forth basically, it's very time consuming.
Here's the sander, that's just to get it fully smooth.
Then I used wood fill to fill it afterwards.
And then for the inside I used an angle grinder with a really tough sanding
end and it really took it off and then sanded the rest.
So this is the inside after we have used the angle grinder and then just sanded it down a bit.
And then I just applied some filler around here just because you don't want to sand it
too close down to the other grain because it will, um, might start to unglue it.
So I'm adding a little bit of shim around here at the spring to fill up how it's going to snap.
But, um, don't go down too far on this one.
These ones are fine, pretty much, you can get it down.
Like that.
Then basically I'm going to wood stain this just to get rid of it's sort of, uh,
colour and just block of brown on one.
And then it's time to put it on the argyle for it.
Um, then it's leather coating and then it's done.
So I thought I would wood stain it but then I decided, uh, because it didn't look that good,
I actually wanted to coat the inside, uh, with leather.
Um, you could just wood stain it if you wanted.
But here we are making the inside.
So this is called the forepacks, it's basically what holds my arm into the sheet.
Uh, it's a sheet of copper, my dad just got this from work.
Um, and I used the, I think they're called tin snips, I'm not entirely sure.
And here we are cutting them out.
It's quite a, uh, time consuming process but, um, it's worth it.
And then after that you want to sand down the edges with a, uh, with a file.
So it is set in and that was my original plan for the bits that I built up.
But then I decided to change it later on, uh, to snakes as you will see.
So to shape the forepacks, uh, I got a log that's roughly the shape of my arm.
And then, um, so as you can see there, roughly the shape of my arm.
Uh, then basically bend the forepacks over a bit.
Uh, and here we are just using a clamp to basically bend out the bit that, uh,
is going to be flapped to the shield.
So there it is.
Then we go over to the log, bend it round.
It won't bend too, too well, uh, but once you, um, attach it, it will, uh, it will bend really well.
Then, uh, I wanted a beveled edge, so we just went along and beveled it up.
Uh, quite easy to do.
Uh, just don't brush it and, uh, it will be really good.
Just go back on it again after you've done what, done it once.
And, uh, here is your finished product, product.
Now for the, uh, the archive grip, they have these, um, eyelet hooks.
So I'm drilling through and one thing that I don't like that I have seen in other how-to's
is they always leave the screws showing.
Um, but what we're going to do is we're going to attach them
and we're going to go back over with wood filler to hide the screw holes.
So they are, they're just little, um, I think they might be used to hold piping.
Anyway, here we are, um, attaching the leather on the inside with the Elmer's spray glue.
Uh, I do believe that we switch to another one, um, but Elmer's does work fine as well.
You do have to wait a bit for it to, uh, to harden, I believe.
Again, quite a time-consuming process, but if you just go through it,
have patience, it will learn what they are.
And, uh, yeah, a huge, uh, thanks to my dad, um,
as I definitely wouldn't have been able to do this by myself.
And, uh, he has helped me along this journey for, um, a long time.
Uh, overall, probably about 50, 60 hours of work went into this,
so it's not a small weekend project, that's for sure.
Uh, you'll be left with a few creases, um, but that shouldn't be too, too bad.
Um, also, I'm sure the Greeks would have had some creases,
and it's pretty much impossible not to.
It's mainly just smoothing your hand over the glue,
pushing it down, trying to push out any air that could, uh, form the crease.
So, there you are.
Let me just cut around the edge, and then we're just using a scalpel to, uh,
re-cut out the holes that the, um, the little ringlet eyelet things will go through.
Just basically poking it across until you get a fairly decent hole,
and then, um, just poke, poke them through, and screw it up on the other side.
re-sand them down, because you don't want it to show when you're smoothing it, if you don't mind.
Here we are on the outside, and, uh, we said that the glue method wouldn't really work,
so actually what we did, uh, was use, uh, staples.
Um, this actually works, uh, remarkably well.
Basically, you pull it tight.
At first, we just sort of got all areas of contact.
Um, you will have to pull out a lot of staples, uh, just to let you know.
Um, but yeah, basically, you go along for a long time,
just staples, staples, staples, unhook a staple, pull it tighter,
put a staple down, uh, but it really, really works.
Um, as you can see, it's already taking a shape, just from that amount of staples.
Um, but it ended up really nice.
Again, lots of this is having patience, um, as you can see, we've also already attached the
paw packs, uh, so basically, we just use, um, screws again, but then I got these decorative
bronze, uh, covers that I cut off to make it look more, uh, authentic.
So yeah, as you can see, it's pulling it tight,
putting down a staple, pulling it tight, putting down a staple,
removing a staple, pulling it tighter.
Um, it's very repetitive, uh, was a bit boring, but it was definitely worth, um, doing it.
I couldn't really see any, uh, any other way to do it.
Um, but yeah, so just follow along.
Not too, too, uh, too hard, but it does the job.
Uh, also what we did after this, um, is we did one whole thing of staples,
let it stay for about 24 hours, so that's the amount of staples that we put in,
and as you can see on this side here, it turned out really smooth,
but wait about 24 hours and then redo it, where the leather then relaxes.
Now for the design, I chose a gorgon design, this works for anything, um,
I just got a projector and projected it on, and then as this has a gold outline,
I used a gold permanent marker or sharpie, and, um, I just went around.
So yeah, basically you don't have to do this design, obviously it's whatever you want,
but I would highly recommend using a projector.
So here I am, just tracing it around, um, and then for the paint, uh, I used,
uh, it was actually metal paint, unfortunately I didn't film any of the paint job,
but here it is after, um, the permanent marker.
So yeah, basically I, acrylic paints do work, but they wash off,
so yeah, I used, um, like a metal paint, and it worked really well.
Um, it takes about eight hours to dry, and I did about two to three coats of it.
For the rim, um, it was a lot of work actually, uh, so this is just after I did my design,
which is very satisfying to watch, um, but it was actually a very long process,
so, um, as it is just wood, I couldn't really coat it in leather,
um, so I sprayed it with about three coats of Rust-Oleum Filler Primer,
then I sprayed it with a matte white, about four layers,
and then I used the same black paint that I used for the, um, Gorgoni Medusa thing,
uh, for this, and then I used painter's tape, um, to peel it off, and it is very satisfying.
Now you may think if you decide to do triangles that it might
be a little bit difficult, but don't worry, I've done the math for you.
So there are 37 total triangles around the front, so there's 77.5mm on the top,
and 70mm on the bottom. Now that should be a guide, and on the back side,
they're slightly bigger, so it's 77.5mm at the top, and 64.5mm on the bottom.
