How to setup a Target Archery Recurve Bow

LEARN ARCHERY
7 followers
6 Video Views·Jul 11, 2025
In this video we take an in depth look at the set up of an olympic style recurve.
We look at all the steps for getting it out of the box to setting up the clicker (and everything else in between)
*Bow assembly
*ILF Limb fitting
*Checking Brace height
*Setting the tiller
*Limb alignment
*Fitting the arrow rest
*Fitting the pressure button
*Setting the centershot
*Fitting nocking points
*Fitting the sight
*Fitting the stabilisers
*Checking the balance of the bow
*Fitting the clicker
Good morning, I'm James, one of the techsperts from Merlin Loughborough, and today we're
going to be putting together a target recurve set up, exactly the same as if you'd come
in to buy your first bow.
Right, we'll start by unboxing our bow, start with the riser, it's a Maibo Rio riser, in
a lovely matte black, it has a few tools and instructions with it as well, we'll get
to know what to do for later, there we go, on to the limbs, I've set in my bow Synergy
limbs, they come with little rubber protectors on the end so they don't rattle against each
other, and then, two limbs, other item we have here, string, all very important.
Right, we're now ready to put our bow together.
We'll now assemble the bow, the riser has a dovetail unit in the bottom, and the back
of the limb has a dovetail on it to fit into that, the bottom limb is marked with a sticker,
sometimes the limbs have lower and upper written on them, or top and bottom, the dovetail goes
straight into the socket, and the U goes around the limb bolt.
Top limb, that just drops in in the same way, and now we come to stringing.
Right, now we're going to string the bow, just before we do that, it's worth pointing
out that this movement in the limb is perfectly normal, and we'll discuss that in further
detail when we talk about tillering, getting the tiller set on the bow correctly.
The string has a big loop and a small loop, the big loop goes at the top, and slides down
the limb, the small loop goes at the bottom, goes onto the limb tip, into the string groove,
where it will end up, then we need a stringer, which has a pocket at one end, which goes
on the bottom, just make sure that's safely in the groove, drop the pocket on, at the
top there's a saddle, a little rubber non-slip bit on the inside, that goes on the limb below
the string, we put our boot on it, pull up, slide the string onto the end of the limb,
and relax down.
If you're struggling, you can put two feet on it, it brings it closer to you, and if
you're really struggling, you can tie knots in the stringer to make it shorter.
To de-string it, it's the reverse process, boot on the strap, saddle at the top, slide
the string down the limb, and then have one de-strung bow.
Now a quick check to make sure that the string is correctly positioned in the string grooves,
and we have one strung bow.
Now we've got the string on the bow, we're going to check the brace height, that can
be measured from the throat of the grip to the string, or from the string to the back
of the pressure button.
If you have a bow that is over-braced, it becomes slower, if you have a bow that is
under-braced, it becomes a little bit quicker, but also sounds like a bag of bolts.
This is a 68 inch bow, where we'd expect to have a starting brace height that can be tuned
later of between 8.5 and 8.75, this currently has a 9 inch brace height, which is a little
high.
So what we're going to do is take the string off it, take some twists out of the string,
and put it back on and re-check.
Right, we've taken the string off the bow, we're just going to take some twists out of
it to correct the brace height by lengthening the string.
Back on the bow and re-string, check the measurement again, it is now reading 8.75, which is what
we were aiming for.
The next job is to set the tiller on the bow.
This is basically a method of measuring how strong each limb is relative to the other.
We measure it from where the limb enters the riser, to the string, and compare the difference
between the two.
Obviously in this instance the bottom limb is significantly heavier than the top.
The reason we need to have a little bit of tiller on a target set up is because we shoot
one finger above, two below, up here where the arrow is, and the centre of the bow is
down at the throat of the grip.
So we need to put a little bit of tiller on to account for that.
If we were shooting bare bow, with three fingers underneath, we're now pulling in line with
the grip, so we would have zero tiller.
This bow is currently set at 3 eighths of an inch tiller, which is a little bit high
for a first set up.
We typically like between an eighth and a quarter of an inch of positive tiller, with
the bottom limb stronger than the top.
The tiller can then be adjusted through tuning at a later date.
To adjust the tiller, we need to use the allen keys that came with the riser.
In the case of this rear riser, there's a big allen key for the limb bolt on the front
and a small allen key for the locking screw on the back.
Before I adjust it, I'm going to take the string off again so that we don't run the
risk of damaging the limbs.
In this instance, the bottom limb is stronger than the top limb, so we need to put a little
bit more poundage on to the top limb.
We'll do that by adjusting the tiller bolt and changing the limb angle.
This increases the poundage just by a little bit.
The side effect of this is you can actually use these limb bolts to change the total poundage
of the bow.
It is not recommended that the tiller bolt is purely there, as the name suggests, for
adjusting tiller.
What we'll do is we'll loosen the locking screw on the back.
Of course, we need to take about an eighth of an inch of tiller off.
I'm going to tighten that bolt by about half a turn, nip the tiller bolt back up again,
and restring.
Now we've done the adjustments, we will just recheck the measurement.
We now have a quarter inch of tiller, which is fine for a starting place.
At this point, it's also worth just double-checking that the locking screws are secure, because
we don't want them vibrating loose while they're being shot.
The next job is to check how straight the bow is.
This is not hugely critical when you're getting going, but the better you get, the straighter
your bow wants to be.
What we do is we just have a little look down the string, lining it up with the tiller bolts
at the bottom, and checking that the limb tip is coming straight off the end.
This bow is beautifully straight, it has to do both ends, so there's no adjustments required
on this one.
If there was, we utilise our little Allen key again, and the screws in the side loosen
off on one side, tighten up on the other to move the limb left and right in its pocket
to adjust any slight tolerance anomalies that we have with the limbs.
Now we're going to fit the arrow rest.
Today we're using a MiBo Hotwire rest.
Just take him out of his packet.
This is a highly adjustable arrow rest, so the wire will move up and down, and in and out.
We shall look at that in a second.
We'll just peel the backing off it, and we shall apply it to the riser.
Drop it down so that the hole lines up with the hole for the pressure button,
and then apply pressure to it to get it to stick.
We're now going to put the pressure button in.
The pressure button is a device that allows us to tune the arrows.
It's got a spring in it that applies the pressure to the side of the arrow
to correct the archer's paradox and get the best flight possible.
That screws into the riser at the pressure button hole,
sometimes called a burger hole, and will then correct the centre shot in amount.
Right, now we're going to set up the centre shot.
Before we do that, we need to have a little discussion about arrows.
There is a huge range of arrows you can get from very big fat aluminium ones
down to little tiny carbon and carbon alloys.
Selecting the right spine arrow for your bow is very critical.
And a massive topic which will take some discussion at a later date.
For the purposes of this, we're going to use a Maibo Flight,
because they are conveniently all the same diameter, no matter what spine they are.
So, what we do, we set the arrow onto the string,
sit up against the pressure button,
line the string up down the centre of the riser,
and see where the arrow lies relative to the string.
We want the arrow to be sat just so that the point is to the left of the string
for a right-handed archer, obviously the other way round for a left-hander.
This one needs to come out just a tiny little bit,
so we shall find my allen keys.
To adjust this, we use the collar on the button,
loosen the collar off, move the button so that we get the centre shot we desire,
tighten the collar back into the bow,
take that off so I don't stab myself,
and then just tighten the collar back up again.
Now we've done the left and right adjustments with the pressure button,
we need to do the up and down adjustments to get the arrow to run in the centre of that pressure button.
At the moment it's running a little bit low,
so what we do is we use the very small allen key that comes with the arrow rest,
into the screw at the back, loosen that off,
that frees the wire so that we can move it up,
and I'm going to move it out just a little bit so it holds the arrow nicely.
I'll just tighten that back up again, and we are done.
While we're talking about arrow rests and pressure buttons,
I want to discuss how to adjust the pressure of the pressure button.
That is done with this little locking screw here, we loosen that off,
that means we can adjust the plunger itself at the back of the spring,
like that.
You take pressure off if the arrow is too stiff, and put pressure on if the arrow is too weak.
You can also take the button apart,
and change the spring inside it to give you the best arrow flight possible.
Now we've got the arrow rest and pressure button on,
we shall put the knocking point on.
So we take our brace light gauge back again,
clip that onto the string this time, and position it on the arrow rest.
We have already set the tiller at a quarter inch,
so we will set the top of the bottom knocking point one quarter inch above square.
We take our knocking point's tying thread,
our length, we want it to be reasonably long,
we want to have something to hold onto to pull the knots tight.
We'll thread it on so that the first knot sits at the quarter inch mark.
Just a simple knot, until we get it in the right place.
This of course, as with everything else, will need tuning out with experience.
Pull it nice and tight, get rid of the brace light gauge, it's now in the way.
We just put knots on the top and on the bottom.
I like to do six knots, three on the top, three on the bottom.
Give the last one a good tug.
This material is particularly good because it melts well.
With a lighter, we'll just melt the end off,
square it off with the thumb.
And the same on the other side.
And then we shall put the top knocking point on.
Now for the top knocking point, we'll use an arrow to measure the gap required.
We don't want to go right up against the knock,
because we need a little bit of room for when the bow is drawn back.
A tight angle appears there, and we don't want the arrow being squashed by the knocking points,
which might lead it to be knocked off the arrow rest.
So, same process again, nice tight knots,
and again six knots here.
Keep the tail nice and long so we've got that to pull up on.
Remove the knot so we don't burn that by mistake.
We don't want to take the flame too close to the string,
because we don't want to melt the serving, or worse, still set fire to it.
One complete knocking point.
Right, now we come to attaching the sight to the bow.
I've gone for a typical intermediate level sight, the Avalon Tech 1,
with a carbon extension.
The sight block slides up and down the front by pressing the silver button.
And there's a micro-adjust up and down on the top,
and a micro-adjust left and right at the sight.
We remove the sight block from the extension arm.
He's going to be mounted to the side there, over those two holes.
Inside the bag we have
a couple of screws.
We locate the bracket over the two holes, put in the screws,
and tighten up using our Allen keys.
Now the block's mounted, we slide the sight into it,
secure it at the desired length,
take the sight pin,
that slots onto the front, and tightens up.
Now the sight's mounted on the bow,
we can turn the sight pin until we get
somewhere close to the centre shot.
We typically want the sight pin just to be to the left of the string when lining the string up down the centre of the riser.
When you're shooting with a sight, if your arrows are going off to the left,
you move your sight left, and if they're going low, you move them low, etc.
Basically, follow the arrows is the rule.
Now we're going to look at stabilisers.
Most people, when they're moving to an intermediate bow, will only have a long rod to start with.
The mass weight change from a beginner bow to an intermediate bow is
quite a lot, so they may want to keep that weight down.
The purpose of stabilisation is to provide
weight a long way from the bow,
to give stability, so you're able to hold on target easier.
A set of stabilisers is typically made up of
five components.
Extender, which mounts straight into the bow.
A V-bar, which then becomes the stabiliser mount where the other stabilisers will mount onto.
That secures
into the V-bar, into the extender.
The long rod mounts into the front of the V-bar,
pointing towards the target.
Then we have two side rods that mount to the side of the V-bar,
pointing towards the archer.
There we have a complete set of stabilisers attached to the bow.
Right, now we've got a full set of stabilisers attached, we can check the balance of it.
First place is just below the grip.
Check the left-right and
side-to-side balance, as you may be able to see there.
It's slightly heavy on the side-to-side,
which is not that much of a surprise.
It's currently a little bit top-heavy, so we need a bit more weight towards the bottom.
We also like to find the centre of gravity going front-back.
In this instance, it's about an inch in front of the throat of the grip,
which is pretty much perfect.
So the weight distribution front-back is correct.
We just need a bit more towards the bottom, and a bit more on the opposite side of the sight.
Right, to correct that slight lean off to one side,
I'm just going to put a weight opposite the sight, so we'll take the cap weight off,
put another base weight on,
and re-secure the cap weight.
That should then give us left-to-right balance.
And by doing that, I also seem to have corrected the
front up-down as well, by adding a little tiny bit more weight.
The last part of a target archer's set-up is the clicker.
It's basically a draw-length check, and is usually not recommended for someone
just coming off a beginner's course, but will be something a coach would suggest you put on
6, 8, 12 months after you've started shooting.
The first part that we'll do is the clicker extender,
which goes in the front of the riser. That came with the riser.
He just screws in. Some bows have a little plate
that screws on instead. Today we're just going to use an Imaibo
Crescent clicker. Take him out of his tube.
He screws into one of these two holes on the front, depending on
what length we need.
And mounts onto the bow.
As your arrow comes through, it'll give a pleasant click.
Finally, the operation of the clicker.
The arrow slides underneath it, and onto the arrow rest as normal.
As you draw the bow back, the arrow will come along the clicker.
For the last little squeeze through,
the point through the clicker, and the click, you can let go.
And release your arrow as normal. The clicker needs to be
set-up to your draw-length, and needs to work for you, not against you.
It's best to have a coach's hand to do that, to make sure
you're still shooting the bow the same way you were after you mount the clicker,
as you were before. That pretty much concludes the set-up
of a full Olympic-style recurve rig.
Happy shooting. Goodbye.
