How to Make a Survival Bow and Hunting Arrows

Crossbows Legacy
11 followers
6 Video Views·Jul 8, 2025
Well, you have already seen what today's video is about, we are going to make a bow in conditions.
It was something that had been promised to you many years ago, easily two or three, if not more,
when we made a very simple one with two sticks, but it was more like a bushcraft project, like something playful.
We are going to try to make this a survival hunting tool as such, but hey, the meaning of survival will be that it will be
all made with materials that we take from the medium and the only tool that we are going to use for this is going to be a survival knife.
In this case I have this really cool knife, it is the Spyderco Respect, which is so far the highest-end knife I have had.
But if you are interested, if you liked only what you have seen, stay to see the video because I am going to tell you
the way in which you can get one totally free. Let's go there.
Well, first of all we are going to start by doing what will be the body of the bow itself.
We will look for a section of wood that is long, straight and with a thickness of between 3 and 6 cm in diameter.
In this case I am going to do it with hazel, since it meets these characteristics and I had located a couple of fallen branches that were still green,
so the wood would be in good condition. As I said, anyway, I use this species because it is common in my area,
but if in your case it is not like that, a quick Google search will tell you other suitable woods to make bows.
Okay, now we clear both the piece of wood itself and its surroundings and we can work with it.
As always, in all this cutting, it is better to leave less material before we lose our hand and then we get short.
So I take the whole branch and I will decide which exact section looks best for the project.
Taking care of how straight and uniform it is, I am getting more or less to the idea of which part I will finally use.
Here, as you can see, it has a knot from a branch that came out and this makes that part of the fibers of the wood to be irregular and useless,
so, well, with this it already delimits an end of what the bow will be.
I cut just below this one and I would only need to cut the other side.
Now we are going to look for the center of the stick. With a rope it would be as easy as extending it along this one and then folding it in half,
but assuming that we had not yet manufactured it, this other shape that I show here can be done.
I make a mark, four fingers below the center and another four fingers above it.
This is going to delimit the area of the handle itself.
Before starting to carve, it is very important to see the natural curvature of the wood.
Once we have it in mind, we make sure that the inside of said curve is facing us once we stab the bow.
This face, which is closer to us, is called the belly, while the face oriented to Diana is called the back.
The carving that we will do now will be to avoid that all the torsion of the body of the bow is concentrated in its central part,
as you can see what happens in this branch that I use as an example and ends up breaking.
What we will be looking for is that the ends of the branch curve in the same way as the central part.
To achieve this, we will begin to refine the blades along the belly area.
This recess must be progressive and along the bow, going from less from the center to more recessed towards the tips.
It is very, very important not to carve anything on the back of the bow,
since these fibers are the ones that will withstand the forces of tension when shooting
and the marks that we can leave in the carving would make them much more susceptible to breaking.
Therefore, as I said, on the back of the bow the knife will not touch it at any time.
It is important to check from time to time to make sure that the recess we are making is still regular and progressive
and as I had already said before, it is better to go little by little and take a little longer than to go over,
give a machetazo of more and have to start the bow again from scratch.
Having reached the middle of the trunk, as this brown mark indicates here, which is the marrow of the branch,
I leave this blade for the moment and start working the other.
Once at the same point with this other blade too, I check and detail the work to make sure that it has been good before letting the wood dry.
You have to be careful if we are going to let it dry in the air,
since having carved only one of its faces, the wood will tend to curve in this direction,
leaving us the bow with a slight U shape if we do not prevent it.
And preventing this will be as easy as looking for a straight surface where to be able to support the bow.
We place some heavy stones on it and thus they will prevent it from deforming as it dries.
If it was really a situation in which I wanted to make the bow as soon as possible,
I could always try to speed up the drying by putting it on a bonfire or a source of heat
and making sure that it does not deform on the march.
But come on, being realistic, in a survival situation we would be looking for firewood, water,
improving shelter and a thousand other things before wasting time drying a bow,
while this can be dried alone or that, being in the sun.
After a while and with the wood already dry, we can start doing the first tests
to see its flexibility and continue carving as a consequence.
If we can no longer lower the belly of the bow much more, because we do not have wood left there
or it will be very thin, then in the same way we did with this one,
we begin to lower the sides of the blades.
As you can see, as I said before, the back is still untouched and we do not risk
even removing the bark of this one.
As we lower one blade, we repeat the process on the other.
We will test its flexibility and lower it again in the areas that bend the least.
As you can see, the bow is already taking a very regular and symmetrical shape,
so before taking the risk of confusing me with a shovel and carving more in the one that is not,
I prefer to use a piece of charcoal to differentiate both.
It seems silly, but already with several hours invested in the project,
it is not difficult to prevent the destruction by a misfire.
In the same way, we can use this same piece of charcoal to mark the areas that need more carving,
and make sure to be more precise in this.
When we get closer to the final level of flexibility of the blades,
we can start making the notches at their ends to place the rope.
Now you are going to see me use a synthetic cord,
and do not worry because in nothing we will see how to make a natural rope from scratch,
but being realistic, except for a very elaborate rope,
like with tendons or some animal skin treated,
a natural rope will give us much worse results in terms of durability for this task.
Therefore, it is always a good idea to carry a couple of meters of artificial rope
in a survival bracelet, as we saw doing a while ago.
But hey, if you want me to make another version of that bracelet,
and much better, you can also tell me in the comments.
Now, being able to leave the bow in tension with the rope,
it will be easier for us to see the symmetry in the way the blades bend,
and thus be able to work on these.
Here you see me already giving the last touches to the bow,
and although for a carelessness a blade I have a weak point too flexible,
more or less you get the idea that the final product is what we are looking for.
But nothing, let's go there with the natural fiber rope that I had told you.
In my case, the easiest way to get these is from the stem of the orchids,
so we will look for an area where there are large ones and we will take several.
To avoid burning our hands for their stinging hairs,
we can leave them submerged in water for a while,
although it will always be a better solution to pass them through a cloth,
thus making a little pressure, and let it be the one that neutralizes them.
But hey, since here the idea is to use the minimum resources,
let's go with the first method.
After a while, I can already take them with relative security and start processing them.
Using a stick or something similar,
we will start to crush the stems of the orchids a little,
until we see that the fibers that surround them begin to make a magic of detachment.
Here I rub a little everything with the stick,
because being very large orchids,
many of their hairs had survived the bath and were pricking my fingers.
But hey, we keep crushing the stems a little more,
and we see that the fibers begin to separate.
So we get comfortable, well seated there,
and little by little we are going to spend a good time peeling all the orchids we have.
We try to remove these strips as thin as possible,
but nothing happens if they are short,
because later we are going to use them too.
Now, with all the peeled orchids,
we will take the fibers and begin to divide them longitudinally,
to make them as thin as possible,
within a reasonable measure, more or less,
as you are seeing now on the screen.
We will have to let these fibers dry a couple of days in the sun,
or in the same way that with the bow we can bring them closer to a bonfire,
and in less than one or two hours they would also be dry.
Being dry, they have this other aspect,
that as you can see, they remain a little more shrunk,
but they are still just as resistant.
We will take a handful of these,
all of them in the same direction,
and we grab the center of this one.
We orient both halves of the handful in the same direction,
and we begin to turn one of these.
Then, we turn this same end on the other,
but in the opposite direction of the one we are turning on itself.
We repeat the action with the other end, and so on.
When they shorten, we can add more fibers,
simply placing them next to the ones that already had that side.
If this explanation has not been very clear,
and you want to see a video in detail about it,
you can see it by clicking up here on the right.
With a little time and a lot of patience,
our rope will begin to take shape.
Choosing good fibers and doing it carefully,
can end up with a relationship between its resistance and its thickness
more than acceptable to be a rope like this
that we have made only with natural materials at one time.
These are some meters that I made years ago,
once I wanted to test how much rope I could make from scratch in one afternoon,
and well, here you have the result.
Here I break a piece of the one I made at that time,
so that you can get an idea of its resistance.
Let's take a short break,
and I'll tell you a little bit about this rope
that you have been seeing since I started working.
As I have already told you,
it is a rope from the American brand Spyderco,
that we have seen others on the channel,
but this one is different from the others in one aspect,
and that is that the previous ones were made in Asia,
and this one is made, it says it right here,
in Colorado, in the United States,
so I think that today,
of all the knives I have seen and tested,
it is the knife that has the best finishes.
I mean, it is totally symmetrical,
even the biggest detail is amazing.
You see, a very aggressive blade style,
super pointy, I love it,
I love this tip,
between the Province, the last one we tested,
and this one, and the Respec,
I'm starting to appreciate even more,
if I didn't do it enough,
the sharp tips for mountain knives.
And well, I have to tell you that it also comes
in a very high-end steel, a pulvimetallurgical steel,
the CPM 154,
which is a steel with which
we won't have to worry too much
not to say anything about the rust,
unless we do something extreme,
it retains very well,
and it has a more than acceptable
hit resistance, so well,
you've already seen it, you'll see it,
and the edge is perfect.
I'm telling you that after making the bow,
I'm recording this once I've finished everything,
it still cuts like crazy.
It also differs from the Province
by a much better grip,
I already told you it was a hit on the previous one,
this is a G10 handle,
which completely hides the edge of the knife,
it can help us in cold climates,
so it doesn't transmit the cold to our hands,
or whatever, but it's very comfortable
in all grips. It has a guard here,
but it doesn't bother us too much
if we want to make a more advanced grip,
taking our index finger to the edge of the knife.
And while it's not a Bushcraft knife
by design,
you can see that this is almost
for finishing, to defend against dangerous animals,
or whatever,
even if it's a Bushcraft knife,
you'll see how well it performs
in a field knife in general.
I'm sure the most curious of you
have already downloaded the link,
you've seen the price,
and it was around 500€.
I might like the knife,
but it's a very high price.
I understand not everyone can spend
that kind of money on something like this.
But the guys from Spyderco
are doing a giveaway,
and to participate it's easy,
you just have to subscribe to their newsletter.
I mean, put your email,
your name, and a couple of other details
so that when they release offers or news
you'll get those notifications.
Just by registering,
I mean by subscribing to this newsletter,
you'll enter the giveaway of one of these.
With the bow and the rope ready,
let's start with the arrows.
First of all,
we'll look for straight and regular branches.
As I said at the beginning of the video,
in my case, the most abundant option
is the hazelnut.
I'm picking dry branches
to save me the process of drying them,
waiting, and so on,
but picking the green ones
we could even use them to straighten them on a fire.
I've picked a lot,
and then I'll keep the more uniform ones,
I think this is the most practical.
To make the notch where we'll fit the bow rope,
we'll start working on one end
with a clean cut.
Now, with the tip of the knife,
we'll separate the fibers of the wood
with vertical movements.
And then, with horizontal movements,
we'll cut these fibers
to create the hole itself.
We'll start on one side,
little by little,
and as we get to the middle of the branch,
we'll start on the other one
until both notches are in the center.
You can see that I've made this one
very deep,
because it will be the one that fits the tip of the stone.
For the tail of the arrow,
it would be better to make it half deep,
so that it fits the rope.
Before making the tip,
we make sure that the whole stick
is smooth and without irregularities.
We can straighten the small curves
that the branch has
by doing a little force in the opposite direction
and holding it for a while.
With patience and a lot of care
not to break the stick,
we can achieve very good results in a few minutes.
This would be better
by wetting a cloth that we would place
in the folding area and putting it on the fire,
thus leaving the wood more malleable.
But as I said, I'm doing it here
without cloths or anything, with minimal resources,
and there is also the option of wetting the stick
and simply putting it on the fire,
but it is much less practical and efficient,
so I stay with the first one I said.
Ok, with this ready,
now we can move on to the tip,
and in this first arrow we are going to make
a devastated stone tip.
For this, we go to an area where we can find
stones of many sizes and shapes,
and we will look for the most flat and thin ones of small size.
If there are not,
we can break a larger stone by hitting it with another
and keep the fragments that come out of this.
Now, we will look for stones
that have one of their faces as flat
and smooth as possible.
These will be the ones we will use
to devastate the smaller stones that we have just taken.
Here I find a couple of them
that meet these characteristics,
but they do not have the surface large enough,
so with this other
and the first one we had seen,
I go more than served.
We select the small stones
with more potential for tip,
and we just have to start rubbing.
You have to be careful
with the pressure we apply,
or as you can see,
we load the stone.
This was at the beginning of starting,
so I do not mind starting again from scratch,
but what happens this,
when you have been rubbing the stones for an hour,
it can be devastating.
So little by little we are giving shape
with patience and a lot of care,
and you can imagine that yes,
this has been a long time.
With the general shape ready,
I move on to make it thinner,
rubbing more carefully on the smaller stone.
It has to end with the right thickness
to fit in the notch we have made in the stick.
We are getting closer
and as we have spent more time
investing in the tip,
we are more and more careful
that, for whatever reason,
but please do not split.
Once it is fitted,
with the knife we lower a little
the exterior of the stem so that the shape of the tip continues,
and now yes,
super careful,
we start to carve some notches
on both sides of the tip.
We start with the vertex of a large stone
and we finish with the sharpest vertex
of that stone or any other.
We repeat it on both sides and that's it.
Fitted again in the stick,
we can start to fix it with the ant fibers
that we have left over from the rope.
We turn it several times
and we tighten well to make sure
that it is well fixed.
And although it could be ready
to use the tip,
we are going to reinforce it a little more
covering the union and protecting the fibers
with resin glue.
This way, much better.
But of course, how do we make this glue?
Well, very well, we will start with a bonfire
from which we will take carbonized wood
that is usually left on the edges.
Placing it on a stone,
we will use a stick to create
charcoal powder.
It is important to grind it very well
and that it is powder, not just small bits.
Then we will have to improvise
a container that resists the heat.
I have taken a shell,
which we can find in any coastal area,
but we can make a clay container,
use the ass of a soda can,
look for a stone with a cava,
whatever comes to mind.
With this one ready,
we have to take pine resin
and we will put it on fire until it melts
and is completely liquid.
At this moment, we can start
adding charcoal powder while we stir.
We will add more and more
until we notice that the mixture
begins to thicken too much.
It is likely that we have to
reheat the resin more than once
until we can add all the necessary charcoal.
Once ready, we will spread
the end of the stick in the mixture
so that the glue stays
stuck to it. We spread, cool,
spread, cool, until we have
all the glue that we put in the container
already adhered to our stick.
This glue has a point
before it hardens completely,
which allows us to mold it as if it were plasticine,
so it is ideal for the use that we are going to give it now.
With almost all the arrow ready,
we just have to put something
on its tail to stabilize it in flight.
Seeing the primitive of the rest of the arrow,
we are going to go with feathers.
These can be found scattered
on the ground of the forest or, as was my case,
in the remains of the dam that would hunt
a fox or a mountain cat.
Without much problem, I got feathers
to make a dozen arrows,
that, just from that place.
Before starting with these, it is convenient to identify
which ones are from which wing of the animal,
since the edges of the feathers
of its left wing and its right wing
are oriented in different directions.
But hey, with this already known,
we take three feathers of the same wing
and cut them longitudinally.
We make sure they have the same size
and we can start fixing them to the arrow.
To do this, we will start by turning
one until it is fastened.
Then we add a second until it is fastened
and we can put the third
and turn the three at the same time.
We will also have to make sure
to fix them all in all their length,
with the idea that they allow us
a maximum number of shots before releasing
and having to do that again.
Finally, we cover and reinforce
the ant fibers with glue
and that's it.
But hey, between the tip, the glue
and everything else, you already see
the huge amount of time we have used
to make this arrow.
And while it can be the most primitive,
the most purist, in the sense of bushcraft,
being realistic and speaking of a survival situation
as such, now we are going to see
a much better alternative, in my opinion.
But hey, before, one last detail,
and that is that when putting the feathers,
it is necessary to leave a free face
where the body of the bow will be when shooting,
so they will not be crushed at each shot.
And now we go with what I consider
to be a realistic survival arrow,
that is, the one I would do
if I needed it.
Again, we take a more or less flat stone,
but now, instead of sharpening another stone
with it, we are going to sharpen something
that we always have on top, some keys.
Without the fear we had before
that the stone would break, with the key
we can tighten with all our strength
against the stone that we are devastating
and it does not take long to notice the devastation.
Yes, the key is much harder than the stone,
but we also have to devastate less,
so in the end we take half the time
of what we take to make the tip of the stone.
And it is that this one is not only more sharp,
but as I have already said,
it is much more resistant to impacts
once we are using it,
and it is also much easier to mount on the arrow.
To do this, we will simply make
a perpendicular cut in the stem
that reaches half of it,
about 3-4 cm from its end.
We remove the wood from there to the tip
and it would almost be ready.
We have to lower the edges of the stick
as we had done with the tip of the stone
so that the shape of the key follows a bit
and we would only have to fix it.
Now we will use something
that I always recommend to carry in the backpack
and you have already seen in other videos
that I even carry in my wallet,
and this is American tape.
We will take a not very large piece
and we will take a thin strip of this
with which we will give the first fixation to the key.
Here we can leave it very tight
without fear of breaking the tape
by tightening it well.
After this first strip,
we cover everything with a couple of wider turns
and that's it.
It has taken us literally minutes
and it is much, much,
much more resistant than the previous arrow.
Now, to stabilize this arrow,
we put the tape back
creating two squares of about 8x8 cm
and we place each one
on one side of the arrow.
And it would be working.
As soon as we cut the excess,
we give a little shape
to the front of the fins
and we already have that.
A way to stabilize the arrow
that will last us dozens and dozens of shots.
Ok, and now there will be some
but Pablo, if it is the situation
in which we have lost all our arrows
with keys and tape
and there is no other option than using
more simple natural materials than the first arrow.
Well, there are a thousand to see,
but we are going to see now one more,
a third option that complies a little with this.
Everything has been said, it complies with this
based on being, I think, the least effective
of all we have seen.
But hey, if you want to be like this as a project
to have a good time in the field and shoot some shots,
this is ideal.
We will start by giving a quick tip with the knife
to the bow of the arrow.
We will place this tip on the embers of a bonfire
and as the wood begins to carbonize,
we will remove it
and devastate it with a stone.
So we can give it shape
while we remove the burnt wood
and only the hardened by the fire remains.
We finish with the knife to the detail
and so simple, tip ready.
Now, for the stabilization of the arrow,
we are also going to show a third method
and we are going to take the short fibers
that we had left over from the antlers.
We will join small handles of these
that we will fix with more antler fibers
to the body of the arrow.
Little by little, we are leaving
more and more clogged that area
so that it creates air resistance
once the arrow is wrapped.
This is the disadvantage of this arrow
that when making resistance
will always slow it down much more
than the two previous stabilization models.
Likewise, it could already be used
but as we have done the previous times,
we are going to finish it with glue
and now we already have our three variants
of survival arrows.
With a minimally powerful bow,
any of these can serve us for small
or even medium-sized prey.
But hey, let's see them fly now
once and for all.
Let's try it now, let's see how long it lasts
or if it lasts.
I think that only because of the force
that has to be done to tighten it and loosen it,
it will have a power more than considerable,
enough to make it a useful bow.
And nothing, let's go there.
Well, we already have the bow here,
everything ready.
You see there a target about 8 or 9 meters,
a bottle full of colored water.
And nothing,
let's start with this arrow,
the most practical primitive survival arrow
that we had seen.
I think it went through the hole
of the bottle and broke the rotten wood
that was next to it.
Second attempt,
the arrow has survived without much damage,
the glue has lifted a little bit,
but little more.
Let's see.
Well, the feathers in this second shot
have come off completely.
Let's try now with the tip,
this is the realistic survival
that I said,
the tip with the key.
They are all going to the left,
I don't usually shoot with a bow.
Now, finally!
Oops!
From side to side.
Now I'm at 4 meters,
a little more maybe,
because this is the most fragile of all.
And if we have already loaded one of them,
I don't want to load this one
at the first failure, so...
Oops!
Although the accuracy is bad,
you'll see how fast they fly,
they fly like lightning.
This one broke.
It broke the tip as expected,
but it held much more than I thought.
Let's remove this one in the middle
and make long range shots.
There it is.
Take that!
Look!
A hard watermelon.
The skin is very hard,
and as you can see,
it went from side to side.
We have a trunk there,
at about 25 meters,
and this is a big target,
so it doesn't affect my accuracy,
but we can see the range and power.
Let's see if I hit it,
of course.
First shot, from 25 meters,
the whole key went in,
it's a...
Oops!
It's a fallen tree,
the wood is not in the best condition,
but it hits hard.
Second shot,
from 15 meters,
I hit it, and from side to side,
you can see the tip,
what a great bow.
The bow is doing great,
I'm very happy with it,
and it's a shame because I want to publish the video this week,
but there are many more tests I want to do.
I want to weigh it,
to see how many pounds it is,
I want to see it in an open field,
shooting with parabola,
but I think I'll do all of that
in the next days or weeks,
and I'll post it on my Instagram,
so if you want to know more about the bow,
you can find it there or in the description.
Also, remember that in the description
you can find the link
to participate in the giveaway
of the Spyderco Respect,
subscribing to the brand's newsletter.
I really hope you enjoyed the video,
it's been a long time since I worked so much on a video,
so all the support in the comments,
liking the video,
sharing it with your friends,
I'll appreciate it a lot.
That's all for today, see you next time!
