Making A Twisted Mug - Part 1

Ceramic Art Studio
35 followers
Jul 7, 2025
Hey everybody, welcome back to Matthew Kelly Pottery. I hope you are doing well today. We're talking about twisted mugs or twisted pots
I know earlier this year or late last year
I talked about faceted bowls, which are very similar to these but these twist a whole lot more than those bowls did and
Be honest with you. They just look cooler and who wouldn't want a mug that's twisted
You know bowls are great
But mugs and number one you can see more of the twist in this because it's more vertical and people use mugs all the time
And so anyway, we're gonna cover that
I had lots of questions on my Instagram about how I make the piece how I do the handle
So I'm gonna make a couple videos on this this one today is gonna be about how I throw the basic shape
Facet it and twist it. So let's go
I'm starting with a pound and a quarter to make this mug
My normal mugs that I make or anywhere from three quarters to one pound of clay
These need to be a little bit thicker to carve the facets in them and twist them
Also, I need to leave extra clay in the bottom so that I can come back later and trim a foot on them
And so there's several different reasons that I need the extra clay
Plus I'm not too worried about making the lightest mug in the world
These definitely end up heavier than my normal mugs, but they just look so dang awesome that I'm like, all right
We're just gonna make
Make them a little bit thicker so that they can survive so that I can do all the alterations that I'm doing to them
But anyway, you can make them at any size you want but this for today's example
I'm gonna make it out of a pound and a quarter and
Most of the process of the very beginning is is the same as always
Centering the clay opening it
Then I'm also doing the dual angle for this video
So I hope that helps with you guys, but I'm gonna try to keep my head out of the way of the overhead camera
This clay ball is a little bit stiff. So but that's okay. I
Learned a few things. I'm just making the faceted bowls and then now making these mugs. I've learned a few different
Tips and tricks that I I think will help
Some of those probably are going to change over time
But for now, I've learned a few things that definitely help like I said number one
I'm gonna be carving a foot in these later. So I'm gonna leave the bottom a little extra thick
So I've probably got a half inch there on the bottom so I can get a nice
Healthy foot carved in the bottom of this
I'm not going to open this up real wide because my goal is to make a really tall
A tall skinny cylinder that has some some thickness to it
So open it up to about there and then I'm gonna
Pinch it back in
From here. My first pull is kind of gonna be like my claw pull
Just to kind of even those walls out from where I pinched in. Okay, I am gonna do
one more pull I
Like to bring in as much of this clay at the base as possible
So I'm gonna do one more pull just
my kind of traditional pull
But I'm not I'm not trying to eat not trying to thin it out too much
Just trying to even out a little bit of that clay that's in the base there. I
Want to leave a whole wall of the pot at least this thick and that's probably
Probably 3 8's
Maybe maybe a half inch thick at the base
Now I want to make this skinnier
and taller
first I'm gonna use my rib to cut away this extra clay at the base because all that's gonna be cut away later even if
I don't cut it away now, so it's just easier to cut it away now
Started the base and pinch in
This is gonna it's a form of a pull, but I'm not really
Just moving that clay in and up
Without really thinning out the walls. If anything, they're making getting they're getting a little bit thicker by doing this
the first faceted bowls and twisted mugs I made I
Would do the faceting
Carving all the way from the very bottom all the way to the very top
And I found out that that caused a few issues later on that I didn't like
number one making the rim very uneven and
Easily it would it would tear easily when I was stretching it
So I like to leave the extra thickness there at the top and also not carve my facets all the way up
Also in making the foot later on
If I start my trimming all the way at the base or my faceting all the way at the base
It also makes the trimming more difficult
So one of the first tips I'll give you is that when I get this really skinny thick cylinder
I'm actually going to come up from the base
Probably a good half-inch about the thickness that I that I left the base in the inside
And I'm actually just gonna separate some of the clay there and push in so that this clay here at the base is where?
I'm gonna I'm gonna later on make form my foot from the trimming at that point there
I'm just gonna use my rib to kind of smooth up the hole outside here
All the way down to that point there
Okay
Get all the excess water
I'm not too worried about if there's water on the inside because I can get back to that here in just a minute
Now there's different tools that you could use to facet
these the two of my
My my two favorites are
This rounded loop tool here. I really like the way this because that gives me a lot of smaller facets
And then they twist into these really tight
Swirls like this the other one you could use is any kind of a wire tool like this
This one is really nice. It gives you a wider facet
You could still get pretty tight twists with that
But it it tends to get a bit more uneven in the rim and the shape of it kind of twists a bit
because of being
wider facets when you go to stretch that you have a greater
Difference between the thickness in the wall from where you've carved to to the edge of that carving. So
it's it's it's funky and they and I found that when I do this one when I stretch it out the the
Thicker parts of the facets tend to rip a little bit more. So if you like that kind of like ripped look
Then that happens with that a bit more so you can just try different ones, but I'm just going to take this for this example
I'm going to take this rounded tool
Loop tool here, and I'm just going to carve vertical facets all the way from from this point right here above that foot all the way
And I'm actually going to stop
Probably about the same about a half inch from the top
Right there because I don't want to carve and make the top uneven, especially with these being mugs
I want the top to be somewhat even so that it's easy to drink out of
And you don't like go to pour it and you know drink out of it
And it spills out the side because it was lower over there. So anyway, so and I'm not trying to carve too deep
I just want to make a decent facet
and
So I'll turn that to the camera over here so you can see what I've carved so I went all the way from there to there
And then I'm just gonna follow that all the way around go right next to it. I don't worry about trying to leave
if you can leave a little bit of
Surface area in between them or you can just carve them right one next to the other
I like to get a whole bunch of these facets carved into one piece
So I don't really leave much in between now
obviously
if it's skinnier up here than it is down here, then you're going to have a little bit of space in between the facets down
here and
Sometimes there's a little bit of space at the very top where I pull away with the tool
So there's a little bit of that
But like I said all that kind of gets twisted in so you don't have to worry so much about that
I'm also probably carving a little bit deeper at the very bottom than I am when I get to the top
And I like to like
Clean out this tool every time after I finish that try to get this excess clay out of the loop because otherwise
It actually will leave some of that behind on the next one that you carve and just kind of makes a mess
So clean it out pretty good in between each
Trim
Facet that you carve
All right, and then hopefully you end up somewhere in the range of doing them evenly
But also that's not that big of a deal either
I haven't actually tried this too much without smoothing these but what I've been doing is after I do that
Come with my sponge and smooth up the because they're gonna stretch out quite a bit as it is
so I like to come around with my sponge and
Smooth the edges
Just spin the wheel
slowly and
Just kind of wipe up
And get all those little burrs off the outside
Now from here, obviously, I don't want to touch the outside with my hand
But I want to go on the inside and I want to stretch that out and one of the motions
I like to use is I'm stretching that I'm gonna I'm really gonna use a lot of down pressure and I kind of push in
From the top and really push out and down and so you're stretching that clay, but you're also forcing it down
and really just
Forcing that clay to twist but first I have to get a little bit of water on the inside
Just have to drip that down my fingers
And then I put my left hand on the inside
and then just
Really aggressively push push down
And then I want to before I get too aggressive on that I want to I want to bring this top back in
Because I gotta remember this is gonna be a mug at the end and so I've got the basic shape already done
But I can twist that even more from here because I want to bellow that out
Add a little bit more water like just run that water down my fingers and get it on the inside there
All right from there now. I'm gonna
Go to that point
Bellow that out right there a nice little belly
Now a lot of times the top does get uneven but because I didn't carve it all the way to the rim I can come
back and
Take that little top off
Thin that rim out just a little bit. So you got a really nice drinking rim
Go inside with the sponge and get the excess water out
and like I said, these are a bit thicker than a normal mug, but
Normal mugs look like that
not very many so
There's the the first one and you can see there where I've started carving from
is is right above that and this will give a
Nice even place to come back later as I as I trim that foot on it
Like I said, I'll just do that in the next video
But and you can see I could have pulled a bit more at the base because you can see on the inside there
Yet it definitely has a lot of thickness in the base
But I also want to be able to use a lot of pressure as I'm stretching that from the inside
So I can get that really nice swirl
I mean, I don't know if I could measure but that twist there probably goes all the way around does at least one full rotation
If not, you know close to a second full rotation and you can get them really tight
In the twist. So let me grab another clay ball. We'll do one more
Maybe I'll do one with the wider faceting tool to show you that one and then we'll call it
In watching this footage back during editing
I did realize something that I think I wanted to mention here and that is that the the aggressive twist that I get in these
I'm pretty sure it comes mostly from the down pressure. I apply from the inside on that first initial
Stretching that I do from the inside
so if you try one of these
Keep that in mind and try to try to apply a lot of pressure on that first twist or first bellow
From the inside with a lot of down pressure and I think that'll help you out. I
Think I have noticed that the the skinnier you make the cylinder the more dramatic the twists are
Because obviously you're stretching the clay more the skinnier the cylinder is to start with you're stretching that wider
I have tried stretching the one of these with a throwing stick and it did work. I didn't get as
Exaggerated of a twist in it
I think maybe the drag and the down pressure of my hand being able to feel exactly where I want the pressure
help with that I
Mainly tried the throwing stick because I wanted to try the to get the top not to widen out as much
Because they were gonna be mugs
And like I said, it turned out. Okay, but I still kind of prefer doing it with my hands
So now I'm gonna take this wire tool, which I'm sure you've seen one of these before
Wire stretched in between this curved metal and I'm just gonna start at the base
Just like I did there and I want to pull all the way up and I'm gonna try to stop
This one the last one I did I actually carved all the way to through the rim and you can do that and it makes
The top kind of uneven and if you like that, that's an option
but you can otherwise you can stop right there below the rim kind of like I did on the last one and still have a
little bit of
Unbeveled or unfaceted clay up there to make your rim out of
But I kind of like this because I don't have to hold a wire tight in between my hands
I can just hold this in both of my hands just push in there at the base and
And I like it when they fall away
I'm done so you can see there what I've done and I just try to get a similar width
All the way up go right next to that one and start my next one
These wider facets are a bit harder to
Even out when you get to the end because by the time you get to the end you may have a wider space
Than you plan to have also just carving them. It's just harder to to keep this steady
But then again to these pots aren't meant to be
Your normal like perfectly thrown a
Wheel thrown pot so kind of looking now. It looks like I've got room for two more facets
I like to kind of look ahead when I get near the end
There we go
Now you can see those facets like say much wider than what I carved before
But we'll act very similarly by the time I twisted here so
Or some of that water down on the inside and
Here we go
Decided to exaggerate the belly on that one a little bit more you can see how uneven the top got on this one compared to
The other one, but like I said, I have enough
Leave enough clay there that I can
And these are not going to be very big big big mugs, but you know you can make them
Out of more clay. I've done some out of a pound and a half and those definitely worked
But I also didn't want to make really heavy mugs either
So you can see there how what I mentioned that the really wide facets kind of tend
To rip a little bit more and also it all depends on your clay
But you can see those facets there as they stretched especially there at the base the clay ripped a bit more
Which you know it's really kind of nice to embrace that that rough kind of look as long as you don't mess that up later
moving the pot around you kind of try to
Protect or preserve all that rusticness there even as I trim the foot on the base there, so
There's the wide the wide facets
There's the skinny ones
And like said this you hope this helps, and I hope if you give it a shot. You know let me know how it goes
I'd love to see
Anybody can send me images through Instagram
on the messaging side of Instagram if you give it a shot, I'd love to see what you come up with and
Yeah, we'll be back again for another video on
carving the foot and or cutting the foot on them and then
Putting the handle on because that's another test that these handles that I put on these take
Even more time than my normal mug handles, but I really like the way those are turning out as well
And so thank you guys for being here, and we'll see you soon. Bye
