Throwing and trimming a pasta bowl | MAE CERAMICS

Ceramic Art Studio
35 followers
1 Video View·Mar 24, 2026
AI Generated·May contain errors
Hey folks, good morning. Lily here from Made Ceramics. Today I am throwing pasta bowls,
so they are sort of wide, wide shallow bowls. I'll just go and grab one and show you.
So this is a pasta bowl. You can see it's really wide, really flat. I like to trim
a little foot ring into it so that it sort of sits up nicely. But yes, essentially it's just
a lovely flat bowl. So I am going to throw these and show you what I'm up to. Tomorrow I will trim
them, maybe the day after depending on how dry they are, and I'll show you that too.
Right, so to start with we have two balls of clay here. This piece of clay is actually far
too much, I think I need this much. I need a chunk of clay, this maybe is 200 grams,
and then this guy is 1200 grams, so 1.2 kilograms, and this is going to be the bowl.
We are going to be throwing on a bat today, so this is because when the piece is thrown,
to take it off the wheel is quite a mission and distorting the piece. So you throw on a bat and
then you just take the whole bat off. So I'm going to show you how to attach a bat ring,
and then the bat, and then throw the bowl. Before I start actually throwing, I like to just get my
ruler and my calipers and I work out the size that I need. Next step, get going. So
this step is just like if you were to throw a plate or something, you just need to flatten
this ball of clay. So that's it, doesn't matter if it's not completely centered,
but it does matter if it is kind of wobbly on the top, you just want it to be nice and flat.
And then we're just going to make a little spiral and extend to the back.
Now you just pretend that this is the wheel here and start. So I am using really soft
reclaim here and I have wedged it all, but as it is reclaiming, I like to just give it a few
cones up and down to make sure that it is nice and de-aired, nice and wedged, just in case there's
some last little air bubbles hanging out in there. You just kind of get rid of them with a few good
cones. So you want to center your clay sort of low and flat so that you don't have to work so
hard in the next point, in the next kind of step. Now we're going to open this up and bring the
balls up. I'm going to just really compress in here, not just to sort of avoid s-cracks and
things like that, but also to sort of get a really nice inner profile. So I'm sort of pushing out
in a bowl kind of shape with my inside hand and my outside hand is really just supporting it,
making sure it sort of kind of goes up rather than all the way out
at this stage. If you go out too far then you're just going to keep going out and it will eventually.
So now I'm going to just kind of clean up this inside shape a little bit more
and then it's done. If you want to, you can measure this here. So I like to make them to
six centimeters and that is where it is. And so it's done, the bowl is finished for this stage.
Now we're gonna get this guy, I don't know what this tool is, spike on the stick,
and we're gonna run it underneath the bowl, get rid of some of this excess clay, but mostly it
provides a spot for the wire to kind of pull the bowl off. And there we go. For me, I like to use
more clay, err on the side of having too much clay and too little clay for wide shallow bowls.
And that's because if you are using, I don't know, say too little clay and you need to get to this
kind of width, it actually needs so much on the bottom here and so much to support the shoulder
if you're coming out. And if you're thinking, I'm trying to think of like a ramen bowl,
it's got a nice big shoulder and it comes up still quite high. This shoulder is a really
important part where it needs to sort of support the weight of the clay above it. And if you go too
wide too quickly, then you're just going to find that it falls down. So I like to err on the side
of more clay and then you can trim into it later and get something like a foot ring. This is my
scraps bowl. As you can see that, you can see that this foot ring,
kind of in proportion to the rest of the bowl looks really lovely. And we've got the shoulder
that I was talking about supporting all of this clay. But when I threw this, it would have kind
of just been like one big block of clay down the bottom. So I will show you how to clean this up
when the piece is leather hard, which will be probably two days from now because this is so
much clay at the bottom. But we'll keep an eye on the rim. If it gets too dry, you might just want
to put a little bit of plastic on there. Or you may, what I tend to do is tomorrow I will flip
it over so it starts drying on the base rather than the rim. So yeah, that's this point and I
will see you in a couple of days. All right, folks, it's been a couple of days.
This is the bowl that I threw. It's at leather hard stage. So if you're new to pottery, that
means that it's still wet. But it's obviously not sort of squishing under my fingers as I'm touching
it. So you can see I've just made these little marks with my fingernail. And so you can mark it,
you can probably if you want to sort of mold it a little bit, but it's holding its shape. So it's
the perfect time now to trim it. So I'm going to show you now how I do it. So I have my
bowl here. I have the sponge and some water. I'm just going to wet the wheel here and then put
this guy down on it. And you can sort of line it up with the circles that are on your wheel
to centre it. Then you just want to check that it's in the middle. This guy is slightly off,
so I'm going to move it just. So now it's in the middle, I'm going to tap it down,
sort of create a little bit of a seal. And then I'm running my, between where the rim of the pot
meets the wheel head. So like this, but I'm doing it at my sort of six o'clock. Now I'm going to
do a bit of an initial sort of tidy up of the base. Now I'm going to mark with my calipers
the inside trimming line. And this just guides me so that every bowl that I make is the same.
So now I can use this as my guide and I will trace the line here to be my inner
foot ring measurement. And then I'll do another one on the outside that would be my outer foot
ring measurement. So I'm tapping the base of the pot to sort of hear how thick it is.
So there's a different tone and that kind of tells you how much more you can trim before
going through the base. And it's just practice to sort of work out what the tone means. You can
also sort of see a little bit of movement if you're getting a little bit too thin.
So I know I've got a little bit more that I can work with there. This bit is kind of
a little funky, but I like to just use a really wide path and sort of turn the wheel on slowly
and then sort of twist the other way and kind of pull it as well to try and get the wheel off
and unstuck. So that was it. Here she is all finished and looking nice. So this is a
beautiful little shallow bowl that can hold nice things like curries and things, salads, pasta,
soup if you're brave. So this is a shiny white glaze that I use. It's quite nice.
You can see sort of the freckles in the clay. Hey, it's a voice over me saying for no good
reason I forgot to record this outro. So here we are. I hope you have enjoyed this video of me
making a bowl and please like and subscribe and I will see you next time. Bye.
