hand sewing an 18th century round gown

Pre-modern Women's Fashion
182 followers
30 Video Views·Jul 7, 2025
in this video, we take a look at how fashion evolved into the 1770s round gown, how the sewing techniques used affected fashion, and finally, hand sew the dress. This sort of round gown is made like an english gown with sewn-down pleats at the back. It was a remake of earlier 1740s fashion and often used that era's fashionable silks! It was basically the retro fashion of the 1770s! I made mine using the original techniques using a silk brocade in the 1740s style.
For further reading and patterns:
Hello and welcome, I'm Maria from Sew Through Time and this time we're taking a deep dive into 18th
century fashion and we're going to make a round gown from the late 1770s or early 1780s. Before
we get into the actual making of the gown, we are going to take a look at first 18th century dress
making in general, how the making of the garments affected the garments and the fashion, and then
we'll talk about the fashion, how it evolved and how it came to this era's round gown. To start,
we kind of have to go back and look at the 17th century and the dress making traditions of that
era to get into why dresses were made the way they were in the 18th century. In the 17th century,
most dresses were made by tailors because they had the constructed bodies or corsets built into the
and because of the structure of garments, they were definitely a male-led garment industry and
they were made by tailors because most of these bone bodies would require a lot of hard work and
that was considered more appropriate for men because it's physically quite taxing to actually
get those needles to go through all of those layers of fabric. Tailors were a highly valued
and highly skilled guild and to become a tailor, you had to apprentice for many years with another
tailor and then take the tailor's exam to be accepted as a guild member before you could
qualify for actually taking commissions and work on your own. And because these bodies evolved
very much at the same time as male garments and male garments bodies evolved, the structural
and elements and the techniques are very similar. So that's why tailors would make them and they
were made mostly patterned flat and then fit onto the person's body. And that's how most female
garments were made for most of the 17th century. But in the late 17th century, there comes a new
fashion called the mantua gown. And this mantua gown is just a loosely draped piece of cloth
basically that is pinned in place to form the actual gown. And it has much less structure to it,
it's much more loose as in it has flowy skirts, it has drapery, it has a lot of different elements
than was traditionally in tailored garments. Still women did wear bodies or stays or corsets
underneath, but those were typically a separate garment. And the mantua gown would be a gown built
on top of it and then it would have the stays underneath and then you would have a stomach
or piece covering the gap. And because this new mantua gown with its drapery required a very
different set of skills than was typical of a tailor with its flat patterning, a new job evolved
called a mantua maker. And mantua makers were mostly women. From the mantua gown and the
mantua makers themselves comes a completely different way of making gowns. And this evolves
during the 18th century first into the English gown. The English gown, also called the nightgown,
was basically at first just like a mantua except that it didn't have the draperies on the skirt bit
but instead would close in the skirts. This was very much influenced by the robe volante,
which was another different kind of early 18th century gown that later evolved into the robe
a la francaise or sackback gown. The reason why we have two different names for these garments
is that basically English and French fashion were slightly different, though they did influence each
other and you do see French fashion in England in the form of sack gowns and you do later on
especially see English backgowns in France. But the terms were different. So a robe a la francaise
is the name that they would use in France and a robe a la anglaise or English gown would be the
French term for the English backgown. In England that would be called a nightgown and then the robe
would be called a sack gown. So that's why there's two terms. They can be used interchangeably now
but English people would be using nightgown and sack gown and no a nightgown doesn't actually
refer to it being worn at night, that's just the name of the garment in English. Whereas in French
you would use the terms robe a la francaise and robe a la anglaise. The reason why in modern
language English gown is much more common than nightgown is simply because the word nightgown
means such a vastly different thing than it did in the 18th century. That evolves basically from
the mantua and it can be closed or it can be open in the skirts and in the 1740s it also evolves
into the round gown where the skirt is closed but it is not closed the same way as previously in
some of the mantua gowns but instead it is closed as in it has the petticoat built into it.
In those previous English gowns the front would close the same way as on this robe volante
so that basically the front edges just meet. I don't know how much of this is survival bias
but at least according to the examples that we mostly see nowadays most of these round gowns
were expensive brocades so I'm guessing that the reason why they had the round gown
was basically to save fabric so you wouldn't necessarily do it on cheaper material if you
could afford a separate petticoat and the open English backgown. The round gown seems to disappear
by 1750s and this is also when there is no more the mantua gown it has clearly evolved into the
English gown and that is open in the front. So the way a mantua maker would work is first the
client would get their stays made by the tailor the stays are the corset of the 18th century
they are no longer called bodies like they were in the 17th century and when she is standing in
her stays then the mantua maker would drape the fabric over her and make the basically the dress
on her body. Of course the client could go home and while she's sewing but this is basically
how the gowns were made and this sort of dressmaking technique leads quite naturally
to pleating different sorts of things so to get the fabric to sit on the body. So these pleats
could sometimes be sewn down as in the English gown or they could be left loose as in in the
and basically these two gowns with some variation are what is fashionable for several decades there
up until the 1770s when we start to see new gowns evolve. Around this time several things in fashion
happen first of all the hair starts rising off the head and becoming really big and also the
gowns instead of having a separate stomacher in the front they start closing all the way
and as that happens the round gown makes a resurgence. At this point I want to point out
that there are also a lot of other gowns and a lot of other styles that become fashionable at this
time but I'm going to be focusing now on just this part because this is relevant to this video. If
you guys are interested I could make a separate video on how fashion evolves and what the
so let me know in the comments is that something you'd be interested in and while you're at it
please like this video if you are enjoying it. And though gowns are still often trimmed elaborately
you can definitely see that they are getting much more simple than they used to be in the past.
So a round gown makes sense in that point too because if you're not really looking for a bunch
of fancy trim at the skirt fronts where those gown edges are open then it makes sense that
why don't you just make it into a round gown instead. And of course it also saves on fabric.
There is a lot of earlier 18th century gowns that get remade in this era into this newer style but
there's also a lot of gowns that are just made with the old silk because fabric is very expensive
so people might have some laying about and then because of the simpler fashion even if they don't
have enough for a full robe a la francaise they can make the simpler round gown out of it. And
that's precisely why I made a round gown out of this fabric. This fabric was a gift that my husband
got for me for our silk wedding anniversary. I was kind of persistent that I must get silk for the
wedding anniversary. So when we were in London we went to Gold Hawk Road and I could choose
anything I wanted and I chose this silk brocade and it is so gorgeous but it was extremely expensive
so I just simply couldn't get enough for a robe a la francaise. I got three and a half yards and
that was plenty enough for this. My two main inspirations for this are also round gowns that
use silk that is clearly earlier from the mid-century and because the sewing machine hadn't
been invented of course all of these gowns were hand stitched. So since these garments evolved
with them being hand stitched the way these are made it often doesn't actually make it much faster
to use a machine. So that's one of the reasons why I'm going to be completely hand sewing this
because actually the only part where I could actually save time really by machine stitching
it would be the long skirt seams. With everything else it's so quick and efficient to just hand sew
it that it doesn't actually make that much sense to try to use a machine for them. Back in the 18th
century a mantua maker could make an English gown or a round gown in 12 hours. I'm not sure if I
made this in 12 hours, probably not, but I made it on and off again in less than a week. And though
these sewists were extremely skilled they wouldn't waste time sewing anything unnecessarily small
stitches or being too careful in places where you didn't need to be careful. And also because fabric
was extremely expensive garments were often altered to fit either your changing body or
somebody else's body later on. The secondhand fashion was extremely common in the 18th century
there was huge markets for secondhand gowns. So these different reasons led to garments being
made quick and efficiently in a way that it was as easy as possible to take them apart when needed
to but they would stay together. So you would use strong and minutely precise stitches only where
necessary. So a part where the stitches show onto the outside you wouldn't use fine stitching.
But then on an inside part especially one that does not carry a lot of weight you would use big
sloppy stitches and that was the way they did it then. They wouldn't necessarily see it as a bad
thing like maybe we would consider it nowadays. They definitely saw it as a practical thing. So
if you see me doing neat stitches in some places and big sloppy stitches in other places
that's simply because that's the way the garments are made. You don't want to waste your time on a
thing that doesn't need really precise stitching. Here is my version of the Isabella McTavis
Frasier gown and I'm using this as an example to show you how 18th century gowns are made.
The way these are made is that this lining is draped on the body and made to fit the body
and then the rest of the gown is constructed over the lining. So basically if you have a fitted
lining that fits you, you can basically make any sort of fitted back 18th century gown using the
same lining. On the other hand a sat back gown's lining is slightly different from this. So
basically you can take any 18th century gown pattern and get the lining and get the lining
to fit your body and then you can construct any sort of 18th century gown over that lining. Since
I made this gown I've actually gained a little weight and this is also wool so it stretches a
little bit on the body and so since I'm using now silk I'm going to be making a new master pattern
that fits my body better and that is going to be then my master pattern for any other future 18th
century gowns I want to make. Here is my new and improved English gown or fitted back 18th century
gown pattern and this battered back piece is based on my Italian gown that I made in 2020 when I was
quite a bit smaller than I am now so I enlarged it a little bit and then changed the shape a little
bit because I want this to be a fitted back not an Italian back gown and this one is my Isabella
McTavish Frasier gown's front and I changed it a bit to fit this slightly earlier style better
and also to give myself more bust shape because I'll be using silk instead of wool so it won't
have as much give in it. How I came up with this improved pattern is basically just swinging it.
I took the pattern pieces and just drew it based on my assumptions so we will fit this lining on
our body and then make any changes that need to be and that will be my new master pattern for 18th
century fitted back gowns.
And here's the first try of the lining. I'm not too concerned with the back because
the that looseness is just I can take seam allowances in a little bit but the front is
too big at the waist so here I'm pinning it onto my body to change that line and with it pinned
into place I feel like the fit is pretty good. There is some puckering at the underarm but that's
mainly because the seam allowance is still up there. I'll redraft and cut that front piece and
then I think we're ready to go.
I measure my back length in my stays and bump pad and then cut that out of the fashion fabric.
Then I place the back lining piece on the folded fashion fabric so that the upper edge of the
lining piece meets the fold line and at the bottom there's a two inch gap. Then I draw that line.
Then I backstitch along this line.
Okay here's my natural waistline marked and here's the end of the lining and then
this is the two inches that it goes further back so we'll cut this line from here diagonally to that.
Then press that seam flat. Then I pin my lining to the fashion fabric so that the center back
seams match and from the fashion fabric side backstitch into that seam.
Then I pleat down that fashion fabric onto the lining to form those back pleats that make an
English gown an English gown. The back construction stays the same throughout the 18th century
but the thing that changes is the width of those back pleats. Earlier in the century they are wider
and later they get narrower and narrower until the 1780s when they can start facing
inwards instead of outwards and eventually become seamed back pieces of an Italian gown.
Then I trim off the excess from the bodice sides leaving the fabric
wool full width from the waist down. This will form the back half of the skirts
and then the back pleats get sewn down with a prick stitch. This is basically a back stitch
but just with a very small stitch taken in the front and with a longer stitch taken in the
back side. Next I cut the bodice front pieces to match the lining pieces using those leftover
pieces from the bodice back that I just cut off. Then I pin the fashion fabric front pieces to the
lining pieces to make sure everything stays flat and smooth while I stitch. Then I fold the seam
allowances towards each other and pin it in place making any necessary cuts to get that
neckline to lay smoothly. I do the same to the bottom front edge and make sure that the pieces
line up properly. And then I hem stitch along the flat edge of the bottom and along the center front
edges and along the neckline up until the point where the shoulder straps attach. And then I draw
out the pattern piece for the shoulder straps and cut them out of the lining fabric first to test my
pattern out. I'm using the mock-ups of my front pieces to eliminate fabric waste. And then I base
the shoulder strap linings onto the back of the bodice so that I can check the fit. If you're
fitting on yourself I find it easier to base the back on and fit the front on yourself by pinning
and if you're fitting it onto somebody else I find it easier to base the front on and then
lay it smoothly and then pin the back on to the person. But before we can fit the shoulder straps
on we need to make that scary cut. We cut along the back bodice lining edge in a straight angled
line towards the center back not quite reaching the center back so that we can pleat the back of
the skirts onto the bodice. Be careful to keep the angle right so that you don't end up making your
gown short-waisted and make sure not to cut too deep so that those back pleats don't rip that you
already made. To ensure this I cut a little ways away from the waist and then check the pleating
as I go and then cut the necessary bit that is still remaining. Next I pin the bodice front and
back lining pieces together right sides facing each other and sew them together with a running
backstitch. And backstitch the shoulder strap lining to the bodice back. And after making sure
that it fits properly running backstitch the front of the gown to the shoulder strap lining.
Next making sure that the fabric stays smooth pin the front bodice fashion fabric over the
over the bodice back making sure that you follow that curved line of the lining fabrics.
Okay otherwise it looks pretty good but the neckline as you can see is way too high. I have
marked with pins where I need to like cut it down to and then fold it again and re-sew that.
The shoulder straps are looking good and I'm holding the skirts because I don't want to put
too much weight on them because they have that cut already made so the fabric is kind of fragile
there so I don't want to tear it so I'm holding it but other than that it looks really good.
Then brick stitch the side seams.
Now it's time to pleat the skirts. Shove that edge of the fabric where the back pleat happens
in between the lining and the fashion fabric. It doesn't need to be nicely done just so that
looks nicely from the outside. The skirts get pleated all the way up until the side of your
bodice. You need to measure this on your body to make sure that it's in the correct place
and as you pin these in place make sure that the fashion fabric seam allowance is turned to
the inside and that the lining fabric is left loose both now and when you sew on the skirts.
And then we re-hem that fixed bodice neckline
and then I backstitch the skirts to the bodice. Because this part is under a lot of stress
I use a thicker silk thread for this part and also because my silk brocade is rather thick
and there's many layers of fabric I do it like this instead of the regular way working from
only one side of the fabric because simply otherwise the stitches would be much larger
than I intended them to be. Now on the free front portion of the bodice seam allowances are folded
towards each other and pinned in place and once you reach the portion with the skirts just the
lining fabrics seam allowance is folded to the inside and pinned in place. That very back tip
there might be a little fiddly and if you need to cut some of it away then you can do it now.
And now all of that gets hem stitched in place with the visible bodice front bits with small
neat stitches and the part where the skirts are with bigger sloppier stitches. Making sure to
take a small portion of the skirt into the stitch but because we're making a round gown not an open
English gown we still need a skirt front panel. Measure the correct length on your body with your
stays and bum pad in place both at the front and at the sides and if there is a difference make that
adjustment at the top of the skirt not the bottom. For me that meant cutting an angle that dips at
center front two inches from the sides and then the hem is cut straight.
And then this newly cut skirt front piece gets attached to the back piece. I start by pinning
them together remembering to leave a 10 inch pocket slit at the top and stitch them together
with a running back stitch. I make a narrow hem for the bottom by folding up the fabric twice.
Unlike in the Victorian era this era's hems don't really have a lot of structure to them
so you don't need a large turnaround or any sort of hem linings or anything like that,
unless of course you're making a trained gown in which case you might want a hem protector.
The fashion of the late 70s and early 80s wasn't actually for trained gowns but rather they would
often be short enough to show the ankles. This front skirt portion gets pleated onto a linen
tape waistband. So you mark onto the waistband tape the center of the waistband and also the
sides where the skirt ends. You make a big box pleat onto the middle and then pleat the sides
to match the length of the skirt waistband. You can just eyeball these, these do not have to be
even, there's several extant garments that do not even have the matching amount of pleats on
both sides of the skirt. And then I baste the pleats in place to make sewing them later easier.
Then I sew them to the edge of the waistband and then fold the waistband over to the inside
of the skirt and hem stitch it down leaving all the raw edges onto the inside.
And then I prick stitch the seam allowances on the pocket slit edges down for a clean finish.
And then I draft my sleeves based off of the patterns of fashion one and six. Here's the
sleeve, I took it in a little bit here at underarm but other than that it looks pretty
good. It's a little long but because there's going to be that fold line here I don't think
I want to take anything off because this will, this has the seam allowance so it will shorten
already because of that. So I think we're good to go. Remember to make any necessary
adjustments to your master pattern and then cut the fashion fabric and of course the lining if
your mock-up doesn't work as the lining. Now put your sleeve lining and fashion fabric together
with the wrong sides facing each other and then flip the lining front edge to match with those
lining back edges and pin through all three layers. And next you'll sew in a running back
stitch through all three layers. Fold that fashion fabric over that seam that you just
sewed so that now all the raw edges are encased in the sleeve and pin in place.
And then sew closed with a prick stitch.
The bottom edges seam allowances get folded in towards each other and stitched in place.
Then I baste the underside of the sleeve onto the sleeve edge but only the underside,
not the portion that is on the shoulder strap and you'll see soon why. Okay and now the bottom
edge is basted on and now how we do the top is it gets sewn on top of the shoulder strap. I'm
first going to baste it on but basically it just gets placed here on this strap and then you pin
it and then baste it and then there is a bit of excess in the back and that is going to get pleated
down and the reason for this excess in the back is simply so that you have the full range of motion
so that you can put your hand up that disappears once you put your hand up. The way I like to fit
these sleeves when I'm fitting on myself is I use my knee as kind of my replacement shoulder
and then just make it smooth on that and then that will make it smooth on my shoulder as well.
And last test to make sure that we have the full range of motion.
And now the under portion of that sleeve gets stitched down with a back stitch and for the
upper portion, the one that is on the shoulder strap, that gets sewn with a running back stitch
on the outer side of the garment. And next before we can sew the fashion fabric shoulder straps on,
we need to make a neck back piece. This will cover the raw edges of that top neckline
and then that gets prick stitched in place. And now it's finally time to place that shoulder
strap fashion fabric. Again I use my knee to mimic my shoulder so that the fashion fabric doesn't
pull weirdly on the shoulder line. I fold all the raw edges onto the inside and make sure that those
previous stitching lines get covered by the fashion fabric and then I prick stitch it in place.
Okay now one last try with everything sewn on and I'll need to make a light, a slight correction
here. The strap placement was a little wrong so that it started gaping there at the neckline.
So just a tiny tuck in and I'll sew that down like that and then it works. And now as for the
because the sleeve is a little long here. It's supposed to have a little tuck at here,
here at the elbow crease so that first of all it will make
bending your elbow easier but also slightly shorten the sleeve.
And so that will keep the elbow like slightly bent,
make it easier to bend elbow. And then I decided to also tuck in this sleeve because first of all
the lining was showing a lot and second of all it's slightly long still. So if I tuck it in like
this that will create much nicer sleeve.
And here is the final look. Those sleeve flounces and the neck tucker
are separate pieces of lace that are sewn onto a linen tape and then basted onto the gown. That
way they can be taken off for cleaning or added to another gown or maybe changed for another pair.
And because body modesty as we know it nowadays didn't exist yet,
that lace tucker was considered enough to fill that low neckline.
