Ceramic Review: Masterclass with John Jelfs

The Story of Ceramics and Porcelain
9 followers
May 22, 2025
Made in four separate parts, potter John Jelfs takes us step-by-step through the processes he uses to create a complete functional teapot for issue 306 of Ceramic Review.
Learn alongside this master potter with an in-depth guide - plus uncover many more masterclasses, glaze recipes and techniques - by becoming a subscriber: https://www.ceramicreview.com/subscribe/
Film by Layton Thompson
We mix our own clays, we always have. I have basically six bodies that I use here.
A mixer of ball clays that we blend together, we've got an old dough mixer that we use,
it's over 100 years old actually and I nurse it, it's got like gold dust. We have a very simple
glaze that is down to simple local clay and ash, just two ingredients. We get the clay from
one mile outside the village that is a stream of black clay that runs diagonally across our
riverbed but it works really well in our ash glazes and also in our iron slips. As with most
potters, there's something really, really nice about making pots with materials that are around
you, it's very exciting. Just taking the crudest of raw elements and sieving them, refining them,
blending them into a glaze. The important thing in making any pot really is to compress the base
well, if you don't want those S-cracks to appear. So the first part of throwing, opening out the
clay is to put a nice bit of pressure on the base, the base is then finished. Then it becomes a
cylinder, as so many pots begin as a cylinder, so that's how I throw them, a straight cylinder,
then I fold the top in, I leave a good thickness of, a good solid amount of clay where I'm going
to form the rim that the lid sits on. I have a sponge on a stick that initially I used to use
just to get the water out the pot because my hand, once you close the top of the pot
you can't get your hand in, you need to get the water out. But what I suddenly, what I became aware of
quite a few years ago was that I was actually using that, not only to get the water but actually to
form the pot. This is a piece of boxwood ruler and I use that to help me form the outside.
For all the pots I make I have a series of these wooden gauges which are bits of ruler
that I've been using for years. I use that to form the actual gallery that the lid sits on,
but I also use it to measure the width of the opening in the pot so that I get the lid to fit
well. When I cut them I use a twisted steel wire, that takes a bit of air underneath the pot when
I'm cutting it off, it makes it much easier to lift off the wheel. When I'm throwing the lids
it basically starts off as a bowl that I turn back on in on itself. To be practical a teapot
is something we want our customers to really get to like them, so they've got to work well.
It's no good if a teapot you buy is dripping everywhere or it's not comfortable or the
balance is all wrong. When you're pouring tea you don't have to hold the lid on and do this
kind of nonsense, you can almost turn these actually upside down that the lid's going to
catch, so the lids tend to stay put. The secret of that is not to make people have to turn the pot
upside down to empty it, also to give the teapot, the lid a decent skirt which sits well inside
the pot, brings the centre of gravity within the pot, if it's going to rock it's going to
rock on this corner and it's not going to fall off, that's important. The knob on the lid is
thrown separately when I'm assembling the pot.
I tend to throw the spouts off a hump because there's no problem with the s-cracking,
throwing off a hump the only problem with it is you can't really compress the inside of
a pot when you're throwing off a hump because you press down and the clay just goes sideways.
When I throw the spouts I tend to put them onto a sheet of formica or you could put them onto a
wooden board that's got some polythene on it, something that isn't absorbent, that enables the
the spouts to remain soft and yet the tip of the spout will dry off a bit and enough for you to
handle, to apply to the body of the pot. I like to press the pots, the spouts onto the pot. With
practice, with experience you get to know your clay and a wet spout can go on a slightly drier
body quite happily. It's important to know your clay, there's this thing that when you're throwing
a pot on a wheel you're automatically putting a bit of torque into the clay and if you look down
on your wheel, my wheel rotates in an anti-clockwise for throwing an anti-clockwise direction
so you're actually holding the clay back, you're holding it back in a clockwise direction looking
down so when you, when the clay relaxes it wants to go the direction the wheel was going in which
is anti-clockwise so when I cut the spouts I try and adjust that by cutting them a slight angle
so that as they dry they will straighten up. It's very annoying if you don't know your clay well to
cut everything dead square after the firing, you notice that the tip's at a funny angle,
people don't like it, they won't buy your pots if they look strange and also they don't work
well actually, they tend to dribble if that happens so that's a good tip.
Also putting handles on, especially on jugs, again there's torque within, from the bottom
of the pot to the top of the pot there's a slight twisting and you'll find a lot of jugs you look at
the handles have gone sideways slightly. The way to avoid this is to throw with soft hands,
throw gently and try not to put too much torque into the clay. If you throw quickly
on very dryish clay then you are going to put torque into the clay.
When the handle has been on the pot for usually an hour or so I open this section up here,
the bottom of the pot and that gives plenty of room for your fingers to fit. Again I put them
on a slight angle because I know my clay is going to twist and hopefully they'll true up.
When they're leather hard, which can take overnight in the winter or a couple of hours
in the summer, I cut the spouts at an angle and something I've always liked doing for years,
I don't know where I first saw it, is to roll a piece of square inch by inch wood down each
side of the facet, in other words in four places and that gives me a nice little frame
where again using the same wood I can give slight indents. Placed carefully in the right place I
think they enhance the pot. Your eye sits on them and also this ash glaze pools beautifully into
them. The other thing I've always loved doing is fluting. I have to be careful because having
been trained as an engineer I'm not trying to produce gear wheels here. I don't want it to be
too precise. I don't want a stiff elbow. It's just a question of just flowing with the form.
I once went to a fantastic demo by Takashi Yasuda and he said if you're not sure how to decorate a
pot ask out loud how do you want to be decorated. He said if there's no answer it doesn't want to
be decorated. Sometimes the pots do answer somewhere. Inside you get a message no I
need to decorate that pot. Others I don't. Or if you do decorate pots just only to enhance the form
not to hide it, not to smother it. Simple. I mean a potter is incredibly fortunate. What a
nice thing to do. You know we're very privileged to be able to just make things out of mud you
know it's amazing and actually be paid to do it. I don't look forward to ever retiring.
One day I'll fall off my wheel I know that but until then I'm going to carry on enjoying myself.
