I JUST BUILT MY DREAM AUDI RS6 GT3

Ex Used Car
15 followers
12 Video Views·May 17, 2025
My RS6 used to look like this.
But I've got to make it look like this.
To do so, I need wrap.
A body kit.
Alloys.
And a lot of hard work.
And I only have a week to do it.
Because next week, the RS6 will go on a shipping container
and be taken halfway across the world to Vegas
for one of the biggest car shows ever, SEMA.
So we better get moving.
In the last video, we lined up the body kit to the car.
But this time, we've got to fit it for real.
And what I noticed when I lined up the arch in the last video
is that it fit pretty flush all the way around
apart from near the front bumper
where there was a gap between the arch and the bumper.
And if any wind was to get in that gap at high speeds,
it wouldn't be good news for the body kit.
So I'm going to drill some holes in the front arch of the body kit
and then some more holes in the bumper to match.
That way, I should be able to get a nut and bolt
through the body kit and the bumper to pull it together.
On the back of the wing, I'm going to add a rivnut.
This way, I can screw a bolt directly into the wing.
And so far, that seems to have done the trick.
A lot better fitment at the minute.
Now, it's about to get crazy.
The actual front arch is held on pretty well apart from the top
which is what we're going to get to.
The thing is, the new wheel will come to about here
and sit nicely flush with the new arch.
The problem is, the original arch underneath here,
when the wheel sits in, if it goes up and down,
it's going to hit the original arch
which means we're going to have to start cutting.
So it's off again with the front arch.
I've marked a line with my pen on the wrap
on where I need to cut out and it's quite a lot.
There is no turning back now.
Some of you might be asking,
why didn't I do this before I wrapped the car?
Well, because I'm an idiot.
The front wing has well and truly sacrificed itself.
I'm just sanding down where I've cut now
to make sure there's no sharp edges
and then spraying a bit of etch primer on the bare metal
to prevent any corrosion.
And once that's done, I can refit the front arch.
Right, I was going to stick this on with adhesive and everything,
which is I think what you're supposed to do,
but I've managed to get nut and bolt all the way
through the inside of here and get to the other side
and that is solid.
I can almost pull the car off the ramp with it
and that means I can actually unbolt it
to take the bumpers off if I need to or anything like that.
We've still got a livery to go on,
but the nut and bolt job definitely seems to be
holding it nice and secure.
So, that's what the plan is for the rest of the kit, I think.
Onto the rear arch or should I do the front one?
Yeah, let's go to the rear.
Let's do the rear.
Before we do the rear arch,
I'm going to be fitting this part here,
which is actually part of the diffuser as well.
Going in.
Oh, no!
It's pretty good.
Just like the front arch,
I'm going to be adding rivnuts
because I won't be able to get to the nut
on the other side of the bolt on the rear bumper.
Now, my bolt can literally just thread into the rear bumper
and hold this bit of the kit in place.
I've kind of gone a bit overkill with the bolts
just to make sure that this body kit is staying on
when we're doing high speeds.
And with that part of the kit in place,
I can now line up the rear arch.
This bolts into that piece at the back
and also bolts into the side skirt.
But just like the front arch,
we need to make room for the new wheels
by cutting out part of the rear quarter.
I've already marked out where I need to cut.
Time to mask it up and just go all in on it.
Ready?
Yeah!
This felt so wrong.
But you've got to crack a few eggs to make omelettes, right?
Yes!
I don't know if you remember how big the disc was
when I first started.
Oh, my day!
Look at that! It's off-road!
Yeah!
Ready for America.
Right, I'm going to smooth the edges now.
And then, look, you can see this gap here.
You can see this gap here
between the outer skin and the inner skin.
Now, what normally people do
is just pinch it up and get it welded.
But obviously, we haven't got the time.
We haven't got a welder.
And that gap is literally only tiny.
So, I'm going to fill that with some Tiger Seal.
And that'll stop the water getting inside.
And everyone's going to say,
oh, that's wrong.
But it's still going to do the same job.
And as long as we etch primer it, it'll be fine.
I'm going to smooth the edges now.
You'll be pleased to know that I now have bought a welder.
So, potentially, I could go back and weld this piece up.
But as the gap's so small
between the outer panel and the inner panel,
I do actually think the Tiger Seal should hold up here.
But I'm prepared to get roasted in the comment section.
It's definitely sealed the gap.
With that done, I can now loosely bolt on the rear arch
and see how it fits
before moving on to the rear spoiler.
I see two bolts in the middle.
There must be ones on the corners.
What's on the new ones?
The rear spoiler is held in by two 10mm bolts
in the middle underneath this trim.
Yeah, see what I mean?
And then it simply just unclips on the roof.
Yeah!
Okay, so we've got to work out now
how we get the OEM brake light off that
and onto that.
And it was pretty easy.
There was only three Torx bolts holding the OEM brake light
onto the spoiler.
And we're just going to switch it over
onto the new carbon fiber spoiler
that we got with the body kit.
And then, hopefully, the new spoiler just slides into place
just like the OEM one did.
Let's see what it looks like
because I'm not taking it off after doing all that.
Wow.
It definitely sticks out further than the other one.
Fits quite good.
Yeah, the fitment's decent to be fair.
That is, yeah.
That is a wing and a half.
Wow.
Oh, yeah, that's...
It literally looks like this when I wear a hat backwards.
Oh, yeah.
So, should we start with the back?
Right now, the back of the car looks like this.
But we need to make it look like this.
To do so, we're using more wrap.
So before I carry on to fit the body kit for real,
I'm going to be fitting this livery to the car
and then fitting the body kit over the top of it.
The color is supposed to be like the Audi color
and it is...
On camera, it looks pretty much the same.
It does look the same, yeah.
It is a little bit off.
I don't know what it's going to look like
but it clashes so much with this
that we're only going to know
when we put the whole thing together.
I was a little unsure about the color
but I was hoping once I put the badges on,
it might change my mind.
I think it goes well against that.
It's meant to be salmon.
No, not salmon.
It's meant to be red.
I don't know. I like it.
Baz likes it but I still wasn't convinced.
Let's see what Hannah thinks.
It's like pink.
Yeah, it's pink.
Do you like it?
I like the pink.
Yeah, so Baz and Hannah like it.
I think I needed to add more of the livery
to see if I was convinced on it.
So me and Hannah started adding the stripe
which runs down the rear quarter
and the bumper of the car.
And in my opinion,
I think it's started to look a little bit better.
Oh, it's coming together now.
Yeah, yeah, yeah, yeah, yeah.
I can see it.
Yeah, yeah, yeah, yeah, yeah.
Yeah, it's coming together now.
I think we just have to get stuck in
and then just go for it and see how it looks.
Yeah, it's...
No, now I've seen that.
I think it looks alright.
With the kit, it's going to look mental.
Ah, it looks quite cool.
Yeah, it does.
Yeah, I think it looks good.
I think it's going to look good.
I think it's actually going to look good.
I'm excited now.
I'm excited.
Excited to see what the livery will look like complete,
myself and Hannah cracked on
with wrapping the rest of the car.
We're trying to stick with the Audi colours here,
black, red and a little bit of grey.
And because it's a kind of race livery,
it'll be wrong not to have a race number.
And that's what this little box is for here on the door.
But the sides of the car were the easy part.
Now it's time to move on to the hard part of the job.
Okay, sides are done-ish.
This bit's getting serious.
Glasses came on because the bonnet is the one thing
that you can see from both sides.
You can only look at one side at once, remember?
So, and I've only got one chance to get this right
because I've only got one bit of wrap.
This is not the time to mess up.
I'm using a bit of masking tape
and then a pen to mark the centre of the bonnet
or hood if you're American
and then run another bit of masking tape
along the centre of the bonnet.
I've got to get this bang in the centre
or else it'll really do my head in
when I'm looking at the car.
There is no room for error now.
Pressure makes diamonds.
Come on, Matt.
Oh, no.
I think I've just about got it in the centre.
So use the squeegee to put the stripe down
and then it's on to the two other stripes
which go on the car.
These ones are red.
Me and Matt measured them up and laid them down.
The headlights.
I know a lot of you wanted me to go for the LED Matrix ones.
We explain why it's expensive.
It takes longer to do.
So we're not going for that,
but I think we can improve the look of the stock headlights
and I have got...
So this is PPF, tinted PPF,
which will go directly on the headlight.
Yeah, like that.
That's it.
I've never PPF before,
but I'm going to give it a go
and it should make these look a bit meaner
because it takes the chrome look away from it.
Let's go.
Unlike wrap, PPF is applied when it's wet,
just like window tint.
I wet the surface and then squeegee out all the water
until it's dry beneath the PPF.
I use a little bit of heat just to stick the edges down
and I think we're looking good.
I think we've just got to wait for that to dry,
but look at the difference between the evil eye
and the non-evil eye.
That's a massive difference.
But I think we missed a trick.
I think we should have done them yellow.
I think we should have done yellow.
Now before we fit the body kit for good,
there is one last thing I think is killing the vibe off here
and that are these green brake calipers,
which go with absolutely nothing on the livery.
So I'm going to remove the brake caliper on the front
and remove the brake caliper on the rear,
which has the electronic handbrake attached to it as well
and start to change them into another colour.
The brake calipers are off
and as it looks like it's going to be a long night,
I've got my YFood at the ready.
I've got to strip the calipers completely down
and take off anything that I don't want paint going on,
like the brake pads and the electronic handbrake.
And once that's done,
I take a sip of my peach flavoured YFood.
YFood is actually a meal replacement drink.
It's not a diet drink.
It's not a protein shake.
It simply just replaces one of your meals
and tonight it looks like it's replacing my dinner.
So I'm going to be staying late to get these calipers painted,
but that's okay because they're full of goodness.
They're high in protein, they're lactose-free,
they're gluten-free and there's no added sugar.
Now you can't tell me you don't like YFood
because there are loads of different flavours to choose from.
Happy banana, cold brew coffee and so much more.
Whilst I was waiting for the brake calipers to dry,
I remembered I have to remove the rear diffuser.
Also inside these, there is 26 vitamins and minerals.
It's literally a win-win with this YFood
and to top it off, on goes the carbon diffuser
I got with the body kit.
It looks like the YFood has really kept me going tonight.
Yes, I actually painted the calipers red to start with,
but they went orange.
So I just resorted back to satin black.
Just like this YFood bottle,
which is actually a Matt Armstrong edition,
which could potentially be coming soon as well.
But if you want to grab a taster pack for YFood
and find your favourite flavour,
there is many you can do with the link
in the description box below
and with this banner appearing underneath me right now,
there's a discount code as well.
So thank me later and just wait for this.
Let's put these calipers together.
Thanks YFood for keeping me going for about three years now.
But now we're on the home straight with the RS6.
Just putting the brake pads back into the calipers
and then the calipers back onto the car.
Of course, we're now going to need to bleed the brakes
after this as well.
Although they weren't the colour I was going for,
I think they're going to match perfectly with the wheel colour
that we're getting later on in the video.
And now we'll let Fabian put the race number on the car.
Right, peel it off.
Is it straight?
Yeah, it's bang on mate.
Oh my days, a bit of a bubble.
He's absolutely just, oh my, oh my.
Matt, come over here.
Matt, come here.
Oh my God.
He's got acne.
Wow.
What happened?
What happened Fabian?
Now I've got to fit the rear arches for real,
which means out comes the Tiger seal
to seal this thing on once and for all.
Some people would use panel bond,
but the Tiger seal has a little bit of flex
which should allow a little bit of movement
when the car's on the road.
Hopefully it works.
But it's looking pretty good.
On top of the arch,
there's even more aero to go on as well.
I mean, I don't think you stand on it and make a big crunch,
but...
Don't stare.
That's good.
And...
Oh God, yeah, I didn't think.
Slam it for certified.
Yes.
Boom.
More aero.
It's all about you, isn't it?
No, no, no, no, no, no, no.
Like, this takes real...
No, no.
I'm pretty good, mate.
No, because if you get Tiger seal,
it goes over onto the red wrap,
and it's going to cause...
Hold that.
No, no.
Okay.
Very, very, very, very, very, very, very small bead on this.
Just in the middle, yeah?
Yes.
Small bead.
I don't want...
You're going to press it.
I don't want it to go onto the red wrap.
Like, genuine.
Keep going.
Keep that consistency.
Energy.
More energy.
Energy.
More energy.
Energy.
More energy.
Keep that consistency.
More passion.
More energy.
Don't get too carried away.
Whoa, I got carried.
Oh, no.
I got carried.
What is happening?
Okay, you're getting a bit too...
You can slow down when you trigger.
That'll be fine.
That'll be good.
Keep going.
Yeah, slow.
Slow. Stop.
Yes.
Oh, that was good for a beginner.
Do you want the...
We made a mistake.
Why?
We should have peeled the tape off first.
Right.
This has got to be a one bang.
That's all I do.
Am I doing this?
You sure you don't want to do it?
Well, I've got to put it on the tripod.
We've already...
We've marked out where we think this should go.
But this is a double wing.
Double.
Sensational.
How's it looking from underneath?
Certified, I think.
Yeah.
So, double wing.
And Chris is demonstrating what it actually looks like.
Which...
I think...
I think that is absolutely haphazard.
Oh my God.
Okay.
We're so close now.
We're so close.
That looks so mad.
Just when you thought this aero wasn't enough.
There's more.
Here we go.
Canard 1.
Canard 2.
Canard number 3.
Canard 4.
Canard number 5.
And that's not even the last of it.
There's two more to go on the door just here.
But we can't really fit them just yet.
Because if we...
Still don't have a door handle on here.
But if we open the door...
Where the canards go is just here.
So, if I fit them wrong, it's going to hit into that.
So, I need to be able to open the door fully to do that.
So, we need to get this off the ramp.
And we've never driven this car properly yet.
So, it's probably best we service it first.
Open that.
The car's only done 36,000 miles.
So, we're only going to be changing the oil and filter today.
Let's see if I've got the technique.
Not getting around that.
Boom!
No! I've failed!
But even though the mileage is low, the oil is filthy.
It's completely black.
So, it definitely needed changing.
Where's the oil filter?
Right there.
Oh!
That's why we like Audi's.
They ease it.
Old one.
New one.
In.
Up goes the new oil filter.
And that gets tightened.
And then back in goes the sump plug.
And that gets tightened.
After that, I've got all the under trays to put back on.
And this actually helps secure that front splitter a little bit better.
Oh, that splitter is solid now.
Right, oil.
Now, we're done underneath the car.
It's time to lower it down and add eight and a half litres of oil into the engine.
The only way to check that is to get in the car and start it.
Right.
I think, to check the oil, we start it.
Oil level.
Engine must be warm.
So, we wait for two minutes.
And if the engine is low, you run the car for two minutes with low oil.
Not good.
We wait.
We'll wait then.
Is it warm?
Oil level displayed after approximately two minutes.
Has it been two minutes?
You'll have to turn it off though now.
Oil level displayed approximately after two minutes.
Engine must be warm and must be switched off.
Whilst we were waiting, Matt suggested that the RS6 needed more carbon.
Hey, you're absolutely right, Matt.
You know what we should do whilst we're waiting?
Get these black mirrors off.
Yeah, man.
I think you're absolutely right.
We need more carbon fibre.
Oh, look.
Bang on.
They call me the master mechanic.
You literally Googled it, mate.
So, the oil level is looking good.
It's time to get rid of the black mirror caps.
And we're going to replace them with carbon mirror caps.
And this will tie in nicely with the rest of the carbon body kit.
The mirrors are pretty easy to remove.
And once the carbon ones are fitted, they were perfect.
One other thing I wanted to do was change the chrome Audi badge on the front of the car to a gloss black one.
And also change the chrome RS6 badge to a black one as well.
And add black RS6 badges to the rear.
It's the little touches.
Unfortunately, we've got to put the stock wheels back on.
But we're going to need some bigger wheels, which is the next mod.
But we have to drive there.
These wheels are going to sit so far inside the arch, it's going to look like a clown car.
The front wheel went on pretty easy.
But the back wheels were a different story.
Will this fit in the rear of the car?
It doesn't fit.
Does the wheel not fit?
It literally doesn't...
No, it doesn't.
It doesn't fit.
What?
Oh my...
No, it doesn't fit.
We then found a strange technique on how to make these 22-inch alloys fit.
We won't be doing any F1 pit stops anytime soon.
That is well odd.
That's going to be a problem, that is.
Look from here.
The tyre is just well behind there.
We've gone 60mm wider.
That's a 50mm gap, and we've gone 60mm wider.
I don't think the new wheels are going to work.
Let's see what happens.
Oh, there's a bit more room.
There is a bit more room.
But is the 60mm working room?
It's going to be very close.
How's the kit looking?
That looks savage.
My dream RS6 was almost ready.
Just a few more little bits to add on,
and then we're going to pick the wheels up,
which should finish off the build cosmetically anyway.
This is it.
I think it's pretty much almost done.
There's a few last little things,
but the main thing now are the wheels.
And this is going to be the first time driving the RS6
after I've ruined it with this body kit.
Step one, don't break it on the way to wheel mania.
Step two, watch the splitter.
And step three, don't break down.
I hope this drive's okay.
The RS6 for the first time.
Loves it, mate.
I'm expecting to hear a lot of stones,
you know, like, cos stones are just going to pick up in the kit.
Especially with the new wheels, cos they're...
Oh, yeah.
Seem all good so far.
We made it about 50 metres.
But as we pulled out from the unit,
things went downhill fast.
Oh, it sounds quite cool, doesn't it?
Sounds quite cool, yeah.
What's wrong?
We're in limp mode.
No, why?
Engine management light already.
It's flashing as well, we're in limp.
I've got no power.
We've only gone 100 metres.
Wow, we literally made it down the...
Do you reckon it's cos we've got no fuel?
Maybe, yeah.
Oh, we've got EPC light on now.
TPMS.
How do I...
Oh, it's shaking.
We're missing.
I think it might be cos of no fuel.
How do I change it?
It's in, like, sport mode.
Get it out of sport.
Put it in comfort.
Oh, we're really struggling.
Oh, no.
What? As if we just pulled out and it's, like, dead already.
We should have brought the code reader.
We're going to break down.
We're done.
What do you mean we're done?
We're done, I've got nothing.
No.
Everyone's going to think that's fixed.
We're done.
We're going to have to put...
I think we've run...
Low battery.
People are going to think that's fixed.
We literally just made it down the road.
That's a hit.
What do we do?
I can't walk back.
I'm not happy.
I think it's run out of fuel.
So we've got to go get fuel in the Aston
and then bring it back here, put fuel in and see if it works.
And if not, we've got a problem.
The only logical explanation to why we broke down is, well, no fuel.
And there's a simple answer to that.
Go get some.
Come on, then.
We're back.
After we got fuel, we found out how fast this car actually was.
Before finally arriving at the place we set off to go to.
Wheel Mania.
And we made it to Wheel Mania in one piece.
And everything still seems to be on the car, which is good.
And obviously we came here for wheels,
which actually could literally make or break this car.
Because just check this out.
This is where we were struggling last time.
So you'll see what wheels we've gone for.
I've not seen them yet, but we've done a special design for them.
We want to make this special.
But Wheel Mania have had literally zero time to make these as well.
So if these work, it's going to be amazing.
But to get it past this gap here, it is insane.
There's not much gap to get it on.
I don't know how they're going to do it.
But let's go take a look at them.
Here we go.
I'm a bit nervous.
I'm just hoping they fit.
Yeah, I know.
Yeah, they might look good.
Might not fit.
Oh my God.
What?
They look mad.
They're the perfect colour as well.
Perfect colour.
I was scared they were going to be like too gold.
But no, they look mint.
That looks sick.
Oh, I hope they're going to fit.
Oh, and also we went a size smaller.
Then there's 22 inches on at the minute.
And these are 21s.
I think they are 21 inch.
And check this out.
MA in the wheel and MA in the center cap.
This is literally a build for myself.
So I've been selfish and just put MA logos in it.
Right, let's get them on the car.
Hopefully, hopefully.
We've now all seen the wheels that Wheel Mania had specially made for this build.
And they look incredible.
I just hope they're going to fit.
But it wasn't fitting the wheels that was the problem.
It was getting the old ones off.
Oh, that's tight.
With the old ones off, will the new ones go in place?
Oh, I knew we should have gone down a side.
I knew it. I knew it. I knew it. I knew it.
Bang on.
Wheels, perfect fitment.
But we didn't have the all clear just yet.
The wheel was catching on the front of the body kit.
Moment of truth. Let's find out.
You can just see the tyre catching on the side skirt there.
If the car sits lower when we start it, we think we might have the clearance.
I feel like that's got to go lower in it.
Yeah, do you reckon that's going to work?
Should we try it?
I really hope this works because these wheels look insane.
I just want them to fit so bad.
Come on. Perfect. Look at that.
Look at that. Oh my days.
That is perfect fitment.
Bang on. That is perfect fitment.
Perfect fitment. I'm buzzing.
Let's get the rest of them on. That is so sick.
Oh my days. I thought it wasn't going to be our day today when we broke down.
But so far, we're going well. Still got the fronts to do.
What a result that was.
And it was the same story for the other side.
And even on the front, we had a similar story.
They were just catching when we had it in the air.
But when we lowered it down, perfect fitment.
The wheels are on and they are spot on.
Absolutely spot on.
If you need wheels, you need wheels refurbishment, anything to do with wheels,
Wheel Mania are your guys.
The link's in the description box below.
And of course, they have sponsored the build.
Now, you guys need to see these wheels on the car because it looks insane.
Absolutely unreal.
What a way to almost finish the build.
There's still a few more bits left to do, which you'll see in the next video.
But out of 10, it's a 10. It's got to be.
Eh, Kevin? It's a 10.
Thanks so much for watching this video.
If you enjoyed it, hit that subscribe button, hit that thumbs up button.
And I'll see you in the next video. Peace out.
Oh, whoa, whoa, whoa, whoa, whoa, whoa. Stop, stop, stop.
