🇩🇪 Supersonic Reverse FMA: ATA, Cams, Vorbereitung, Details & Pflege #care #preparation #maintenance

Defending with Past Crossbows
3 followers
🇩🇪 Supersonic Reverse FMA: ATA, Cams, Vorbereitung, Details & Pflege #care #preparation #maintenance
Comments are disabled for this video.
Moin. Hallo. Video in German.
Supersonic Reverse by FMA.
I would like to test different rockets at speed.
And for that I have to prepare these dusty, you could say something else,
uhm, Supersonic Reverse.
I will tell you a few details about them.
Uhm, yes, I have one and a half years of experience with this game
and with the other games of Giant King, or better said FMA,
so all Sonic Stories, Drayton.
If you are interested in what to look out for before the first turn, stay tuned.
Otherwise, see you next time. Let's go.
Yes, this is not a classic unbox video or something like that.
It is already set up, but it is still completely new.
Here is an Anna von Tüftlern, a B-Pod from Fat T-Fan,
from, from, well, not a bad thing.
Here is a T-Fan number on it.
Not the supplied Red Dot.
This is an NCS-Star.
Red Dot based on the US market.
3-9x magnification.
Everything from the last two years.
Not spectacular, but it works.
Yes, and here is a T-Star on it, from Fat T-Fan.
Yes, classic and such, right?
Good. Okay.
Yes, I have set it up according to the instructions.
It is on 1, I don't need more.
So.
I will smoothen it out.
Yes.
Before we do that, we do something else.
We go through everything once and then we continue.
Yes.
Exactly.
And what you do with it, I will show you now.
Yes, ehm.
So, you can see it better.
When I assembled it, there were here on this side, the other side,
there were two screws, you had to fix them.
Here.
To fix the throw arm.
In any case.
And of course the last screw.
Here are screws.
Exactly.
I also had to attach the titanium.
Well, also two screws.
It is very, very important.
These screws from Junk Sink are really wide.
That means you really have to be careful when you assemble it,
that you turn it in straight and don't get it crooked.
You don't do that anyway, but with this arm bus it is really, really important.
In addition, it is important to check all screws regularly,
because they loosen very easily and very easily.
So.
So again, I turned it a little loose before so that I could turn it again.
So.
Yes.
Now there are different screws from the riser, i.e. from the head, from the throw arm.
I'll take a look at them again.
How tight they are.
Yes, that's the right one.
Okay.
Yes, exactly.
In this case it was already mounted.
With the Drayton, the throw arm is not yet mounted.
Or I think with any other of the various variants.
Okay, they are tight.
This one here is the connection.
Connection.
At the moment.
So.
You can see it better.
So check these three and this one.
I turned it in here.
I'll check it again.
A little more on it.
Oops.
Yes.
And then here's the rail, but that's not so ...
Yes.
And then I look at all the screws of all the cams.
All.
Except for two.
A little bigger.
Yes.
So all cams.
Once through.
The screwing.
Yes.
A little bigger.
I'll show it like this.
So here the cams.
Also check once.
Check if they are tight.
The steering cams, so to speak.
Okay.
Good.
That looks good.
Okay.
The next thing I do.
That might sound a little weird.
But I go all once.
Carefully touching up.
And feel whether around the cams.
Somewhere sharp-edged scratches are.
Yes.
Even if they are in the tensioning process.
Not directly affect.
Or not necessarily directly affect.
It can still cause problems.
As I said, it's still very, very dry.
Here in front.
These are the screws for the fishing reel.
Or the front mount tube.
I don't use it either.
I don't use it at all.
Good.
So.
Next.
I measure.
Namely the ATA value.
Axle to axle.
That means.
This point here.
To this point here.
I intermeasure.
I do the same again.
In the tensioned state.
I mark here.
To the same point.
Here in front on the cam.
To see how far.
The reel.
In the sequence.
Yes.
Tensioned and un-tensioned.
And the values.
I just note.
22.5 cm.
I write that down.
Good.
Before I tension here now.
I will of course.
The first.
Baby.
F8.
They look good too.
You can of course.
Also check here again.
From the cast arm.
Yes.
I do that too.
Everything looks good.
Good.
Next.
I look at the lines.
The lines.
To the angle.
The line.
Is the angle.
The cams.
The angle of the cams.
To the rail.
And the cams.
To each other.
That means.
They tip.
Usually at the end.
When the material.
Changes.
And now here.
Very special.
At the beginning.
They are.
From the front.
Straight.
Yes.
And that are.
Loops.
Yes.
There are a lot.
Necessities.
To do that.
Many ways.
Upwards.
I have been.
So far.
I have been.
I am always in exchange.
With different people.
Who are even more.
Occupied than me.
I do.
Okay, let's start with wax.
For this I have a different kind of wax.
It's a small amount of wax.
I just pour it in here.
It's important that I rub it in,
because through the heat,
which is generated by the friction,
the wax is better absorbed by the material.
Sorry about the camera.
And really all movable parts.
Because there's a lot more.
I'll show you another example.
Why do I prefer wax here?
I just use a very narrow razor.
I put it on the rail.
Then I press it on the rail.
So I get a high wear resistance.
Okay.
Cotton smear spray.
That's what I use.
And I'm good with it.
As I said, there are a lot of ways to get around.
This is the cam I made.
All mechanical parts.
It smells a bit like in a two-wheel shop.
Like in the other video.
Good.
Now I have a rail here.
And I'm not done yet.
First I put a bit of wax on it.
It doesn't pull as much dirt
as my factory-used
industrial fat.
That's why I do it differently.
I don't do that anymore.
I use a compound system.
I put it everywhere.
I put it in all parts.
Where I can reach.
Okay.
And now the rail.
And as I said,
in this case,
I don't use wax.
Okay.
Here again.
This to the back.
I put it on the wax.
Here is the black.
I put it in.
Yo.
That looks good.
What else do I have?
You think I'm crazy.
But as I said,
I spent a lot of time
with the different models.
And they need a lot of wax.
So.
Okay.
and if the test was successful
the components worked
Let's do a power measurement
in my brutal new camera
with a new power piece
you already know it
This is a membrane filler box pin from JustinTuner.com
I have it here
wait a second
I just screwed it on
I showed it in my short video
today or yesterday
yesterday I think
yeah, we will just throw it away
just like that, just for fun
at the final
first shot with this new
Supersonic Reverse
from FMA
that's exciting
yeah, it spins normally
as I know it
that means
it will
have similar values
looks heavy
let's save
and
my DIY
Target Ball
has survived well
and is easy to remove
okay
one thing I forgot
I forgot to
mark
the dots
on the cam
you do it
like this
and on the other side
and the same
again
why don't I do it now
and show it
I only have this big
adding in white
and yeah
I will show it
in the next video
thanks for watching
and if you liked it
stay tuned
