How to Make Electric cycle at Home | Make your cycle electric bike

Two-Wheeler Technology
5 followers
Apr 25, 2025
How to Make Electric cycle at Home | Make your cycle electric bike
So, we have a ranger cycle with disc brakes in both the wheels.
Now, first of all, we have to turn this cycle from here.
After turning the cycle, we have to take the slide wrench here.
And from the slide wrench, we have to loosen both the nuts of the back wheel.
Friends, first of all, after loosening the nut of the back wheel, we have to remove this wheel from here.
The first process is to remove the back wheel of any normal cycle to make it electric.
So, here we will first remove the chain.
And after that, we will remove the chain from the free wheel.
And we will remove this back wheel very easily from the cycle and keep it here.
Now, let's see what's in this box.
To make any normal cycle electric, we use an electric cycle kit.
So, we have an electric cycle kit.
As you can see, this is a controller.
Intelligent Brushless Motor Controller is written here.
We will use this controller to make this cycle electric.
Along with this, we are going to show you all the parts one by one in this box.
So, here we have a motor.
Friends, this is a hub motor of 350 watts.
It operates at 36 volts.
So, we will use this motor to make this cycle electric.
Here you can see, this is a hub motor.
So, how is it used?
You will get to see the whole process later.
Keep watching the video.
Here we get some nuts and bolts to fix this motor.
Here we get some nuts.
And along with this, we get an accelerator.
Friends, this is a throttle.
It has a display and a key.
With this, the whole cycle system is turned on and off.
After that, we have a left-hand grip.
Here we get to see a light in this kit.
So, we get to see a very good LED light.
Along with this, we get to see a horn and a light switch in this kit.
After that, we have a brake cut-off switch here.
So, here we get a brake with a motor cut-off switch.
Along with this, we get a pedal assist.
So, we get to see the whole kit inside this box.
Using all these kits, you can make any cycle electric.
Friends, we are going to use a controller box which is not available in this kit.
We have to purchase it separately.
So, we have purchased a controller box separately.
You will not get to see a controller box in any kit.
After this, we are going to use a 36V 12A lithium-ion battery pack.
This is along with a halon case.
Along with this, you will not get to see a battery box and a controller box in this kit.
So, friends, we have removed the wheel.
Now, we have to put the motor in this wheel.
So, we will put this motor inside this wheel.
As you can see, friends, we have already fixed the motor in the other wheel.
So, to fix this motor, you will have to take this motor to a cycle mechanic.
And you will have to take the wheel of your cycle.
He will fix the motor in the rim of the cycle very easily.
After that, you can convert it yourself.
Like I am showing you here.
So, now we are putting the back wheel with the motor.
After that, we will put the nut inside the wire.
And we will tighten this nut from here.
So, slowly, we have to tighten the nut on both sides.
We don't have to tighten it all at once.
So, we will take the slide wrench here again.
And we will tighten the nut on both sides.
After tightening, you have to see if the wheel arrangement is correct or not.
You have to rotate the wheel once and see.
So, ours is perfect.
Now, let's straighten this cycle again.
So, our main task was to assemble the motor.
We have done it very easily here.
You can also do something like this.
Now, next, we will remove the right-hand grip of the cycle from here.
And after that, we will also remove the left-hand grip from here.
After that, we have to remove the brake here.
Which was a normal brake in the first cycle.
We don't have any work of this brake.
We will throw it away.
Or you can give it to the cycle mechanic.
Or you can keep it for later use in another cycle.
So, we have got this with the kit.
This is our brake.
In which the cut-off sensor is given.
With which the power is cut in the motor by taking the brake.
So, we will put this brake here on both sides.
We have to tighten it from the right and left with the allen key.
So, we have tightened it on both sides like this.
After this, we have the switch of horn and light.
We will put the switch of horn and light on the left side.
We will also tighten it with the allen key.
So, after tightening it in this way, we will put the grip here again.
We got to see the grip in our kit.
We will put that grip here.
After that, we will put the throttle here.
The nut of the throttle has to be loosened a little from here.
To put it in the handle here.
After that, we will put the throttle in the handle very easily.
We will tighten the nut again.
With which it will be tight.
So, you can see that we have also put the throttle here.
Now see here, our throttle rotates.
It works just like a scooter.
So, we will extend the wire from here.
We have to extend all the wires.
Here is the wire of the switch.
Here we get to see the wire of two brakes.
We will take all these wires down.
Because we have to put all these wires down.
Here we will put the controller box.
To put the controller box, we get the clamp with it.
The clamp has to be tightened in the controller box.
After tightening it well, we will put the controller in the controller box and tighten it here.
So, see here, the controller box will be put here in this way.
We will put the controller in this.
Friends, now we will show you the connections here.
So, let's see how the throttle, brake and motor are connected with this controller.
Friends, here you will get written in all the wires of the controller.
Which wire will be connected in which accessories.
So, here we first connect the throttle.
You can see this wire of blue color.
Here you have to match the color of the wire.
So, this wire is of our throttle.
So, we have connected it in the throttle.
And this is the wire of the key.
You also got to see the key with the throttle.
This is the wire of the key.
Here you will also get to see the written wire of the key.
Now we will open it from here.
And this wire is of our light.
Here is the wire of the horn that we showed you the switching.
For the horn, you have to connect it in both of them.
And after this, we have the light.
So, for the light, you will get to see a connector here.
All the connectors are here.
Every connector connects to each other very easily.
So, this is our light.
And we will take this connector of the light from here.
And we will put this connector here.
This is for the switch that comes with the horn of the light.
So, we will connect it here.
This is the connection of our light.
Now here we have the next.
These two wires that you are getting to see are of white color.
In white and black, you are getting to see two plugs.
These two plugs are of our brake cut-off switch.
So, here for these two brakes, you will get to see these two plugs.
In both, we have to connect the wire of the brake cut-off switch.
After this, we are not using much here.
So, here we have a wire of the pedal assist.
PSA is written on the wire.
This is our pedal assist.
So, we will connect this pedal assist from here.
So, our connection of accessories is complete.
Now we have this.
There are five wires in the hall sensor of our motor.
So, we have to connect this hall sensor from those wires.
These two wires are of the battery.
Red and black.
And these three wires are the phase wires of the motor.
So, here we have to match the color of the wire.
Now, first of all, we will fix the light on the front side of the cycle.
So, here we have to open this nut.
The nut of the front wheel.
We will open it here.
And after that, we will fix the light here.
After fixing the light, we have removed the plastic.
So, friends, we get to see a lot of wires near the handle.
And it does not look very good.
So, for this, we have a wire cover here.
This is a wire cover of plastic.
So, this is a spiral type wire cover.
With this, all our wires are together.
And it looks very good.
We do not get to see a lot of wires together.
So, it looks very good.
After this, we will install the pedal assist.
To install the pedal assist, we have to open the pedal from here.
We will take the ratchet here and open the nut of the pedal from here.
After this, we will put the pedal down.
After this, we have to open it here.
Friends, to open it here, we have to turn it in reverse.
If we turn it on the right side, it will open.
If we turn it on the left side, it will be tight.
So, here we will take this magnet of our pedal assist.
We will put this wire sensor here.
And after this, we have to put it in it again and tighten it again.
If we do it on the left side, it will be tight.
So, we will tighten it well here.
So, we have tightened the nut here.
Now we will take the magnet of the pedal assist here.
We have to put the magnet in it from here.
It goes inside very easily.
After putting it in, we have to tighten it well here.
Because we will also put the pedal on it.
So, there should be no touch here.
There should be a little gap.
There should be no touch in each other.
There should be no friction.
After this, we will put the pedal here.
And again, like before, we will put the nut here and tighten it well.
After putting it on you, it is also necessary to check the alignment of the pedal.
After checking the alignment of the pedal, tighten the nut here.
Your pedal assist is installed here.
So, we will also put its cover here.
So, friends, I have shown you all the connections before.
And from here, you can see that we have connected the motor wire.
This is for the battery.
We have removed two wires from here.
And we have fixed the controller inside this box.
So, now we have this Helium case.
This Helium case is a battery box.
So, we have to remove this base plate from this battery box.
You can see here in the back side of this base plate.
And we have to put this base plate on this pipe in the center of the cycle.
So, here is a hole.
We have measured from the hole in the pipe.
And from here, we will drill in the pipe.
We will do one drill here.
And one drill is already inside the cycle.
