The futuristic XB-70A was originally conceived in the 1950s as a high-altitude, nuclear strike bomber that could fly at Mach 3 (three times the speed of sound) -- any potential enemy would have been unable to defend against such a bomber.
By the early 1960s, however, new Surface-to-Air Missiles (SAMs) threatened the survivability of high-speed, high-altitude bombers. Less costly, nuclear-armed ICBMs (Intercontinental Ballistic Missiles) were also entering service. As a result, in 1961, the expensive B-70 bomber program was canceled before any Valkyries had been completed or flown.
Even so, the USAF bought two XB-70As to test aerodynamics, propulsion and other characteristics of large supersonic aircraft. The first XB-70A, on display here, flew in September 1964, and it achieved Mach 3 flight in October 1965. The second Valkyrie first flew in July 1965, but in June 1966, it was destroyed following an accidental mid-air collision. The third Valkyrie was not completed.
The first XB-70A airplane continued to fly and generate valuable test data in the research program until it came to the museum in 1969
Hi, welcome to the National Museum of the United States Air Force.
I'm Dr. Doug Lantry from the Museum's Research Division,
and we're standing here beneath the massive and legendary
XB-70 Valkyrie. The purpose of the XB-70 program was to
enhance nuclear deterrence. It was meant to be a high speed,
high altitude, nuclear bomb delivering aircraft.
And that was its role in the early part of the Cold War.
It was an early part of the so-called triad.
Bombers, submarines, land-based ballistic missiles.
Let's talk about the canards on the XB-70. They're a really unique design
feature, and this airplane has unique geometry. The canards contribute
to that geometry by solving a really important problem.
They're a trim device that solves stability problems between the low
speed of about 150 knots and the high speed of about Mach 3,
and every speed in between. You'll see that the back half of the canard
is a flap. Having a canard on the fore part of the airplane
solves the problem of putting flaps on an extreme
delta wing design. So what about the windshield on this airplane?
Well, it's got unique features as well. For supersonic flight, a completely flat
profile is necessary. So the outer windscreen on the XB-70
is a kind of ramp that transitions up and down.
At slow speeds, it can transition down into the nose to give the pilots a
forward view. But at high speed, that outer windscreen
comes back up and covers the inner windscreen.
So the crew compartment is completely isolated from that, and the outer
windscreen is only for aerodynamic purposes. Let's
talk about wheels. This is the front gear of the XB-70.
These tires are made by BF Goodrich, and you'll notice that they're silver. Not
many tires are silver. BF Goodrich developed a special heat
resisting compound that's infused throughout the body of the tire
and also painted on its surface to make these tires withstand temperatures
up to 360 degrees Fahrenheit. It's made possible by that silver
painted compound on them, which is also infused throughout the body of the tire.
The tires, in turn, are cooled up in the wheel well
by a mixture of ethylene glycol circulating through brazed
tubes inside the wheel well. So they're cooled by the surface
of the tire, and they're cooled inside the aircraft.
So here's the rear bogies of the XB-70, where the main
tires are. The tires are the same as on the front,
but check out this little tire here. This little one
is about anti-skidding. That tire doesn't have any temperature protection because
it doesn't need it. What it does is it tells the computers
inside the airplane when to apply the brakes and how much.
The brakes, by the way, on this airplane withstand up to about
2,000 degrees Fahrenheit temperatures. There was an incident once landing one
of these airplanes where these bogies didn't work like they
were supposed to. The whole thing pivots front to back
so that the back tires hit first and then the front tires. Well, one time
one of the bogies didn't pivot right, and so the back half of one of the bogies was
severely damaged. Didn't lose the aircraft though.
Compression lift is a key feature of XB-70 aerodynamics.
The area of the shock wave formation on this airplane, which is
just at the front of the intake splitter duct on the underside of the fuselage
and wings, creates a shock wave that
increases lift in this airplane by as much as 30 percent.
It also creates a reduced drag condition
and enables the airplane to cruise quickly at mach numbers at a lower angle
of attack. Saves fuel, increases speed, decreases
drag. So compression lift is a key component
of the aerodynamics of this airplane. Another key part of XB-70 aerodynamics
is variable geometry wingtips. These things over here.
At low speeds, landing, taking off, and so on,
the wings are perfectly flat. Perfectly flat. No anhedral, no dihedral.
But at low altitude, low supersonic speeds, those wingtips can fold down
at 25 degrees. That increases the stability of the airplane.
Makes it easier to control. At high speed, high altitude,
those wingtips fold down to 65 degrees. Not only does that solve
stability problems, but miraculously, it also increases lift.
So the variable geometry of this airplane
both increases lift, provides stability, and allows an airplane like this to
operate in a wide range of speeds between 150
knots and about mach 3. It's really an amazing
design feature. Another thing about the fold down
wingtips is that at high supersonic speeds,
because they provide extra stability, they allow
the relative size of the twin upper fins, the vertical fins,
to be that much smaller, thereby reducing drag. This is all very clever design
solutions to high-speed supersonic flight in the
1960s. Riding your own shock wave is a feature
of this airplane. That compression lift holds the airplane up, of course,
provides like 30 percent greater lift than it otherwise would if the shock
wave didn't exist. And also the fold down wingtips increase
that lift in addition to providing stability.
They allow the vertical fins on the top of the airplane to be that much smaller
proportionally, which in turn reduces drag. So it's all
part of a very clever design solution that all works
together through some variable geometry to make
this airplane a unique aerodynamic specimen.
One of the most amazing features of the XB-70 that you can see here in the
museum is the business end of the raw
power of this jet. At the back of the aircraft
you can stand here and marvel at the six,
six side-by-side General Electric YJ-93 after-burning turbojets.
Now the aircraft could achieve Mach 3 even if one of the engines wasn't
working with only about a seven percent loss in range. But the bottom line for
these engines is that they operate best at very high
speeds. They operate in continuous afterburner and so
they're most efficient at super high speeds.
And joining six of them together in a row like this
is nothing but high speed power. Each one of these engines develops a
maximum of about 30,000 pounds thrust.
Each of those engines actually was developed as
well a single engine for another single engine
fighter project which was canceled. But putting six of them together,
same engine, gives this airplane its tremendous
speed. You can see modern examples of something like this. For example,
today's B-1B has four of the same approximate types of engines
that the single engine F-16 fighter has. So think of a B-1
in terms of power as about four F-16s. Same with this thing, it's got six
fighters worth of power. This is the guts of the XB-70's power.
This is General Electric's YJ-93 afterburning turbojet.
This engine weighs a little more than two tons
and develops a maximum of about 30,000 pounds thrust.
It's got an 11-stage air-cooled compressor and a two-stage
turbine. One of the unique things about this engine, unique for the time anyway,
is that the afterburner, though it looks like any afterburner,
is not controlled through cable linkages. This afterburner
is controlled electronically because you've got six of them to control.
That's a big task for any pilot. And so think of six of these two-ton
engines together, each developing 30,000 pounds of thrust,
and you get a really, really fast, big airplane like the XB-70.
An interesting part of the trailing edge of the XB-70's wings
is the series of elevons, combination ailerons and elevator along
the trailing edge of both wings. These are for latitudinal and longitudinal
stability, and it was designed with these trailing edge
elevons to be split into six segments on either side of the engine bay.
And they're operated by no fewer than 24 separate hydraulic jacks.
By the way, the elevons are operated only hydraulically.
There's no manual reversion for the pilot if the hydraulics fail.
But again, they operate as elevator and aileron both.
Flaring to land, you're looking at the sky.
So, no wonder these guys were the hottest pilots around.
When you try and fly this crazy shape, it's elegant, it's sleek, it's great,
but it's got to be really difficult to steer.
In addition to the airplane being tricky and exotic to fly,
think about maneuvering the XB-70 on the ground.
Think about where the pilot is and where the front gear is.
The pilot is something like 60 feet in front of the gear.
So, trying to turn the XB-70 is like, I don't know,
trying to turn a diving board that you're sitting on the end of.
It's got to be very tricky because the wheel's back there
and you are out here in front turning.
So, you're just swinging across this arc with the wheels way behind you.
That had to be hard to do.
It was a complex airplane.
Like other airplanes of its era, it was full of analog dials and gauges.
And so, every pilot knows that there's a kind of a habit,
a system of scanning the instruments to make sure that everything's okay.
Well, think of that job inside the XB-70.
Six engines.
A flight regime anywhere from 150 knots to Mach 3
with high-speed crews at Mach 2 or Mach 3,
preferable for the airframe and the engines.
Plus, you've got a control system that is dependent on these forward canards,
elevons in the back, folding wingtips and so on.
So, this is not your average airplane to fly.
It was perhaps a little tricky and unusual.
However, the seven people who flew that aircraft were well-acquainted
with unusual flying situations in unusual vehicles.
So, it wasn't a big surprise for them, but it would probably overwhelm the rest of us.
The crew accommodations in the XB-70 might not be what you'd expect.
You might think, wow, in such a fast, high-altitude airplane,
they're going to be wearing spacesuits.
Well, not so.
The XB-70's crew cabin was air-conditioned in a shirt-sleeves environment.
The temperature in there at any speed was something between 70 and 100 degrees Fahrenheit.
So, it was a shirt-sleeves environment.
However, if they experienced decompression at high altitude,
each of the crew members, the pilot and co-pilot,
they each had a separate kind of clamshell enclosure,
very similar to the one in the B-58, that would automatically close.
And then, from inside of that pressurized enclosure,
the pilots could monitor the instruments through windows in this little clamshell,
and they could bring the aircraft back down to a safe altitude.
They had controls inside the little clamshell.
Once they were at a safe altitude, they could open the clamshell back again.
Now, if they had to eject from the airplane, the whole clamshell,
both of them would come out of the airplane, out of the top, like an ejection seat.
One of the most interesting technological facets of the XB-70 program
was its steel honeycomb structure.
Advances in the art of steelmaking realized in the XB-70 program were especially notable.
It was principally a steel airplane.
It represented the first widespread use of stainless steel in a honeycomb panel structure.
The panels of the airplane, which are comprised of
facing sheets of steel brazed onto a honeycomb-like core,
make up 22,000 square feet of the surface of the airplane.
This kind of honeycomb-style stainless steel
was carried out by the Armco Steel Corporation of Middletown, Ohio.
We've got a honeycomb panel on display that you can see that was made by Aronca Incorporated.
But these honeycomb steel panels are an important part of XB-70 technology
and an important legacy to the art of steelmaking and aerodynamic structures.
Sixty-nine percent of the airplane's 150,000 pound weight
is this welded stainless steel honeycomb sandwich.
It covers the wings from tip to tip.
It covers the engine box and the center fuselage and the fins and the rudders
and the forward part of the canards.
Most of the forward fuselage and aft plane is built up from titanium alloys.
So here's an airplane that's mostly stainless steel but also titanium.
These things also make it very, very unusual in the 1960s and make it exotic even today.
The second XB-70 was a tragic loss.
In the summer of 1966, it was flying a photo mission.
It was being photographed with two chase aircraft.
One of them was an F-104, but the F-104 collided with the XB-70 in midair,
and its pilot was killed immediately.
And the XB-70, its wing was damaged and both vertical stabilizers were gone,
and it flew on for only a couple of seconds before it became uncontrollable.
And its co-pilot, Major Carl Cross, died, unfortunately.
And the North American pilot, Al White, ejected from the XB-70, but he was badly injured.
But that's how the airplane was lost.
That's why there's only one XB-70 now.
The base support for the XB-70 was all at Edwards Air Force Base in California.
Big Air Force testing center.
They had all the facilities, super long runways, all the rest of it.
And the only time that an XB-70 ever landed anywhere else
was when our XB-70 landed here at Wright Field.
The museum got its XB-70, which was the first one made,
and the only one that exists now, in 1969.
The talents required to design the XB-70 included both talent and persistence.
The airplane was designed without the kind of supercomputer modeling that we're used to having
today, where we know exactly how aerodynamic flow works because we can simulate it inside
of a computer at millions and millions of operations per second.
Well, in the 1950s, airplanes were designed with a decent knowledge of how aerodynamic flow works,
but testing the real article was the proof of how it was actually going to work.
So all of the crazy geometry of the XB-70, the forward canards, the elevons,
the slightly smaller-than-you'd-expect vertical surfaces, the hugely swept wings,
the wingtips that fold downward in high-speed flight,
all of that variable geometry is the result of people thinking through high-speed aerodynamic
problems and then also thinking through the requirement for the airplane to take off and
land at a relatively low speed.
So you've got the windscreen, the canopy that pivots so that at high speed it's a flat surface,
but at low speed the pilots can still see out.
You've got the canards acting as flaps.
You've got the splitters in front of the engine creating a place where a compression lift comes
into play, massively increasing the lift of the airplane.
You've got all the fuel management for six very powerful engines that operated on afterburners
all the time.
You've got the wings that pivot at the tips depending on the speed.
And, by the way, you've got tires.
Every airplane needs tires.
Special tires on the XB-70 were specially made to withstand heat.
The bogies in the back had a little extra wheel as a skid sensor so that the brakes could be
applied correctly because a big heavy airplane landing fast needs to have the brakes applied
correctly.
So all of these things, all of these factors, the engineering smarts required to create this
airplane, they all had to exist in the 1950s.
And those guys coming up with an airplane that looks sleek and futuristic even today
is remarkable.
One thing that we emphasize among Air Force historians and museum curators and archivists
is the differences and similarities between history and heritage.
They're two different things, but they join hands and they join a couple of different
professions together in presenting a picture of our past and making it relevant and interesting
in the present.
So the history part is what happened.
What actually did happen?
And can you prove it?
And what are your sources?
The heritage part, on the other hand, is what do we believe is valuable enough about our
past to pass on to the future?
It's our habits, our stories, our mythology in some cases, what we're proud of, the things
we choose to tell people that we did.
And so with something like the XB-70, we know about its technological history.
We know what it's made of, who made it, what they did with it.
Its heritage is a story about technological progress and breaking barriers and crossing
boundaries and making tools for the Air Force to use to protect the country that crossed
technological boundaries and brought us the future that we live in now.
One of the most amazing factoids about the XB-70 is that even though the airplane looks
like the latest, sleekest, modern airplane, it's two years older than the original Star
Trek.
The airplane first flew in 1964, and Captain Kirk was not in orbit until 1966.
One of the notable personalities connected with the XB-70 is Lieutenant Colonel Fitz
Fulton.
He made 63 flights in an XB-70 and had the most flight time of 124 hours in XB-70A, the
one that we have here.
He worked for both the Air Force and for NASA, and he is an enshrinee of the national aviation
whole thing.
One of the reasons I think that the XB-70 is such a popular airplane with museum visitors
and with visitors online is not just because of its technical features, but because it
is a flat-out beautiful airplane.
It's attractive and balanced in every way.
There's nothing ugly about that airplane.
It just says speed, elegance, and high technology.
It's always been like that.
You can see the XB-70 and hundreds of other interesting, exotic, and historic aircraft
here at the National Museum of the U.S.
Air Force, and if you can't get here immediately, you can go on our website and see all the
same stuff.
And you can even get inside the cockpits with our Cockpit 360 application, where you can
look around the inside of these airplanes, including the XB-70.
So I encourage you to visit and to visit our website.