In this video I show you how to install a Mini Split Air Conditioning System yourself! The unit I used for my workshop is the 12,000 BTU Cooper & Hunter 10 Volt Unit: https://amzn.to/4eaMa8j but the installation steps should work for any of the DIY Kits you can buy online!
Let me know in the comments if you have any questions on How to Install a DIY Mini Split Kit! Love the content? Consider leaving a like on the video, subscribing to the channel, and checking out my patreon: https://www.patreon.com/LeMasterTech
Thank you to patreon supporters Dale Topley and Phillip Nunez!!
what's going on you guys welcome back to
L MasterTech YouTube and in today's
video I'm going to show you how to
install your own DIY mini split air
conditioning unit I have to start with a
disclaimer for a project this big you
need to feel comfortable with
electricity this project involves
hooking up Refrigeration line and if you
do release all of the refrigerant in
your system it can be almost as
expensive as the unit itself to get a
recharge of refrigerant and there's also
putting holes through walls and pulling
vacuum in this project so this is not a
beginner friendly DIY there are some
very serious very difficult things in
this so just know if any of those
Concepts make you uncomfortable it might
actually be worth it to call a
professional but assuming you're the
motivated type let's talk about how you
can install it and not just why you
shouldn't install it now the unit I put
in my garage is the Cooper and Hunter
Olivia Edition which is the Black
Edition because I painted my garage
black my parents have a deli unit I went
with a Cooper and Hunter and I can
promise you the steps in this video are
exactly the same for both and based on
what I've seen online they should be
pretty much exactly the same for
whatever making model you go with a few
things you can do to make your life a
little bit easier before beginning
install are getting yourself a wall
mount or ground mount kit for your
exterior unit and consider getting
yourself a cable guide so you can cover
up all of the wires and plumbing that
are going to go through the wall and two
last things of pre-work you can do are
make sure you have a vacuum pump on hand
if you you don't have one already
they're not super expensive and a lot of
them come with a refrigerant leak
detector I can leave a link to the one
that I got for doing this project and
then the last thing of pre-work is just
locate an available circuit that you're
confident can power your unit okay but
that's all the disclaimers and all the
pre-work let's dive into the actual
steps of installing your own split mini
so your kit is going to arrive typically
in two or maybe three boxes the indoor
unit the outdoor unit and sometimes
there's an accessories box some kits
come with the access accessies packed
into those first two boxes but the first
step is going to be marking and mounting
your indoor bracket onto the wall for
your indoor unit some kits come with a
template other kits just tell you to use
the bracket itself to mount it on the
wall and you want to try to hit a couple
of studs next it's time to Mark and
drill the hole for the cable pass
through to the wall and this is
something important about split minis
the indoor unit condenses a lot of vapor
as it dehumidifies as part of the air
conditioning process and so there's a
leakage hose a drainage hose that feeds
out from that unit so you need to have
an exterior wall but in any case follow
the instructions on your specific unit
on where to Mark and cut the hole to the
outside also all kits specify making
sure that the inner wall to outer wall
is angled downward slightly this helps
with drainage okay so with your bracket
mounted and your hole cut through the
wall next you want to gently bend the
refrigerant lines out of the indoor unit
kind of at a 90° angle and feed the
indoor tooutdoor electrical cable that
should have come with the kit into the
front face plate of your indoor unit
you're then going to need to remove a
few screws from the wiring face plate on
the front of the unit follow the
schematic that comes with your unit most
of the time at this point you have a
line neutral ground and Signal wires
once you're done hooking up the wire to
the indoor unit close that face plate
back up and now it's time to bundle the
four things were passing through the
wall together every kit that I've seen
comes with this plumbers tape I don't
super love it it's not sticky which is
may be the point but all instructions
are very clear you want the drainage
hose on the bottom so that if it does
leak or Kink or anything like that it
doesn't get your electrical cable or
your refrigerant lines wet so take your
four components to get pass through the
wall bundle them together with plumbers
tape just up to the point that they
currently go cut it and possibly fix it
with some electrical tape or something
that is sticky cuz now it's time to pass
it through the wall now for feeding it
through the wall this is probably the
most awkward step in the entire process
if you have a second person around who
can help you get on a ladder on a step
stool or something and help guide these
through the wall I recommend finding
that friend now I did mine on my own it
was extremely difficult and rather
irritating but maybe I'm just being a
baby in any case you have to feed that
bundle of those four components to
refrigerant lines the drainage hose and
the electrical wire all through that
hole and then with them sort of
precariously balanced in that hole you
need to mount the indoor unit onto the
bracket and then get it to sit flat
without damaging anything that you have
fed through the wall and if you get to
this step your inside the house work
other than the final electrical
connection to the exterior unit is done
so at this point it's time to Pivot to
the outside now the first thing you want
to do with the outside unit before
connecting it to any of the stuff we
just fed through the wall is mount it if
you have a floor mount kit you want to
make sure that it's going on a level
surface typically fixed to some concrete
Footers but in any case I leave it up to
you to find a good wall mount kit there
are tons of universal mini split wall
mount kits as well as conduit guides
which I'll also link below if you want
to use the ones I show here now with the
outdoor unit in place take the
refrigerant line connectors that should
have been included with your system and
there should be a thicker and a thinner
one a high pressure low pressure
refrigerant line most kits sell them
with already flared connections which is
nice CU having to flare your own copper
ends is not crazy difficult but it's a
whole new set of tools you're going to
have to get probably just for this one
application in any case follow your
Kit's instructions if there are any
special instructions on how to connect
your flare connectors but in general you
just want to make sure that the flared
part of your copper has a good seat on
the nozzle end of the thing it's
connecting to the refrigerant lines are
flexible because they're made of copper
tubing which bends very easily but
because it bends very easily you need to
be extra careful not to cause any kinks
so being careful not to do any super
sharp turns get those refrigerant lines
connected both to the existing piece of
copper coming out of the indoor line and
then to the inlet ports on the outdoor
unit you don't have to worry too much
about getting these right because
there's a smaller one and a larger one
and the nuts that come with them
typically won't fit on the wrong Port
now with the copper lines connect did we
can get started on pulling our vacuum
which is going to be something kind of
new for a lot of diyers it was new for
me when I did this project but basically
the vacuum pump should come with
everything you need to get started if
you bought any like standard kit so
basically you're going to hook the
vacuum pump up to the middle Port of the
manifold typically you're going to keep
the red valve or high pressure valve
closed and then open the low press valve
blue valve most of the time to the
service port on the back side of one of
the valves on your door unit and at this
point you still have the valves that are
actually going to load the pre-charged
refrigerant into the system closed most
kits say to run the vacuum pump for
around 15 minutes to pull vacuum there's
no reason not to take a little extra
time here give it a half hour give it an
hour pull vacuum you should be pulling
pretty close to the bottom of your gauge
most standard vacuum pumps come with a
gauge that only goes down to like .1
megap Pascal or negative 1 bar all this
vacuum is pulling because I recommend
leaving it going for 30 minutes to maybe
an hour that's a good time to take a
look at connecting the electrical cable
from the indoor unit to the outdoor unit
it's the same wiring as was on the
indoor unit so double check what you did
to the indoor unit make sure that you do
the same Landings to the outdoor unit
this is extremely important and at this
point the only thing we haven't
connected yet is the power from the
indoor circuit that's actually going to
be supplying the whole system to our
heat pump on the outside all right so
once you've pulled vacuum for 15 30 more
like an hour I'd recommend it's time to
test your vacuum so you turn the vacuum
pump off but you leave the gauge
connected okay so most of the time this
just looks like closing the valve on the
manifold the blue valve from your vacuum
pump and then turning off your vacuum
pump this way the gauge will still be
reading the pressure in those lines you
won't be pulling additional vacuum so
for 15 30 minutes maybe more like an
hour if you like listening to me keep an
eye on that gauge because you should be
maintaining the negative one bar
pressure that you've pulled Nega 30 PSI
roughly and it really shouldn't drift or
creep up much from that because you
should have vacuum tight lines so if
after 15 minutes 30 minutes it's drifted
up significantly you need to check each
copper fitting that you made and
possibly break it and retighten it if
you've lost a lot of pressure or try
pulling vacuum again and running the
test again losing your pressure during
vacuum checking is not a step where you
go oh well good enough because if you're
losing pressure that means when you
release refrigerant into these lines
your system is going to drain the
refrigerant within a day I guarantee you
and that is several hundred to have a
professional technician come out and fix
and recharge but assuming your vacuum is
holding really really well then now is
the time to crack one of the valves from
your heat pump to the refrigerant lines
most manuals say only a quarter of a
turn for about 5 seconds and the purpose
of this is now we're going to check each
fitting for a refrigerant leak so go
ahead and crack it close it again and
then using a h hallogen leak detector
which comes with most vacuum pump kits
go ahead and sniff around every copper
connection again in your system and make
sure you're not getting leaks by far the
most common place that you would be
getting leaks is at the connections but
it's not a bad idea to run it up and
down the length of your whole copper
assuming no leak was detected your
system is vacuum tight with the valve
still closed go ahead and remove your
vacuum pump now from the service port
and it's vacuum charged so you're going
to lose a little air when you do that
just try to remove it as quick as you
can and then put the service port cap
back on now with the service port cap
back on your system holds vacuum
appropriately you've tested it open
those valves from the heat unit into the
entire system and at this point your
whole system will be flooded with
refrigerant you can usually hear the
refrigerant flooding into the copper as
you open the heat pump valves you open
those valves all the way put the Caps
that come with it back on and now we're
ready to do the final connection which
is hooking up the power to the heat pump
unit and then we'll turn it on and test
it and do not hook it up to a live
circuit make sure you have the circuit
turned off at the breaker most of the
time you're only going to need three
cables now line neutral and ground from
your circuit into the unit hook up the
power source from your indoor circuit to
the heat pump close that interface up
most of the time you'll be feeding it
through ports in the bottom so screw it
back on to the external part of your
heat pump now you're ready to energize
the circuit from inside if you did it
right you won't trip a circuit breaker
or anything like that and you most of
the time will see the LED display on the
indoor unit turn on now the best way to
test it is to turn it on and let it run
all right my garage is in the Heart of
Texas and it was like a 90° day when I
got it working so I noticed it was
working within a few minutes back within
an hour and the garage was probably 15°
cooler so yeah it was pretty clear that
it was working that is it for installing
your own split mini I know there's a ton
of steps as I said kind of early in this
video this is not a beginner friendly
DIY this is a pretty Advanced DIY which
means you should feel awesome if you do
it yourself but you should also not feel
bad calling a professional if this is
too difficult I will leave links to all
of the hardware that I used below be
sure if you have any questions let me
know in the comments below and I will
get back to you as quickly as I can I
hope you found this useful thank you so
much for watching don't forget to leave
a like on the video subscribe to the
channel and we'll see you next time
thanks bye