This week I build a lightweight, portable stand for the On30 San Lorenzo mini-layout. I needed something that can break down flat for travel, while still looking good with a Southwestern flair. San Lorenzo was originally an award winning diorama built by my friend, the late Verne Niner. Now I'm bringing it back as a tribute to his Estrella & Sonora Grande with this 2' x 4' On30 mini layout.
Thanks for watching, amigos! Dave ____________________ Products used in this video:
Become a Thunder Mesa Member on Patreon for early access, exclusive content, and members only parts and details from the builds! https://patreon.com/thundermesa/
Music courtesy YouTube Audio Library, attribution given where available. "Country Cue 1" courtesy of Audionautix, licensed under a Creative Commons Attribution 4.0 license. https://creativecommons.org/licenses/... Artist: http://audionautix.com "Run One Down" - YouTub Audio Library "Hermanos Ranchero" by Biz Baz Studio, YoutUbe Audio Library
howdy folks dave here at Thunder Mesa's
Studio where this week I'm embarking on
a little carpentry project because I
need to build a lightweight but sturdy
portable stand for the 30 San Lorenzo
mini layout i've been working on this
project for the past couple of months
and if you've been following along you
know that this little layout is a
tribute to my late friend Vern Niner and
his wonderful 30 Estustrala and Sonora
Grande layout and I'm using the
structures and figures and other details
from his award-winning San Lorenzo
diarama got a lot to cover this time out
so let's jump right in and get to work
up until now the layout has been
supported on you know some shop shelves
and boxes and that just won't do going
forward and I like my layouts to be just
a little taller than this right at about
52 in above the floor i find that's a
really nice height for you know being
able to see the whole thing get down
here and you know kind of imagine
yourself in the scene if you want to so
what I need to do is take a couple of
measurements and find out how tall I
need the stand to be so measure
down from 52 okay and then
measure the height of the layout from
the layout deck down to the bottom of
the bench work that's 6 in so we need a
stand that is 46 in tall pretty
straightforward i've got a pretty good
idea of what I want to build here so now
I just need to make a trip over to my
local lumber yard and pick up some wood
and some other materials to make this
happen what did I say 46 in
tall i think I actually want to make
this 45 and
12 because I'm going to have some little
rubber feet on the bottom that are about
a/ inch tall and then that'll bring it
up to the full 46 in
i'm gonna need one two three four six
six pieces this
length this is some uh
pre-stained 1x4s I picked up down at my
local lumber yard um the stain job's not
very good they're they're kind of going
for a you know weathered barnwood look
but you know it's a good start i think I
can make it work
so
basically I'm building these uh kind of
1x4
frames and I want it to be the front
frame will be 30 in wide and then the
sides will be 20 in wide the layout is
24 by 48 so it'll you know sit under
there and they'll be overhang all the
way around which will look nice
um so for the top pieces which are going
to fit in between those
uprightes I need to
subtract the width of two of these
1x4s and of course 1x4s aren't actually
1x4 they're 3/4 of an inch by 3 and 1/2
so that's 7 in
so we
need top and bottom pieces that
are 23
in oh I hate these stupid tags hate them
and then for the sides I need top rails
that are 20 in wide - 6 that's 13 then
minus 3/4 of an inch for the
front
that's 12 and a quarter and I need four
pieces that size this thing's only going
to be three-sided because it goes up
against the wall it can be open in the
back makes it a little
easier i don't mess this up i should be
able to
get all the pieces I need out of this
remaining 1x4
with an inch to spare look at
that can I math or can I
math
okay now we can start putting things
together got this front panel laid out
here on the floor and you can start to
see how this is going to go together
this is the back side so this is the the
inside of the stand i'm
going take a one by
two and attach it here and another one
down there to the bottom 3/4 of an inch
in from the outside so the sides will
fit in like
that and don't worry this isn't the only
thing I'm going to be using to hold this
thing together i'm going to be going in
from the back with screws so you won't
see any fasteners on the front
going to be using some 1 and a/4 inch
cabinet
screws and I don't want to go all the
way through with my pilot holes so use
the old trick of putting a piece of tape
around my drill bit
here so I know where to so I know where
to stop when I'm drilling the
hole slather everything up with some
wood glue first of all
heat heat
okay now the same thing on the bottom
side
now the two side frames going to go
together pretty much exactly the same
way except that now the one by two has
been moved down by an inch and a half
the width of this 1 by two here so that
when it's in place they'll come in right
underneath that one and kind of lock
into place
and the same thing
again down here at the bottom end
okay now I just need to build another
one exactly like this for the other side
okay well you know I had several
different ideas about how to join these
corners in such a way that the thing
will be easy to to you know break down
and travel with um you know I thought
hinges hasps
uh clamps and different kind of clasps
and things like that but what I finally
arrived back on was just some simple
metal corner braces like this you know
put four of these two on each side at
least two and then I just have to
unscrew a couple of wood screws and the
whole thing breaks down now I understand
of course that
um over
time those holes are going to wallow out
uh from from breaking it down and
putting it back up and breaking it down
putting it back up but realistically I
personally I don't travel that much with
these things so you know once a
year maybe i I think um I think it'll be
fine
so the idea is one will be you know be
permanently attached on one side i'll
just have to take out a couple of screws
right there
now I need a couple of removable braces
across the back so I've cut a another
piece of 1x two to
length and we'll
install couple of
these corner brackets on this
well you get the
idea and down here on the bottom I used
a scrap piece of 1x4 and let me turn
this whole thing
around well as my old cousin Virgil
would say it's not a bad looking
squirrel trap so far
let's see if we can dress it up a little
bit and before I break this whole thing
down
again I want to
uh mark each piece so I'll know how it
all goes back
together now this is some reed fencing
that I picked up at the garden center my
local uh Home
Depot and the idea here is I'm going to
cut some uh pieces out of this and then
fill in
uh the each of these panels with it and
it should give it a real you know kind
of south of the border southwesty look
um cool thing about this stuff you know
it's just it's just rustic so you know
it can look tropical it can look
southwesty it just depends on the
application hopefully it'll work and
look uh look kind of cool in these
panels but for this big
panel I need a piece that's 42 in
by
28 since the weave on this is pretty
loose
uh my plan is to double each piece just
kind of fold it over like I'm doing
here cut through each one of these
little connections
then we'll trim it to the right uh
height these measurements and cuts
aren't you know critical just need to
get it in the
ballpark
okay use that for the tiki
bar all
right not bad now got some half inch
staples loaded in my staple
gun go to town
here now let's see how that looks
all
right just what I had in mind
when you guys weren't looking I went
back and uh added some black cloth
behind those wreaths just to make
everything more opaque you know I would
have shown you the whole process but I
figured by now you you probably seen me
putting enough staples really not that
much to it now I think I can finish up
the rest of this back at the studio
okay I've got everything here i just
finished moving the layout off the
shelves and putting it over there moved
the shelves out of the way made myself a
little space to work in and now I can
finish putting the stand together and
get it all back over here where it
belongs easy right i'm going to add
these little silicone rubber
feet to the
bottom of each of the
panels that'll keep them from slipping
around and it'll bring it up to the uh
the final height that I need it to
be some of you may be asking why I chose
not to put uh casters
on it this time and well the short
answer
is didn't think it would need them i
don't intend to be rolling this thing
around very much i may come to regret
that decision but I guess we'll find
out so that's what those feet look like
if you're
curious got all my screws and now I can
start putting this thing back together
again
all right it only took about 10 minutes
to put Humpty Dumpty back together again
before I put the layout on
this couple of little modifications I
want to
make and the first
one is to add a
holder for
my NCE power
cab plugs in right up here so this looks
like a good spot for
it i picked this up over on Etsy or eBay
i can't remember which but if I can find
the link to it I'll put it in the video
description down below it's actually 3D
printed very nicely made and inside
here I want to add a power strip and
this will be the main power for the
whole layout i'll be able to just reach
around the back and flip the whole thing
off or on because all of the various
wall warts and components will be
plugged into this now it's got these
mounting holes on the back for screws
you guys all know this trick take a
piece of masking
tape put it over those
holes like that
you take your
pencil or a pen or a marker of some
kind and you mark where the holes
are then you pull the piece of masking
tape off and put
it where you want to mount that power
strip and it shows you exactly where to
drill the holes
just like that unfortunately I don't
have anyone to help me lift this thing
today it's not that heavy it's just kind
of unwieldy uh I have taken all of the
fragile plaster buildings off so
hopefully this will go reasonably
smoothly what's with your legs
folks if I have this centered on
here there should
be a 9 inch overhang on each side and
you know what
that
looks just about
perfect so I'm going to put a couple of
marks on
here make it easier to line up next time
now the layout will be held to the stand
with four of these sliding bar clamps
which I found are more than up to the
job just uh joining the the uh cross
beam of the bench work to the top of the
stand really
easy there we
go now I can plug the various wall warts
back in that one's for the lights this
one's for the sound
system this one is for the throttle yeah
now I can carefully scooch this thing
back into
position now I can put all the
structures back into place
let's see how we did here on the height
i almost forgot to
measure 52 in the top of the rail
head not bad
now I can plug in the power
cab i'll reach around back here and flip
the main power
on we go
well I won't really know for sure until
I have to move this thing again but I
think it's safe to say that this project
was a success i want to thank you so
much for joining me today and keep in
mind there's more coming on the San
Lorenzo mini layout and the other
projects here at Thunder Mesa Studio so
I hope you're subscribed with those
notifications turned on so you won't
miss those and in the meantime you can
also follow for free over on Patreon
that's
patreon.com/thunder mea or on Instagram
at thunder.m mea or check out the
resources available at the ThunderMA
studio website that's thunder
mesa.studio as always a huge thank you
to our Patreon members who help to make
these videos possible until next time
keep moving forward everybody
adios for now