Looking to coat your 3D artwork in epoxy resin? Good news! You can resin non-flat objects—it just takes a slightly different approach.
Whether it’s a bowl, cube or sculpture, this step-by-step tutorial shows you how to apply a clear, glossy resin finish to uneven objects of all kinds.
We’ll walk you through everything—from setup and to mixing, application, and curing—to help you get a smooth, professional result every time.
Great for artists, makers, and DIYers working with wood or mixed media!
In This Video, You’ll Learn: • How to prep and support 3D objects for resin • How to mix and pour ArtResin properly • How to avoid drips and achieve even coverage • Finishing tips for a flawless result
Don’t forget to like, subscribe, and hit the bell for more resin art tutorials!
[Music]
hey it's Joanne from Art Resin So as you
may know Art Resin was designed to be
used as a glossy top coat that you pour
and spread over artwork But what if you
want to resin something that isn't flat
what if you've got a 3D object like a
sculpture or something that has multiple
sides like a cube well it is possible to
resin them but it's going to require a
different approach Today I've got four
different objects a lantern a bowl a
cube and a sculpture And I'm going to
walk you through how to resin each one
So I'm going to go grab my supplies and
let's get started
[Music]
So first let's get started with our
lantern Now this is made out of a
hollowed out stump and I want to put
resin on it to make it weather resistant
so I can put it outside Now obviously I
can't pour the resin over It's just
going to run off and make a huge mess as
well as waste a ton of resin So what I'm
going to have to do is apply it with a
brush Now art resin has a beautiful
honeylike consistency and it is going to
brush on really nicely Now you could use
a foam brush but because the bark is so
rough it is going to shred that foam and
you're going to end up with little black
bits cured into your resin So what I'm
going to do instead is use an old
paintbrush But just remember if you do
this you're going to have to toss it
after you're done Another option is to
use your gloved hands You'll also want
to tape off the bottom with good quality
tape to catch any resin drips And then
after it's taped you want to burnish it
down really well A ruler works well or
your stir stick And this is really going
to help it adhere to the wood Then prop
the piece up on your stands Plastic
stands work great because any resin
drips will peel right off So now that
the piece is propped up you can go ahead
and apply the resin Now it's important
to remember because this is raw wood the
resin may make the wood appear darker So
it's important to do a little test first
with water and this will let you know
what the wood's going to look like once
it has resin on it In many cases the
darker color looks beautiful But if you
don't want a color change sealing it
first with a wood sealant or something
like PVA glue will help prevent this
color change So now I'm going to prepare
my art resin I'm going to mix equal
parts of resin and hardener in a plastic
container And I'm going to mix it for 3
minutes making sure I scrape the sides
and the bottom so it's all thoroughly
mixed So when you're brushing resin on
it's important to be mindful that
gravity is going to pull the resin down
So you don't want to apply too much or
all the resin's going to run off or
you're going to end up with a ton of
drips on the bottom If you do want a
thicker coat though it's better to work
in layers Applying multiple thin coats
one at a time And remember because
you're applying a thin coat you need
less resin than you think you might So
the best approach when you're working
with a piece like this is to work in
stages because once I coat the main body
the resin's still going to be wet So I
won't be able to flip it over and coat
the bottom So the best approach is to do
the main body first let it cure for a
day and then you can flip it over and
resin the bottom So now that our resin
is applied the last step is to torch out
any bubbles apply a dust cover and then
let it cure So tomorrow when I come back
I can just remove the tape and then
apply resin to the bottom Now if I did
want a thicker coat all I need to do is
give the cured resin a light sand then
reapply and then repeat those steps as
many times as needed to get the
thickness that I want But at this point
I am really happy with how this looks
So a bowl is another really popular item
to resin but because the sides are
curved rather than straight like our
lantern was I'm going to have to resin
the inside and the outside separately So
I've already gone ahead and resin the
back but before I did I taped the inside
of the bowl along the lip to prevent any
resin drips So now I'm going to flip it
over and resin the inside And again I'll
tape around the outside to prevent any
drips It's important to remember that
gravity is going to pull the resin down
to the lowest point So if you apply too
much resin you may end up with a thicker
layer on the bottom of your bowl So go
slow use less resin than you think you
need And remember you can always add a
little more if necessary So once you're
done cover it and let it cure for 24
hours Then remove the tape And just to
make sure it's food safe let it fully
cure for another 2 days before you use
it And then you're
done So now let's talk about a piece
that has multiple sides I've got this
decorative cube here and I want to resin
the whole thing Now if I were to pour
resin over the top and let it run down
the sides gravity is going to pull the
resin and I'm going to end up with a
thinner coat on the sides than I have on
the top So the better approach is to
work in stages applying resin to one
face of the cube at a time and
continuing until all the sides are done
I'll start with the top panel let it
cure and then flip the cube around so
that one of the sides becomes the top
and then continue until all the sides
are resined The advantage of doing it
this way is that you're going to get a
nice thick coat on each side I
definitely tape around each side as
you're going just in case you get any
drips And if you apply the resin
carefully you shouldn't have any issue
where the resin meets up along each edge
of the panel If you do have a gap or the
resin overlaps and the edges become
uneven or bumpy then you can just sand
it down lightly with an emery board and
reapply with a foam brush So for an item
with multiple sides like a cube the best
approach is to do it in stages It takes
a little bit longer but the results are
so worth it
So here I've got a bunny sculpture that
I'm going to resin to make it weather
resistant so I can put it in my garden
And again because the stone has quite a
rough surface it's going to shred a foam
brush So I would either use an old
paintbrush or gloved hands I think for
this one I'm going to go with gloved
hands This way I can really get into all
the crevices and I can wipe off any
excess resin so we don't end up with too
many drips Of course it's always a good
idea to tape off the bottom before you
start
Again you may need to work in layers if
you want a thicker coat Once the resin's
dry you can flip it over prop it up and
apply a thin coat to the bottom of the
sculpture Let it cure for 72 hours and
you're
done So I hope you found this video
helpful If you have any questions or
tips about how to apply art resin to 3D
objects please leave them in the
comments below Don't forget to hit
subscribe and we will see you next time
Bye
[Music]