okay guys here are all of the parts
you're going to need to build this right
here of course you got to have your
cooler and I'll have all these parts
listed uh in the description you've got
to have your pump you're going to need
PVC pipe you're going to need multiple
connections to make it fit to run
through you need a screen that's really
important I don't know if you've ever
kept mullet in a bait tank or anything
but uh they crap like they ate at Taco
Bell the night before so you're going to
need the adhesive Fast cure uh you're
going to need a bit to drill the hole
through the cooler clamps for the
hose um that's all that ought to do it
so let's get
started all right the first step you got
to figure out where you're going to
put your input and your output so your
pump is going to come in here just like
this into the side you're going to have
your screen on it and this lock nut
it'll stick that through and the lock
nut will go on hold that in place of
course we're going to glue everything
with the sealant we can do it over a
little more let's do it right there less
to drill
[Music]
through okay we're going to want our
hole about right
there
okay start
like
[Music]
that okay got through
there okay we got our hole so now we can
go in from this side make a nice clean
[Music]
cut
Perfect all right all right let's test
that
fit we're going to want that like
that it's going to go there like
that and we're going to have the super
hard cement on there
and like that this is going to be here
like this got to figure out where we
want
it about right there going to want
placement of this so we don't want it on
that so I'm thinking about like
that right
there all right let's get this hole here
done
now got that one let's go from this
direction should be all the holes we
need so this is going to slow slide in
here like that you'll have your end cap
on
here that sticks out there just like
that so yep that'll
be perfect now we got to cut a piece of
hose to
fit it's going to go
to there
okay just going to want it cut
right
there all
right sharpest knives I got in the house
are my sword fle knives
so
just there we
go all right now let's level it
out put that on here like
this okay we got clamps for
this we going to have to glue
that
see should be easier to get onto this
one
perfect there we go that's going to be
stuck like
that so after dry fitting the whole
thing then you want to take it apart and
start gluing it with the PVC glue make
sure you glue everything except for the
incap that goes on the spray rod that's
inside otherwise you're not going to be
able to fit it through the
hole wanted to get this
set so we'll
know where to drill the holes all
right okay so we got that fitted
right angle's going to be about like
that so we're going to have the cap on
here it'll go right there like
that like that right
there so let's see we're going to want
our spray
holes i' say about right there
so I Mark the holes every 2 in and you
want to do this after the PVC glue has
dried so it doesn't twist and they're
pointing in the wrong direction all
right so we got all our holes marked so
now we're just going to drill a hole
each one of
these okay got all all the h H drilled
let's put it back in see how it
looks okay all of our holes are pointed
down all
right looks like we are about ready to
start gluing let's go ahead and get the
PVC done on this just didn't want to
drip it in
the cooler all
right and I'm only going to put the glue
inside the cap because when I push the
rod through the hole going to the cooler
I don't want glue dripping on the
inside get that back through all
right okay
all right now it's time to get out
the the
glue I want to get these pre-drilled so
before that Drew
cures okay
okay all right so we got those two holes
pre-drilled uh we're ready to start
glowing we're good all
right all right make sure your washer is
in
there luckily I saw
it that would have been bad glue it all
together not have the washer in there it
had water spewing
everywhere so yeah make sure that gasket
washer's in there all right so first
things first we want to get a bunch on
the you really can't use too much of the
sealant you want to make sure every
little Gap and hole in the cooler is
filled
and this sealant pretty much permanent
so that's why dry fitting everything
beforehand is so
important and I also tried to get both
sides of any two points that we're going
to touch this helps ensure that there's
no gaps in the sealant
you even want to make sure and use the
sealant on the screw holes before you
put the bracket
[Music]
in and I went through with my finger and
pushed everything down and smoothed it
out and make sure that that sealant was
getting in every crack and crevice all
right all right looks like we got
everything sealed up
[Music]
tightened so now we just got to wait let
it cure and then we'll come out we'll
give it a
test all right guys we got the bait tank
done pretty much we got like one little
more step in the process I'm going to do
that right now it's pretty easy simple
deal all we're
doing is putting these clamps on the
wires so it'll make for good attachment
point on the uh
battery and soon as we get that done we
will turn her on and test her out these
are just battery Clips you get at
Walmart probably get them anywhere main
thing
is you just want to have plenty of
contact all right I think we got that
one
all
right okay we got that soldered let's
get our pliers and get those squeezed
down okay got that one
done all right okay guys got the battery
right here
suck it up for the Moment of
Truth all
right and this cooler since it's got the
drain makes it really easy to take care
of
it just want to let your water out
there you
go all right hope you guys enjoyed the
video uh pretty easy
build uh it's not tough at all but it
could really make for some good days
fishing so uh don't forget like And
subscribe and I'll see you guys on the
next one