Este motor tiene una VALVULA en el PISTON 🤯 Motor Rotativo Radial

Machine Engine
3 followers
In this video we have the Rotary Radial engine.
We will see the Gnome with its famous valve in the piston.
The monosoupape, which had a valve and ports
And the Le Rhone. The last one was more efficient, although conventional.
The first ones did not have a carburetor, only a pseudo fuel injector.
3 machines that dominated the skies at the beginning of the 20th century.
One of them was commanded by the Red Baron in his plane.
#engine #repman22 #rotary #radial #turbo #4stroke #2stroke #machine
Comments are disabled for this video.
This engine has a valve in the piston, which was automatic and worked without any type of command.
It did not require chains or camshafts.
It was enough to have some counterweights with springs to allow the opening and closing of it.
In addition, it was large, basically the entire diameter of the piston,
which allowed an ultra-fast exchange of gases.
We are also going to explain this ring that it uses in the shape of an L,
and why the entire engine rotates, while the Zigeuner remains still.
Today's engine is the French Nyon, and with its rotating cylinders,
it was the most used design during the First World War.
A German version would drive the Red Baron's plane itself.
Today, when saying rotating engine, one thinks of the Wankel,
but the reality is that this term initially belonged to these engines.
It was the year 1908.
The Zegeuner brothers presented the engine at the Paris Air Show,
capturing the attention of everyone.
The advantages were obvious.
At that time, the engines produced very little power,
and they also needed very heavy inertia flywheels to maintain optimal operation.
Weight is the biggest enemy of an aircraft.
The Nyon eliminated the flywheel by replacing it with the carter's own weight and the cylinders.
The vibrations were smaller than those of the conventional radial engine,
since the pistons also had angular velocity.
With 8 liters of engine, 7 cylinders and gigantic intake and exhaust valves,
being of elongated diameter and length and compression ratio of 5 to 1,
rotating at 1500 rpm, it initially produced 50 horsepower.
The Forte had 2.9 liters of engine and produced 20 horsepower.
If we make the comparison by duplicating the T engine,
we get similar numbers in power, although this one needed a radiator.
The Nyon, when turning, ensured an exaggerated amount of air that embraced the cylinders uniformly,
making it lighter, which made it special for aeronautical use.
The propeller rotated at 1500 rpm.
At that time, not much was understood of propellers,
but it was known that the tips should not exceed the speed of sound.
In addition, the diameter was limited by the height of the aircraft to the floor,
which resulted that 1500 was the ideal speed.
The rotary engine proved to solve all the problems that the other engines of the time had,
being completely inverse.
Let's see in detail how it works.
First we have the wing, which was hollow and was attached to the aircraft.
At the end was the carburetor.
Inside the wing, in addition to traveling the mixture towards the carter,
there were also the pipes that carried the oil to release it inside the engine.
As we see, the entire carter makes multiple admissions
and contains all the mixture of air, fuel and oil.
The carter is attached to the wing by bearings, which allows its free rotation.
Then we have a master connecting rod and several slave connecting rods.
Each connecting rod handles a piston, which in turn has an automatic valve.
This automatic valve has a system of counterweights and springs,
and when it goes up and then turns,
the inertia and vacuum it generates while it goes down usually opens it.
Then, when it turns and starts to rise,
the inertia and now the compression close the valve.
Now we add the winged cylinders.
At the top of each cylinder there is a large valve,
mounted on a threaded system that allows it to be easily removed for maintenance.
This valve is commanded by swingarms and rods.
The cam tree is hollow and rotates on the wing at half the speed of the engine.
It is driven by gears.
If we pay attention to the follower of the cam tree,
we can see that it is completely circular and surrounds the cam.
It is similar to the letter D.
This makes it act like a Ducati demodronic system,
where it opens and closes the valve at the same time.
This is because the valve is very large and the whole set is very heavy.
Remember that also the whole set rotates and is subjected to centrifugal forces.
A bad balance in the weights of the valve and rods
could cause the valve to open at high revolutions.
But with this system where it opens and closes, this does not happen.
To help with dilation tolerances and others,
the valve also has a spring to keep it closed.
Each cylinder has its spark plug.
Then a wire connects it to the ignition system.
The carburetor always operated at 100%.
Although it has a regulation to adjust the air
and try to find the relationship between air and fuel to make the mixture,
the reality is that the butterfly did not serve to regulate the speed of the engine.
This is because the peak that released the fuel was primitive and did not spray the mixture well.
It did not have Cuba or Venturi effect to suck in empty.
The carburetor had to operate at 100% to make it work in an acceptable way.
The mixture could be put a little out of the ideal to slightly reduce the speed,
but the quick way was by blocking the spark jump.
The pilot can press this button and turn off all the cylinders,
as well as some could be deactivated.
Obviously the deactivated cylinders continue to receive the fuel that will not burn
and will come out of the exhaust raw, wasting.
However, the power regulation was only used for landing.
The planes had little power and were not as fast as to need to regulate it,
so they went to the whole machine.
Now this engine is 2 or 4 strokes.
I'm going to freeze the housing and allow the butterfly to turn
to make it easier to explain with a single cylinder.
Well, the mixture enters through the hole.
While the piston descends, the vacuum that is generated
causes the piston valve to open and the mixture to enter the cylinder.
When passing through the lower dead point,
the inertia and compression cause the valve to close.
The compression of 5 to 1 is reached and the spark is fired.
The high pressure of the combustion keeps the admission valve closed.
Then the exhaust valve opens and the burned gases come out.
Now the cycle is repeated again.
Admission, compression, expansion, exhaust.
As we see, it is a 4 stroke engine.
If we look at the engine from the outside,
we see that the ignition always occurs in the upper piston.
We also see that it is a yes cylinder and another no.
This is because the 4 stroke engine needs 2 laps to complete the cycle.
On the left we have the expansion and admission zone.
And on the right, the compression and exhaust zone.
The order of ignition is first the odd ones and then the even ones,
being 1, 3, 5, 7, 2, 4, 6.
Here you can see how the piston goes from the upper dead point to the lower one.
And now it goes up.
This view allows you to see everything clearer without annoying things.
To reduce friction due to lubrication that was not the best,
the engine used bearings everywhere.
Now, why did the piston have this ring in L?
The winged cylinder was made of nickel steel
and to weigh less than 2 kilos each, the thickness was only 2.5 millimeters.
With thermal dilatations and use, the cylinder deforms
and after 20 hours of use, all the cylinders had to be replaced.
But with the ring in L, this was flexible,
helped to pack the combustion and adapted to the irregularities of the deformed cylinder,
sealing and maintaining the high compression,
raising the useful life to 80 hours of flight.
The problem these engines had with the valve in the piston
is that sometimes the counterweights got stuck and the engine had to be disassembled.
So then, the valve was replaced by a blind piston
and light bulbs were installed in the cylinder.
Now, the engine would be called a monovalve or mono-soap-up in French.
This engine had the light bulbs in the lower part.
The piston went down creating a vacuum and when it reached the light bulbs,
the accumulated vacuum forced the rapid intake of gases.
But there was a problem.
As it burned, while the piston went down, it reached the lower part
and the fire could pass to the carter, which was full of mixture waiting to enter,
which caused the entire engine to explode into a thousand pieces.
Remember that it was made of very fine and light steel.
To solve this, the exhaust valve would open very early,
since it was very large, it allowed all the exhaust gases to come out.
Thus, the pressure of the cylinder was lowered and when the piston reached the bottom, there was no risk.
Then, the piston went up emptying the few gases that were still left.
During the night, this process allowed to see the fire coming out of the cylinders,
since there was no multiple exhaust.
This would also drastically reduce the power of the engine,
since the expansion race was not finished.
Although it was more reliable than the engine with the valve in the piston.
This allowed it to add several hours of flight before having to disarm the engine.
You may have noticed that the 36 light bulbs are very thin.
Remember that the cylinder was 2.5 mm thick.
Therefore, as the engine could not be powered here,
the solution was that, after the exhaust race was finished,
leave the valve open so that the fresh air enters.
When it reached two-thirds of the race, the single valve closed and the engine created a vacuum.
When it reached the light bulbs, this vacuum sucked in what it could of mixture.
It must be clarified that this mixture was ultra-rich in fuel,
so that later it mixes with the existing air.
As you can see, the single valve of the engine performs the task of exhaust and intake.
Hence the name of mono-soap-up or mono-valve.
Other versions solved this with ports that went outside the cylinders.
Subsequently, the intake valve was added at the top with intake duct,
giving rise to the Lerone engine.
It stood out for having a single rod to operate the two valves.
A swingarm could swing to both sides, pressing one or another valve.
With nine cylinders, the power would increase up to 90 horsepower.
This engine could now be controlled by butterfly in the carburetor,
which improved fuel consumption.
A German version of this engine would be commanded by the Red Baron during the First World War.
Planes with this engine, due to the gyroscope effect of the rotating cylinders,
tended to bend quickly to the left, but very slowly to the right.
They also consumed a lot of fuel and oil, and the plane was effective in short flights,
since for long flights they had to transport more fluids and lost the advantage of the low engine weight.
In this video you can see how everything in the back is shiny due to the oil impregnation.
In addition, using the short-circuit, you could make the plane soak in fuel.
Plus some flames that came out of the engine, the wooden plane could catch fire.
The Nihon engine consumed 10 liters of Castor oil per hour of flight.
Castor is a type of thick natural oil widely used to lubricate engines,
and from this derives the name of the Castrol oil brand.
This engine has similarities to a two-stroke,
such as using the crankcase to have the mixture and burn oil, or even the fireplaces.
But for a radial engine to be able to do two strokes,
it would need at least a compressor or a turbo to speed up the crankcase to be able to do the intake.
In the four strokes, it is the piston that lowers that creates vacuum,
and in the case that the two strokes does not want to use turbo for the intake,
it must have the crankcase separated internally for each cylinder.
Thus, it uses the lower part of the piston to suck.
Subsequently, the radial motors of the rotary cylinder were replaced by the fixed radials,
since with the increase in power in the years to come,
not consuming oil, better understanding of air cooling and more durability,
ended up being better than the rotary ones, making them forgotten.
However, these engines were the correct answer for that specific time,
and to this day we are still hypnotized when we see these engines spinning like crazy.
At that time, there was also a motorcycle with a small rotary engine
adapted to the front wheel.
There were also versions without the D in the follow-up of Levas.
If you want to be like me, I have a course that ... no, lie.
If you got to this part of the video, don't forget to leave your super thanks,
to like it and comment what you think.
Don't forget to share it with your friends either.
My name is Francisco and see you in the next video.
