Somebody BROKE The Gripper Arm Off This AMI Rowe Tropicana Jukebox!

Joe Jukeboxes
160 followers
903 Video Views·Mar 10, 2025
Joe's Jukeboxes is our channel sharing all the repairs we've recorded videos of over the years. If you've got a jukebox that needs repair, if you watch our videos you may be able to fix it yourself. There are playlists here on the channel of each manufacturer, keep in mind that the boxes usually used similar if not exact mechanisms from year to year, so if you can fix one Rock-Ola, others will be very similar.
This channel is a subchannel of our main channel @JoesVideoGames !
ladies and gentlemen this is Joe's
classic video games back with another
cool jukebox repair video for you this
evening we are working on this
1964 row Ami Tropicana jukebox I believe
it was the
jbm model um and we did a video on it
already so the if you missed the
previous video we were having all kinds
of uh first we couldn't even get it to
turn on then we figured out how to get
it to turn on and then uh we uh had some
problems with the selector so basically
the um whenever you hit the buttons it
would act like it was selecting
something and then it would um spin
around and never find anything so we
tracked it down to it wasn't actually
pushing in the uh the little pins on the
pin bank and uh we eventually figured
that out by cleaning off the connections
on the keyboard and we've got it working
pretty good now um that part of it so
the collection of system appears to be
working properly it's doing the the read
in and then it's not uh the right in but
it's not doing the read out completely
yet because the gripper bow is missing
off of the machine so luckily back in
the day I was able to find a used
replacement gripper bow so we're going
to put that on and uh check out a couple
things the first thing I'm going to
check I'm going to mess with though is
whenever you select something and by the
way the latch coil is missing on this
one so you have to hold the the UTS down
if you if you select
one whenever it
transfers it'll eventually get to where
it finds the
record notice our turntable is not
actually spinning it's because it's not
in the right
position the uh The Idler Wheel isn't
touching the sides of the turn table and
I haven't messed with any of these Amis
so I'm not sure why that is but it's
basically we're sitting up too high so
the first thing I'm going to do is
figure out how to get that turntable to
go down so the Idler Wheel can ride
beside it and actually turn it like it's
supposed to we're also missing the
needle um in our cartridge we've ordered
one it's coming
right so let's figure out why the
turntable is not in the right position
first
all right so it's trying to play a
record right now and The Idler Wheel is
right here if you
look it's kind of like slipping out of
place I'll take this off and show you
how it does it here in a
minute but you can see what's happening
it's kind of
working but it will eventually slip out
of place
and end up under the
turntable this one of those things where
it's been sitting for so long it kind of
just needs to run a little bit too but
um there's obviously some adjustments
off
there all right so I'm going to let it
run for a little bit and then I'm going
to take this platter off and we'll we'll
look at the uh the ID whe assembly under
there all right so the turntable is
still turning and turning and turning
and
turning since there's no record on it
the it'll never end but uh this is what
the motor shaft looks like it comes up
through through this little plate and
then there is an Idler Wheel
here this shaft is spinning pretty fast
and this little wheel is rubber and it's
up against this and so it is also
turning okay now the other side of it
touches the turntable itself so there's
a post over here which is kind of the
center of the
turntable and so that's what spins the
turntable this shaft spinning the side
of the wheel now why do they do that
instead of it being like a direct drive
it's just how they were designed and it
it's it's also said that they can change
the
speed so The Idler sha the uh turntable
shaft has three little levels
here okay there is a coil over here that
can pull up or drop down right and so it
essentially you've got this big arm
there's a spring on here so that it
holds it up against the uh the shaft but
um basically this can ra this whole
assembly can raise in the air or fall
down depending on how what this
does now why would they do that it's
because if it's up
here uh it's spinning slower and if it's
down here it's spinning
faster just because the the the
thickness of the the motor shaft is
different now why do they need it to
spin two different speeds because it's
so it can play 33 uh RPM records and 45
RPM records
so it's kind of like you don't you know
there aren't even that many 7 in 33 RPM
records that anybody's going to put in a
jukebox but they went through a whole
bunch of trouble because at the time
they were trying to kind of push
that um if you have it play at 33 RPMs
you can squeeze an extra bunch of music
on the same exact 7 in
platter so I don't I don't know why they
did that I guess for so it could play
LPS or something I'm not LPS EPS is it
EP but anyway that was some stuff they
were trying so it can play two speeds
right so that causes you all kinds of
problems though if if it doesn't work
right so they're saying adjust the speed
shift coil so that the rim of the
idler clears the step in the motor shaft
by at least 132 of an inch in both the
full up and full down position of the
coil
plunger when checking this adjustment
pull the idler away from the motor shaft
and then release it it's they're saying
that so that you don't move it up and
it's kind of sitting crooked on the
motor sha the coil
frame will pivot slightly about the top
mounting screw hole
just
enough to allow an up and down
adjustment of The Idler and
linkage so if you if you pull
this it actually kind of flexes
this right so if this if the top pulls
out that's going to raise The Idler up
on this if the top goes in that's going
to lower the ID idler down on this now
there's another issue though to check on
yours
this turntable motor has little
rubber
um um
bushings that grommets they call them
grommets that attach the turntable motor
to the plate and the rubber so that it
doesn't transfer the noise of the motor
into all of your stuff right there where
you're playing the
record those rubber things get they they
dry out over time especially over 55
years okay so sometimes you have to
replace those if you're looking for
parts for these you can get them at
there's a place jukebox parts.com that
carries a lot of the service parts
that's who we usually use right but if
those rubber grommets dry out over time
and this motor drops a little bit well
then the shaft drops a little bit so now
the idler isn't in the right
spot okay so whenever the coil is
down it should be at least 132 of an
inch below this
hip and then when the coil is up and it
pushes it up for the other speed it
should be at least 132 of an inch above
the
hip so I'm going to mess with that a
little bit make sure we've got that
right and also this Idler Wheel you can
buy replacement ones again from jukebox
parts.com but uh sometimes you can just
clean them and they work pretty good the
problem you get is if you get a bunch of
oil embedded in
it uh it slips and doesn't grip right
it's it it's supposed to be a little bit
tacky not like crazy tacky but like
everything has kind of a tack to it like
this is real smooth this is a little
more tacky you know so rubber has a
little bit of a attack to it um and it's
just so that it can grip the uh this and
the platter when you put it back on
there because if it's completely
smooth uh it's not going to spin it
right it's going to slip on it so you're
going to lose some of your speed and all
that especially when you have a little
bit of weight on the turntable from the
arm and the uh the record actually
laying on it so uh let me check all this
stuff out and see what I can find and
see if I see any problems all right so
let me show you something now I am not
an over technical person obviously you
can tell by the way I'm talking right do
I look like I do technical stuff I don't
need to do or maintenance stuff I don't
need to do so I'm with you I understand
you don't want to do this stuff right
lubrication
chart do not over oil but look what
we're looking at
here it says that you should put oil on
the three
pivots of The Idler Wheel assembly
right so it's all you know riding dirty
basically I'm going to take this one off
I've ran into this before I'm going to
take the Idler Wheel off and show you
what it looks like there's a little
clip and then The Idler Wheel
now you see how it
is it's kind of like a loose fit so it
will spin around this thing well this
thing was pretty much seiz to the shaft
but if you look on that uh picture it
said that you want to oil this the shaft
not the outside of it the actual shaft
okay
so I don't know if you can
tell so this is our assembly there's the
co the coil things down here that can
raise and lower this arm right so this
is what The Idler Wheel attaches to and
I could I can't really prove it to you
but it's just covered in like dirt and
grease and all screwed up right it's
filthy and real
sticky now why is that it's because it's
oil that's like
probably 40 years old I I would not
doubt that it's been 40 years since
somebody oiled that thing and it says in
the manual to oil it every six months
one drop of
oil now like I said I'm not the type to
do that all the time you know and to
make sure that I'm a stickler by the
book but come on people every 40 years
ain't going to cut it so I think that's
part of our problem so I'm going to oil
all that I'm going to make sure that
it's adjusted where it hits that shaft
right and then we'll put it all back
together so here's our Idler Wheel let
me show you what you'll run into look on
the edge of it see that little Dent
there there's another couple of
them there's a bad
one another bad
one so there's three significant ones so
what is that from it's from the thing
sitting that that one Dent is for 20
years you know it sat there touching the
motor shaft for 20 years without moving
and then somebody got it running again
and it played a SE several
records and then it sat there in another
spot for another 10
years and that one that was kind of
shallow that was probably only six
years so those dents this thing will
still work with those on it but you'll
get a little bit of flutter so you'll
get it'll it'll slow down and speed up
the the record a little bit and it'll do
it every time this turns around whenever
it gets to that dent it'll move just a
little bit it won't be quite be
right so
um depending on how much that drives you
crazy you can buy a new one of these to
replace it or you can also sand it you
can sand down the edges but you kind of
got to do it even or you screw up the
whole
wheel now you might say well if you sand
it you'll make it too too small if you
sand a whole bunch of it off you'll make
it too small but the way the thing is
designed it
actually it's hard to understand this
but take my word for it the diameter of
The Idler Wheel doesn't really matter
the diameter of the platter matters and
the diameter of the um motor shaft
matters but all this is doing is making
this movement go to this movement it
doesn't this can actually be a
completely wrong size and it'll still
work at the same speed
look people I didn't invent it I'm just
telling you the facts so I uh I'm going
to sand it a little bit by hand but if
you if you're ve if you're not careful
you'll end up with like a flat spot and
it'll be even worse right worst case you
can buy a new one they're like 30 bucks
right um but that's something to look
out for you can also just leave it alone
leave it how it is and uh if you don't
like the sound then you can get a new
one right so if you get a a warble in
your in your juke box check out The
Idler The Idler
Wheel okay so she seems to be spinning
nice and clean I don't know looks like
it's got a little bit of
a something going on there but it may be
an optical illusion
too and we don't have the turntable on
there so we'll figure it out but um yeah
that's what you look at if you're having
issues with warble or whatever it's at
the right spot on the uh Sha I was able
to adjust that a little bit
by taking those uh those two screws
loose
there and then moving it like it said in
the
manual so let's put the platter back on
all right so I think we've got that all
adjusted how it should be so I think uh
it's at least worth
testing we still got some other issues
but uh by the way just to remind you
there's no needle in this um arm and
then also usually this would cancel
whenever it sets down but there is you
know I bought this machine off of
somebody else it's had a hard life
apparently but there's probably a wire
that goes here that cancels it so if it
goes down and it doesn't land on a
record it goes a little too far this
metal screw hits that plate and cancels
it so we'll figure that out eventually
which wire goes there there's a couple
wires just hanging there but they kind
of look like speaker wires but that's
not super important and it's actually
kind of helping us test it at the moment
okay so the next thing I think we're
ready to do is to uh replace the gripper
arm so if you didn't see the previous
video the gripper arm was broken off of
this machine we bought it off somebody
and you know it was the the typical oh
everything works great uh it's just the
gripper arm's been broke uh needs a new
gripper
arm
um I can't completely tell where it even
goes I guess this is it here but have no
fear I bought another one now this is
the broken
piece they were nice enough to give me
that which really helped cuz at least I
could get another one so first I ordered
this
one but it's the wrong one looks very
similar very similar but it's slightly
different and then
I ordered this one this is off of an
mm2 and it appears to be the exact same
dripper arm so I'll take it out of that
bag and uh just like always in the
manual it kind of tells you how to do
this all right so in the manual it says
how to install the transfer arm
assembly one rotate the transfer motor
shaft until the sector gear is in the
maximum down
position h
wonder where it that
is let's see if we can figure out how
that goes so it appears that's how it is
so basically the arm would be laid down
right now because it's trying to play
the record so we're sitting here with
the turntable still running I'm trying
to basically I found on these some of
these jukeboxes before that if they've
been sitting a long time the uh
turntable motor may be a little slow or
something and it just kind of needs to
run a little while get the Kinks worked
out but that kind of to me looks like
how it's
uh how it is in that drawing I believe
that's what they're saying maximum down
position so the the arm would be down on
the turntable and the gear that wedge
shaped gear is turned so that that
smaller gear there is at the top just
like
that two turn the record release cam so
that the gripper Jaws are
retracted and the hole in the cam is is
down so here's my replacement
one
so this plastic thing here I guess you
can turn yeah and that's what pulls this
in so like if that's out it's grabbing
the record but then it gets to a certain
point and that oblong there turns like
that
I can do it with one
hand I went too far I think I think I
went too far yeah I did it goes the
other
way
okay boom that's kind of how they have
it so there's the
hole are retracted and the hole in the
cam is down
okay
three move the transfer
assembly down between the supports on
the
base oh yeah they're telling you how to
install
it insert the two bearing
pins so that the holes in the pins are
aligned with the retaining screw holes
in the support I've got those too H
thread the retaining screws all the way
in so we're putting it down how we've
got it turned right now we're going to
put the little post through the
side and then little screws go into the
holes on the side of
that so this is kind of
like that right and so these pots these
little things here you would turn to the
side side so that the screws will go
through the
posts and I guess by doing that with it
oblong like that I might have to turn it
one more tooth Whenever you set it down
the the teeth will mesh up just right
with the
gear okay so I'm going to go try to pull
the other one out first okay so the old
one was really easy to take out just
like they said you listen the two screws
on the front
which means they're no longer through
that hole and then you can just pull
these right out of the side once you do
that the whole thing comes out easy
peasy so I removed the old one but then
I was looking at
it and with the record down it wasn't
like they were throwing in the manual so
they must have meant they want it down
as then hung all the way
up right because that's when it looked
like
this so I canceled the record it
returned it all just like
that then I took the two the two things
out and slid the other one right
in and we've got it mounted back in
there and who knows if it works I'm
afraid when I test it it's going to
break the
arm something broke the arm before
people what what do you think that could
have even
been what if it breaks my new arm as
soon as I do it
what do you think let's try
it there's only one way to
see I I'll put my hand on the power
switch just in
case come on baby don't break on me baby
come on now I'm trying to help you don't
break on me now come on now why would
you do
that
bam it dropped it down just as pretty as
you
please that's pretty cool okay let's
cancel it is it going to break it when
it hangs it up what if it hit something
and that's what broke
it perfect perfect it's working
perfect all right
well I don't know sometimes stuff like
got brakes cuz people pull on it maybe
somebody just broke it I don't I don't
know how would I know people I wasn't
there how would I
know if you read the Sherlock Holmes
books he said one time in the book he
said that if you have one clue you
should be able to figure out everything
that happened just from that one clue
one piece of evidence so I've got a
broken bow gripper bow I ought to be
able to figure out how it broke but I
can't all right
so here are the sixes this is C6 we'll
try C6 which would be this side so what
record what test record are we going to
waste in case it snaps it in
half the bill black
combo white Silver
Sands and my
babe all right so let's see six
C C6 I can't do it with the
camera it's too far
away I need it to be down here so I can
hit them both with one hand
uh let's see here I can put it over here
yeah that'll work
6s I might be able to reach that
one okay
S6 I hope it don't break my record I
don't even know what record that is but
I don't want it to break
it what
a
Wham holy moly now notice it it flipped
it that way and the arms on this side so
we need to do the other side just to
make sure that it can do that so
6t
T
6 now I can put that in while it's
playing the record it should hang it up
and then I don't know if it'll
immediately grab it or if it has to go
around once but I'll bet it I'll bet it
immediately grabs
it
no break on
me all right I think we figured out our
problem the basket is just slightly off
it looks
like mhm that could have done
it when I moved it when I wobbled it
like
it see if that wasn't all the way
down and the carousel started
turning it would snap it look how it's
stuck there something ain't
right I don't think I should be able to
freee that look how I can just turn
this yeah look I shouldn't be able to do
all that
surely
hm on all the ones I've done before
there's no play in them like
you it's where whenever it's halfway
through the thing it's stuck there you
can't just free will it like
this so something is not quite
right sounds like we're scratching the
hell out of the record
to
all right so that's the next thing we
need to figure out what's going on with
that okay so I've been playing around
with
it and you can see the problem is it's
actually hitting the top
there that's why it's getting stuck so
why is it doing that I
think I mean it could be that the Top's
bent but I don't think it is I think
it's because this piston isn't pulling
in all the
way
let me should set this down and then you
can
see I think if I pull down on
this yeah see how the arm went down a
little
bit and it doesn't just free will it
actually the gear keeps turning and it
will put it in there it's just that's
where it's stopping because it's hitting
on the top so if I kind
of leave it how it is turn it back
on I got to see if maybe the the top of
the basket's bent or if that arm is just
not completely
retracting which could just be cuz it's
dirty and
things all right my assistant came in
Joe's telling me it needs oil now I'm
telling them that this stuff is like
fiber so I don't think it needs oil but
we did put oil on it to help clean it
oil is a cleaner too you know so we put
a little oil on it because the bow it
wasn't pulling in all the way now when I
looked at it where it's getting caught
is it's always getting caught with the
bow hitting the top right and so the way
the thing's designed I don't think the
basket can even turn when it's like that
now we do have a broken bow what do you
think Joe that could have been how it
broke but could been but I think if we
left it alone it probably would force it
in anyway because the gears are still
turning down
here right so it's still turning those
whenever I was able to Free Will it it
was because it was back a little bit it
hadn't gotten basically I had it turned
off if I would have turned it back on it
would have went around and grabbed that
gear and forced it down but the the main
problem was this isn't pulling in all
the way but it was filthy needed oil
Joey says it needed oil so I oiled it
okay so then it seems like it's working
better but then I noticed that it's not
playing the right side because of this
plunger here so this plunger pulls in
and depending on if this is on this side
or this side it makes the arm reverse
I'll show you that here in a second and
then so Joe said needed oil he said it
needed oil now why why why why did it
need oil cuz it was was stuck he said it
was stuck and it's old it ain't nobody
touched this thing in 40 years so I put
a little oil on the two pins now Joe p8
so this is what happens when you do p8
which is the BS
side didn't hold it long
enough there you
go all right here we
go so watch the direction of the
bow
Wham and Joe likes how it's very
forceful yeah okay so notice the bow is
on this side the reason for that is
because this little arm is out and it
hit it when it it goes by which forces
the bow one way or the other now if this
coil were to pull in it would pull that
pin in and pull that one out so the bow
would flip the other way okay now we've
been playing in8 over and over again and
it hasn't been doing that because it
wasn't right so I oiled it and uh we'll
see Joe go ahead and um move the uh arm
over and I'm going get ready to shut it
off in case
it gets
jammed see it went right in and then it
releases the record so if it hasn't
released the record yet it's not going
to allow the basket to turn which would
break the arm so I think we're all right
if we uh just watch that okay Joe now
play
in8 okay now watch this little arm
you'll see this pull in and move those
bam Wham which makes it throw it the
other way all right Joe hang it up one
last
time
Wham I think we're looking pretty good
now we're going to keep our eye on it
and look for other opportunities to make
it work better but we're waiting on a
needle and we've got other stuff to work
on so we uh looks like we've got our A
and B side working and it looks like
it's picking them up and it's hanging
them down what that is that I should say
pick it up and throwing them down Y and
then refiling them back in the basket
we're waiting on a needle and we still
need to mess with the I haven't even
touched the amplifier yet it's
unplugged now folks you've been watching
the video since the very beginning right
and we already did another video on it
this is our second video on
it and I had this problem with the
gripper bow and you didn't tell me what
the what the solution was it's right
here in front of it you didn't see
it we finally saw it cuz y'all wouldn't
help
us show them what it is
Joe the bands not down in the groove
there is a Groove the band is supposed
to be
in and it's off centered which means
that it's a little too
tight about died which means that it's
pulling this
down pulling this
down which is our whole problem the
band's not in the center so we got to
mess with it a little bit and get that
where it rides a little
better okay uh you got that side in over
there Joe so here go
ahead go
ahead he might lose a finger here go
ahead a guy that works with Donnie cut
two of his fingers fing off the other
day about got it bam there it
is
yeah that's better all right Joe what
number is
that N8 right I think so hit
in8 so that should give us just a little
bit more clearance on the top of the
bow and by the way it's called the
transfer arm I think but I like gripper
bow don't you like that better I think
that's what rockola called
him I didn't hear a scrape either on the
way out boys got plenty of room
now okay go ahead
to nothing to
it okay do it one more time and I'm
going to cancel I'm going to turn it off
right right when it gets to the
top so we can see the
clearance it's staying in our groove
where it's supposed to
be I don't know if I can do it on the
way down oh sh it's not even close
now that was the whole freaking thing
can you believe that mhm you saw earlier
it was touching right now it's not even
trying to
touch wow okay so I'll turn it off again
when it's trying to hang it up just to
make sure just push it over towards the
middle Joe you don't even have to lift
it up there you
go too
slow ain't it funny how one little
thing can cause that I wonder how that
got out of line I guess it just just
something that
happened okay so that's wow that'll make
it I feel a lot more confident about it
now cuz before I think we had it doing
pretty good but it was still it was real
close you know but this makes a lot more
sense very
cool all right now we found out one
other thing now Jo they're not going to
like this
I don't care it ain't that big of a deal
people it's not that big it's not that
big of you're going to be all right
people you you're going to be okay okay
you're going to be all right I probably
couldn't find that part anyway this we
probably couldn't find that part anyway
obsolete this is
obsolete 1964 people come on come on it
doesn't
matter okay so there's this little thing
here that tells you what records play
now right now it's in between I can fix
that but it's basically going to
say whatever right so right now it says
jk2 we are
actually on jnk2 okay so we're going to
get that where it's always lined up
right now there is supposed to be a
little assembly right here I thought
there was a little piece missing and I
was going to maybe fabricate it but the
whole thing's gone there are two coils
that go here and there is a little blade
that sticks out like over the k
and so if you if you pick
J2 one coil pulls in and moves the
little blade so that it looks like that
and then if you pick K2 the other coil
moves in and moves the blade so it looks
like that and so there's two coils and a
blade and four wires that are missing
someone has started parting this baby
out it's horrible what they did to it
now see those little wires there that's
where you connect the uh the little
jumpers to connect the the two coils so
they've removed that so on this
machine when it plays J2 it's going to
say jk2 now K is the other side of the
same
record when it plays K2 it's going to
say jk2 and J is the other side of the
same record I don't see the problem and
you just put in J2 look you remember J2
and K2 it's the same record so it's
playing that record you just got to
remember which side it's playing
come on people do we need to hold your
damn hand you can't look at that and
then look up here and then figure out if
it's playing chantilli lace or The Big
bers Wedding cut two completely
different songs
mhm you should be able to figure that
out and you you selected it and you
selected it I don't know why you're
arguing with us I don't know come people
it come come on people you just can't
make them happy I come on come on now
people if the if it's got the little it
doesn't matter why would it why would it
come on people it would why would it
matter people come on people it's
telling you the record it's just
not it it doesn't need to tell you the
side of the record you just you just
picked the record people I mean come on
now come on now you don't need that in
there you don't we don't need to buy
that you can't find it it's unattainable
we can't I mean I I don't know how to
use eBay all right folks so there you go
I think uh we're in a lot better
position now we still haven't got to the
amp yet
but that'll be another video I'm uh I'm
very happy though that we figured out
what was making that
jam uh that certainly would be a problem
right we've been cleaning it up a little
bit too working on the lights still got
another light that we have to get going
um we did a little paint on some of the
Chrome that was acting up that was
flaking just did some simple chrome
paint um
so a little bit farther to go on this
one still we still have to mess with the
amplifier I mean we got loose wires
hanging all over the place but you know
we kind of like to start at the
beginning so we got it
selecting we've got it picking up the
record we've got it hanging up the
record uh we're waiting on the needle
and the amplifier so it's getting there
everything uh is coming along nicely
once we learn what we're supposed to
actually be doing and how it's supposed
to be working so get yourself a manual
if you don't have one for yours and
it'll help you out tremendously so I
hope you enjoyed it so far make sure to
give us a thumbs up uh for taking the
trouble to film it for you hopefully if
you run into something similar on yours
this will help you with yours uh leave
your comments down below and make sure
to check out our brother's Channel my
brother Donnie the link is down below we
work on jukeboxes pinball machines
arcade games things like that he works
on Old buildings and cars and old trucks
and stuff like things of that nature uh
he's a little crazier than we are though
so go check him out if you haven't
already and we will see you on the next
video where we'll finally start working
on the
amplifier
