Thank you to everyone who has been supporting our channel! If you use the link below before you purchase anything on Amazon, we get a royalty for sending you there, thank you!
Our store is located at 139 Caldwell St., Rock Hill, SC 29730.
Ladies and gentlemen, this is Joe's Classic Video Games back with another cool pinball repair video
for you this evening. We are back here in the uh the bowery or whatever you want to call this room
where we keep all of our parts and work on some of our complete basket case pinball machines and
we've had this lost world here that we've been working on for quite a while. Now if you didn't
see the first video, this thing started out much worse. We put decals on it. We actually haven't
even finished that video yet, but you've probably already seen it. But before we finish that video,
we do them all ahead of time. Before we finish that video, I'm starting the second video because
I need to work on the power supply on this thing. My brother Joe is doing a lot of the cosmetic
stuff and I am doing some of the electrical stuff. So we've got to work on the power supply,
but here's the problem with the power supply. We don't have a power supply, so we've got to make
one. So over there in in all of our parts here, and a lot of these are monitors, but there's some
pinball parts over there. This is actually sorted very well. You may not be able to tell,
but there's some, you know, if you're an amateur, you wouldn't know that that's well sorted. But
you know, just me looking at it, I can tell that's some good piece of stuff over there.
I believe we have the parts to make the transformer part of the power supply.
The transformer block and the rectifier board are in this stash somewhere. So I'm going to see what
I can dig out so that we can put it in this lost world. You can buy a brand new transformer and
rectifier board assembly for these things. This is a 1970s Bally solid state pinball machine,
but they're like $300. 300 bucks! Now I've got parts. If I've got the parts,
we're going to cobble it together and make it work. I did this once before on a
Flight 2000 pinball machine that we had that somebody stole the transformer out of.
I mean, they probably owned it, so it probably wasn't really theft. They just borrowed it and
put it in another machine. Probably. I don't know. But a lot of times people part these out.
Drives me crazy. Drives me nuts. See all these parts? None of these parts are parts that we took
out of machines. These are all parts that I found somewhere and I'm trying to put them back in a
machine. I don't know why everybody does it backwards. They keep parting stuff out. I'm
trying to part it in. So we're trying to part this back together. If you didn't see the first video,
the bottom of this is a Bally lost world. Someone had parted it out and the freaking
head was missing. Right? So this head is the wrong head because the head is from a
stern stingray that we had that the body was missing from. So we're using two to make one.
So in the previous video, like I said, we did the artwork and things. Let's look inside of that head.
I can show you what we're missing. And again, if you saw the first video, you probably saw it a
little farther along than this because we haven't finished that video yet. Everything looks pretty
cool in here. We had to do some repair back there where the cabinet was a little beat up. But as you
can see, it's turning out pretty nice. We still got to put the rails on and clean them up. So this
was a stern stingray, right? Which means that this lamp baffle board is what I call it, but
whatever it's called, the lamp board is wrong. It won't be correct for the back glass that we need
to put on it. So this is what's left of the stern stingray. You can see that it's still got the
knocker coil up there. Now, why would I put a stern head on a Bally body? Because it'll work.
That's why. The stern games are copies of the Bally games. So it's wired very similarly,
pretty much the same, and it uses the same boards. So on a Bally or a stern, there is a transformer
that sits right here. So if I can find in my stash over here, one of these transformer blocks,
or if I can find... I just need to find the transformer, basically. I think I've got one.
Let me dig a little bit. But basically we're trying to create the part here, right? That's
the first thing that the power goes to, basically. The power comes in here, goes to this
line filter with a varistor across it, and then a couple lines run up here to a power switch
underneath the cabinet. So if you reach behind the front leg, you can turn the power on and all.
And once it does that, it travels back and goes up into the cabinet through this hole
and plugs into the power supply over here. Not that, this one. Plugs into the power supply.
So we've got... are we missing a part? Where is our third wire? That goes there.
That goes there. This is the power coming in. There's another one. Oh, it's the play field.
I don't have a play field in. Okay, yeah. I have to remind myself sometimes. Okay,
so I need to find that part. That's the next thing that we need to piece this thing back together.
And if we don't have it, we'll order it. But I'd love to not spend $300 on just the power supply
inside of it. Well, as luck would have it, I do have a transformer. I thought I had one.
We did one previously, like I said, on that Flight 2000. And I think I used one that originally
had been in a Bally Dolly Parton machine. I think it was marked on it that it was for
a Dolly Parton. And we figured out that it would work in the Stern Flight 2000. This appears to be
a Stern transformer, but it would be for this same era of game and it'll work just fine.
You can kind of tell. I don't know how much you're going to be able to read that.
Can you tell that it says 16B3? Right, 16B-3. 16B3. And then down below it, it says 37- and
then I think that says 7838, if that's what that says. The 7838 is a date code. It's the 38th week
of 1978. So 16B3. This is actually a Stern transformer, which would have been exactly
what is in our Stern head. Okay. And then I found this. Now, this is the little plate
that mounts in the back. The transformer mounts right here. Right. And this big heavy plate
mounts in the back in that corner. And that's the transformer assembly that we need.
Suspiciously, this is also a Stern. The Bally ones look exactly like this,
but this is actually a Stern. And that's a Stern. The wires are cut off this and the wires are
missing from this. So we probably picked this up from some some place and they had taken this.
Originally, it was screwed right here. It's probably the same setup, right? And somebody,
for whatever reason, took it all apart and then didn't do anything with it. And now I got to put
it all back together. I don't know why people do that. This is what I'm talking about. Why in the
world would you part it out and then not use it? I mean, I can understand stealing this because
you got to put it in some other machine. I wouldn't do it. But if you got to do it, you got
to do it. But why take it out and just set it somewhere? It doesn't make any sense whatsoever.
Why would you take this and cut all the wires off of it to where I got to put them all back?
I want you people to find out who did this and then we're going to come get them. That's right.
We're going to get you. All right. So there's a bunch of wires that go from here onto the back
of this board. And once it's complete, basically this board handles all the connections. So that
one little plug from the cabinet plugs in, I think, here. Here or here? One of the two. We'll
figure it out. It can only go one way. It plugs in here and then the other one goes out to the
play field and the other one goes into the back box. So the AC voltage comes out, runs through
one of these fuses. So it runs into a connector, runs through a fuse and then is hardwired on the
back to this transformer. The transformer transforms that wall voltage, which in our case
will be 120 volts, into a bunch of other voltages. Those voltages are sent out of these lugs back
into this board through wiring that's soldered on the back. You'll see all that here in a minute.
And the wiring runs through more fuses and runs through bridge rectifiers and through resistors
and all this stuff. And then once those voltages are rectified at a DC or one of them's left AC,
or a couple of them, no, one of them's left AC, once that happens they're sent back out
through these connectors to the play field and the back box. And so it's just a really
convenient way for them to create with this transformer all of the voltages that the
machine needs to run. So it needs a, you know, 120 volts goes in but the only thing in the game
that uses 120 volts is this transformer. And so the transformer then creates separate voltages
on these separate taps. So one of the voltages is like 43 volts that it uses to make all the
solenoids work. The coils need 43 volts. One of the other voltages is 12 volts that's used for
some things and then the 12 volts is used on another board to create the 5 volts that
runs all of the IC chips in the game. It's all digital of course, solid state.
There is a 6 volt voltage DC that is used to run all of the lamps in the game that are turned on
and off by the computer. And then there is a 6 volt AC voltage that is used to run all of the
general illumination lamps in the game that don't get switched on and off by the computer.
So basically there are a bunch of bulbs that are always lit just so it you can see general
illumination. And then there's a bunch of volts that are computer controlled bulbs, not volts,
bulbs. And then finally there is a voltage of 220 volts that is sent up to the
solenoid driver board to create the voltage for the displays.
They're calling me. They've got to have me. So one of our problems is when they took this
apart, they lost the little part, the little piece. This is another reason I don't like it
when people part stuff out because you lose parts. Leave it where it is, right? So they
took this board loose so that they could cut all the wires off and then whenever they did that,
they lost the little heat sink that goes there and the three screws that hold this to the heat
sink. So the way this was originally designed by Bally and then copied by Stern, this is a Stern,
is these three bridge rectifiers are used to create DC voltages that get used in the machine.
Now remember the transformer doesn't rectify anything. All it does is it takes AC voltage
and it transforms it to other AC voltages, right? So once it sends it up to here,
those three bridge rectifiers rectify the voltage to make DC voltages.
And you can see there's a space between those three bridge rectifiers which are all in a line
and the actual plate. I've got it exaggerated right now, but there's a little space there.
And there is a little plate that goes in between all three of those and this plate
that acts like a heat sink. So you can see where it was, you know, you can see that there was a
big square bar right there. And then there were three screws that go through the top
that go through those three tapped holes and hold it down. So there's a couple ways we can
fix this. We could make another plate. I was planning on doing that, but I think I'm gonna
do something else. You could make another plate basically to replace that, right? But the problem
is these are slightly undersized in the first place. It wasn't the greatest design to begin
with. These, sometimes these will burn up and they're old and they're probably a ticking time
bomb. So we might get rid of those and change it, right? Because it would kill two birds,
one stone. So I was going to do that. You could also probably take a like a nut from a leg leveler
or something, you know, some kind of like a nut, put one on each one, put three screws in it. We
probably find screws that'll fit. And the nut would connect that to that, but you're not going
to get the best heat thermal dissipation that way. People that actually know about, and I'm not one
of them, but people that actually know about this being a heat sink and know about the whole thermal
properties of it and are big sticklers for that, they would go crazy if you put just a little
round circle to transfer the heat from the bridge rectifier to this. So I don't want to do that on
tape. So anyway, these things get really hot. And so that bar is so that they would be thermally
connected to this plate and this whole thing would act as a heat fin and it would radiate
heat off of it. So instead of this being 140 degrees, since it's connected to this and it
starts heating this up, this whole thing's 95 degrees, you know, and everything's lower.
It wouldn't get that hot, but you get my point. It basically, by spreading it out with more surface
temperature, I mean surface area that's exposed to the air, it'll cool down and keep this from
being 145 degrees. If you run it with no heat sink, you run into problems. But there's a thing you can
do. We could remove these three and mount them on the top. That says plus, minus, AC, AC. It doesn't
say AC, but the two that aren't marked on each one are AC. You can actually mount them on the top.
It's a little harder because we're going to use bigger ones. And then you can use like 35 amp.
These are, I think, 8 amp. You can use 35 amp bridge rectifiers. They run cooler because they're
designed to handle 35 amps and you're only running 8 amps or 7 amps or 6 amps or whatever
through it. So they don't really overheat. Now you could even mount heat sinks on top of those
and everything else. But I think you'd probably be fine just mounting the three open-faced
bridge rectifiers up in the air where they could just dissipate the heat on their own because
you're never going to get them anywhere near their working capacity of 35 amps. So I think
that's what we'll do. And then that way we don't even need the screws that go in it. We don't need
that little bar because we won't be using this as a heat sink. We'll just be using it as a way to
mount this board. So the first thing I need to do is find some wiring so I can connect this transformer
to all of the little spots on the back where the wires were. So see like that is a solder joint
right where they just cut the wire off. So I need to put a new wire in there and then run it to
whatever tap over here that it's supposed to be. The chance of screwing this up is through the freaking
roof, right? Which is another reason they never should have done this. It would be really easy to screw
this up and get one of them that's supposed to be here connected there. And you could blow fuses,
burn up this board, melt down part of the transformer. Why are they doing me like this?
Once we get it all done, this was laying in the bottom of the of the machine. That is the guard
that mounts around that thing in the back box so that you don't touch the high voltage and get
screwed up. Right, so let me find some wire and yeah we'll see if we can just rig it up
professionally the proper way. Fortunately in the bottom of the cabinet and this thing has been
horribly abused but in the bottom of the cabinet the original manual was in it and more importantly
the original schematic package even. So this is how the transformer assembly was set up and this is
the bally stuff but again the stern is pretty much exact. This is how the lost world was
originally set up. Now the first thing we're going to do is there is actually a set of jumpers
here on the input of the transformer that changes the input line voltage. So if you look this one
has 1 and 3 connected and 9 and 11 connected. Okay 1 and 3 and 9 and 11. That means it's set
up for 115 volt line wall voltage. So we're going to change that just a little bit because in reality
over the years they have raised the line voltage everywhere. Right, so we're way up over 120 now.
Usually when I check it was like 125, 126 something like that but they only have a
provision for 115, 120, 220 and 240. So we're going to set up for 120 and the way you do that is you
you tie 1 and 3 together and 5 and 7 together instead of 1 and 3 and 9 and 11 and then you
hook power to position 1 and position 5. All right so they are actually showing that here the power
is coming in at 1 and 5 and they're saying that if you hook it up for 120, 1 and 3 should be
connected and 5 and 7 should be connected. Right, so they're showing you how they want it hooked up
for 120 but again this is a stern. This isn't out of this actual machine and I guess at the
time stern was hooking theirs up for 115. Look at this. Do not like that.
I don't like that. So that is the wax that's inside of the transformer.
When a transformer gets really hot, one of the things it does before it burns up is it it melts
down and you start seeing this. You'll see wax puddled underneath it. So we may end up in a
situation where this thing is shlonged. If you see a little bit of it, usually it doesn't
necessarily mean that the thing is shorted but it means that it got hot. So it's possible to see
this and the thing still be fine but that's what that is. That's wax that has leaked out of that
because it got so hot that it liquefied and started leaking out of the transformer.
If the transformer got so hot that the coating melted off of the wiring,
then somewhere in here the wires, bare wires, will be touching each other and the transformer
won't work properly anymore and it'll be junk. Right, so hopefully we're not going to see that.
Just that one little bit that came out, that's probably all right. It probably just got hot as
crap and leaked out. It could have even been stored somewhere where the temperature was really
hot and it leaked out. It's literally wax like from a candle, right, so it doesn't take a lot
to melt it. But I still don't like to see that. So anyway, I'm gonna fix those two jumpers and
that's step one. All right, so the wax was back here. It doesn't, that doesn't really mean anything
but I mean it, that doesn't, the location isn't all that significant because the wires wrap all
through there. But there's another piece up here we're going to look at. Okay, so one and three is
still connected. I didn't do that. I added a jumper to five and seven and then I removed the jumper
from nine and eleven because we're not using it. It probably doesn't matter if you leave it hooked up
but it might, so I don't, you know. So there was a strong wire connecting those together
and I've cut it loose so this one does not touch this one now.
All right, okay, so that's good. So we're set up for 120. Look at this. There's a little more wax right here.
A little bit here, a little bit here. Now you see how much is wrapped in there. I don't know that
you can tell. Like I was thinking, well since it's there maybe we could look at this. Maybe we could
figure out what that line is and see that that overheated. But I don't think you can do that
because I think it's, they're all wrapped around in there so many times any of them are probably
going through there. So we don't know which one got hot. I'm a fairly lucky person if I don't
jinx myself here. So usually luck breaks well for me. So I'm going to guess that this thing's still
fine, but we'll see. All right, so first thing we got to do is start hooking up some of the wiring
back where it goes. Now how do you do that? Well it shows it very clearly on here. So we just did
this side. We just haven't hooked up the two wires yet, right. So the wire that runs from number one
hooks to E2 on the board. E2. Et tu, brute? Um, where is E2? There it is.
E2. So we need to clean that up, but that's where that wire would go, right. And it's soldered on
the back. Are y'all getting scared? I'm not scared. So that white wire there was originally one of the
AC wires. And every one of them is labeled like that. So I'm going to add a few of them back in
and we'll go from there. All right, so I went ahead and put all of the wires on it.
Going to every single test point. There's 12 of them, not test points. E10, E11. I wonder what
the E stands for? Probably makes some kind of sense. So it works pretty intelligently really.
It looks like a big mess, but really if you look at it, 11 and 12 are a pair. So one of them runs
here, goes through the fuse, goes to the bridge rectifier, and then the other side of the bridge
rectifier, rectifier 12 connects to it, right. And so one of them is 9 and 10. So 9 connects here,
runs through the fuse, goes to the bridge rectifier, and on the other side of the bridge rectifier,
10 connects. It's the two AC inputs to the bridge rectifier. One of them is 7 and 8.
So 7 connects here, runs through the fuse, and then there is a little, um, oh yeah, that's the,
that's the lamp one. So the 8 is connected over here, which is on this big huge ground.
That one's an interesting one. If you look at the schematics, you know, you got to think about wire
gauge. I'm using as heavy as I can get through the holes basically. Um, on this, you're running
three amps through it before you blow the fuse. So this wire only needs to carry three amps. That's
the main line into the game too, the AC line, right. But on the other side of that bridge,
you've actually, I mean on the other side of the transformer, you've actually got a 20 amp
fuse on the general illumination, because there's a ton of lamps on there, right. So it's a lot of
amperage. So because of that, they have drawn it, and I love this kind of crap, because it's,
you can tell what they're saying. Look how they've drawn those two lines with an extra line.
Why are they doing that? Because they're telling you, hey, there's 20 amps here,
you might want to beef that up, right. So that's E7 and E8. If you look at E7,
it's right there. There is actually another provision for a second wire beside it. So you
could run two wires back to your lug. It wasn't like that from the factory though. There were
not two wires though. And then E8 is over here on the ground, or maybe that's not the ground.
Is that the ground? Yes, that's the ground. E8 is over here on the ground, and there are also,
there is a provision for two wires there too. So you could double that lineup if you wanted,
but it's not like that from the factory, at least on this stern. Okay. So I've got them all in.
We're going to do a whole bunch of more updates to this board, but I think I'm going to test it
first just to see what we're messing with. And if there's anything wrong with the actual rectifier
board, it'd be good to know that before we start messing with things. Now, if you'll notice,
there are test points, but they're past the bridge rectifier and they're past the fuses.
So if a fuse is not present, these test points won't work. All right. So I've got to get all
the fuses right first, but we're going to put it in the cabinet and see if we've got all of
our voltages or if something's going to burn up or blow up, or if the transformer has melted down
in the past. So what do you think? Is the transformer screwed up and that's why they took it
out of the machine? I don't think it is. I think they just took it out of the machine. All right,
folks. So Joey was able to make me the little spacer. It's just a piece of aluminum with some
holes drilled in it. That's exactly what the original one looked like. It's slightly thinner
than the original one, but this board has a little bit of flex in it and that won't be a problem.
I've seen these before where people mounted them without the spacer and just screwed it down so
tight that the bridge has touched the plate. That's not a great idea. So you can see the space there.
You can see the three holes below it. Another problem we have though is we don't have the
correct screws. I'm going to use these, maybe with some nuts on the back. But the problem with that
is you've got to be very careful that they're not touching any of those four pads around it
or it will short that to ground. So these originally had a little nylon spacer that
went right under the head just for that so that the head wouldn't touch any of those four.
Ironically, it kind of almost seems like it's touching this pad, which is the ground,
which would be fine. But we're still going to do it. Okay. Whoa. All right. So I tested the bridges.
They seem fine. I tested the fuses. They're all fine. And I made sure that they are the right
value. A lot of times you'll see these and the fuse will be the wrong one. I tested these diodes
and they're fine. I'm going to replace these though, but we're just testing it for now.
I checked this nice resistor. It's fine. I checked this resistor. It's fine. Look at this beautiful
resistor here. Those are those cool old ones. Look at that. Look at that bad boy. They look
like a Tootsie Roll Pop. So yeah, there's really not much to the board. There's the connections.
I didn't re-solder these yet. We'll do that later because all I want to do is plug in the one
connector and then test our five test point voltages. And that will tell us if the transformer
is cooked or not. I put some zip ties on the wires. And then once it's mounted in there,
this thing goes like this and covers all of that up. So I think we're looking pretty good. So we're
going to slide it in the game and we're going to try to turn it on the power and see if we
burn anything up. And if we do, we'll fix it. All right, folks. So I have the pinball machine
plugged into the wall. I've turned the power supply around and all I have plugged in is that
one connector. Okay, let me show you. Let me show you something. So this connector is the one that
comes from the bottom. We're plugged into the wall, but we're turned off. However, there's a
little bit of voltage on there. I don't even have, I've just got the one probe hooked up, right?
That's ghost voltage, I guess, by the meter. I guess that's just how they work. So the very
first voltage is actually a DC voltage. And the ground on these boards is this trace around the
outside. So you can touch at the bottom of this resistor that's connected to ground. There was a
big old solder pad right here where that one wire was that we were looking at that can be doubled up.
So we are turned off. We have zero volts DC. I'm going to try to turn that on.
I think I'll step back a little bit just in case it pops a fuse or does something crazy.
It seems all right. I can actually hear the transformer just barely. I won't be able to
record it where you can hear it, but there is a very low hum, which sounds good. It doesn't
sound like it's messed up or anything. Our wax was over here. Yeah, everything seems cool.
So let's see. So test point one, let's see what we get there. DC voltage, 5.9 volts. Very cool.
So that's the DC voltage that they used to turn on all the computer controlled
lamps. So we'll move over to test point two. Very cool. 181 volts. That is the voltage for the
display. Now that should be like 230 or 240, but it's low if you don't have anything else plugged
in because there's a, and this is DC voltage, there's a capacitor up on the solenoid driver
board where that power goes. Ironically, we're going to regulate it back down to like 180 volts
on that board, but it's working just fine. That'll rise up to like 240 once you plug that board in.
So that's good. Test point three, 13 volts. Perfect. That is the 12 volt, unregulated 12
volt DC that gets turned into five volts, uh, up on the solenoid driver board. And then that five
volts is used to run, uh, all of the IC chips on all of the boards. They also use the 12 volts for
some things like the led on the MPU board and stuff like that. So, uh, but the 12 volts is
unregulated. So it's 13. All of these voltages will be a little high, but in the case of the
displays, it's actually a little low. It's just one of those things where it makes sense that
they're off. You're not looking for them to be exactly on the money. You're just looking for
them to be there or be way off. If they're way off, something's going on. Test point four, we'll
skip because it's AC. Test point five is also DC, 43 volts. So that's the, uh, solenoid voltage.
And it's about right on the money. I think it's supposed to be 43 volts, 42 or 43, but I think
it's 43. Um, very cool. So we'll switch over to AC and then test, test point four, 7.1 volts.
That's supposed to be 6.3. That's for the general illumination, uh, all of the lamps underneath the
plastics and on the back box and all of that. So it's a little high because there's no load. We
in. So if we had the coin door on the machine, the coin door bulbs would likely be turned on
right now. So in other words, transformer works just fine. So we've got a good transformer.
We're going to work on the rectifier board. This board's called the rectifier board.
We're going to work on that just a little bit more just to make sure that everything's reliable.
So let me, I'm going to pull it back out to where we can mess with that just a little bit more.
So the first thing that we're going to do is on this schematic, if you look,
this bridge rectifier that's created here by these four individual diodes is to create the voltage
for the displays, 230 volts. So instead of using a bridge rectifier, they use discrete diodes
because I guess because of the higher voltage, right? So these are problematic. They'll fry
every once in a while. So I've seen many times where those have went bye-bye. One of these had
already been replaced some time in antiquity, right? So I've popped all of them out and I'm
going to put new ones in. They originally were one in 4004s. You can use, you know, one in 4001
to, I don't know about one. Don't use one. You can use four, five, six, or seven for sure.
Okay, so I put in four new ones. Everything seems good. The last thing we're going to do
is we're going to re-solder all of these little connectors.
Basically these get bad solder joints on the end where they break loose from the board from people
moving them around. Someone has already worked on this. Notice they put this jumper here.
If you look, they are jumpering from these two pins to the second pin over here.
So that just, I'm sorry, the first pin over here. So just think of the first pin there,
right? See that trace? They're mimicking one of those traces. That's got to be that one.
So they're going from there over to there. Let's see if that's correct.
I didn't put that wire on there.
Boy, this is a bunch of junk here, isn't it? Yes, yes. See the first pin there? They have
connected to the first pin there. So basically they are making this connection that's on this
side of the board on the back side as well just to make sure that all of that's connected well.
So that's J2 pin 1 and J1 pin 8. J1 pin 8 and J2 pin 1. So it's the general illumination bus
and the general illumination bus. So they, on the schematics, they have them drawn where they're
connected back here. There is a trace running from there to there on the top of the board. It
just happens to be how the board's laid out. So they've just put a jumper to make sure that that
connection is good. So nothing wrong with that. Okay, so I'm going to re-solder all of those
connections on the back and then we'll be ready to mount this plate. I found some little insulator
things that look like they may have came off something just like that that I was able to put
under. I used some different screws. I was able to put under the screw head and it is all
sandwiched up in there. I put some more heat thermal grease, you know, zinc
gooey stuff on it. It's all good. So two will do you. If I had a third one just like that I'd put
in there but you don't need three. Come on, people, come on. There's one here and one here.
You don't need three. I was overkill. They were just doing that because they could but you don't
have to. You don't have to. Come on, people. You don't need three of them. If you ain't got three
you could use two. Now one, one wouldn't work because it would hang, you know, but maybe if
you put it in the middle and then real, but you don't want to do that. Probably two would be
better. Let's be honest, three would be better, but I don't have three. All I've got is two.
Come on, people. That's just as good as it's going to get. All right, don't worry about it.
Okay, so I cleaned up this area a little bit and mounted the thing in there. Now it mounts slightly
different than the one that was in there. Some of the sterns had a little u-shaped metal basket
that it sat in down here and then the plate mounted separately up here. So because of that
I had to mount it just slightly different and because of that I put the guard on here,
but I put it upside down on purpose because there's a, see the little cut here? That is
supposed to be down here. I made another one over here because if I had it the right way,
the way this is mounted, it pushed this back far enough that it was almost touching those
the lugs on the transformer. So you don't want that. You want plenty of space all the way around
it where it won't shorten anything out, which means this is out a little farther. So it's on
this brace here, but that's fine. That brace is just to stop this, right? So everything's cool
and it's not flush with the brace. It's back. So everything's cool and I put the original
little head gear back on it and that's so that you don't touch the,
that's so you can do this and not get shocked, right? So now here is the most important part
of the whole video. Are you ready? Are you ready? Now we need to see if the pinball machine wants
to cooperate. Now these are inanimate objects, but they were made by humans. Humans built this.
They have the time and the heart that the humans put into it to build these things and they're
still doing it today. Stern Pinball is still making pinball machines. Jersey Jack Pinball
Company is still making pinball machines. Spooky Pinball is still making pinball machines. There's
several other companies as well. So there's a, it takes a lot of time to build one of these, right?
So like I said, it's an inanimate object, so it can't do it itself, but they kind of help you,
you know? So whenever this thing was designed, one of the things they designed was for all of
these little beautiful light bulbs on the back box to come on just as soon as you turned it on.
And we fixed the power supply. We saw that the voltage is there. These are some old looking
bulbs, right? But maybe if we're lucky, maybe it'll decide to cooperate. We've done what we
can to fix it so far. It needs to help us a little bit. So let's see if one bulb is still hanging on.
What do you think? Fantastic! Now, that's the wrong lamp board because this is out of a sea,
not sea witch, the other stingray. It's out of a stingray. And so the stuff needs to be in a
different position for Lost World. But as you can see, it's trying to do its part. At least the
light bulbs are working. Now, most light bulbs will light up if you run juice through them, so
it's not a huge accomplishment, but at least it's trying to help us. So with its help
and your help coming back and watching on the next video, we'll get a little bit farther. So
we'll see you on the next one. Hey, by the way, if you're not tired of watching us work on
a Bally Lost World, check out this video and we'll see you here in a couple days.