Timber Framed Barn Part 11 Cross Frames And Oak Pegs

Nature house
149 followers
#NaturalHouse, #EcoHome, #SustainableLiving, #GreenArchitecture, #EcoFriendlyHome, #OrganicLiving, #NaturalLiving, #EarthFriendly, #EcoDesign, #HealthyHome, #GreenLiving, #SustainableHome, #NatureInspired, #EcoHouse, #EnvironmentallyFriendly
Right, good morning everyone. It's Monday morning, new week for us. So I wasn't here Friday,
I was sorting out the video editing. The guys got another cross frame started.
They got it to the point where it's ready to scribe and have braces. They scribed it this morning.
So Nye's just cleaning up mortises. Howard and Steve are... Howard's boring mortises,
Steve's cutting out tenons on braces and I'm cutting out some more braces ready for the next
frame. So it's gonna be a busy, busy week. We've just got to work on these cross frames but we're
gonna run out of timber by the end of the week so we're gonna have to stop for a week for me
to catch up with Millen. But that's all good, the boys are happy to do that. So yeah, we should have
this frame done today and then we'll start another one. Oh yeah, also, I've also bought the feet
and we're gonna get these feet put on as well. So last night I surveyed the site,
my foundation pads and essentially we're gonna cut all the posts to the right lengths because
obviously all the different pads are at slightly different heights. So I've surveyed it and we're
gonna cut all the posts to the exact height they need to be so it all sits level and then we'll
mount the feet as well. So when we put it together it'll just sit right straight away.
This one here is the lowest one which I've used as a reference. So everything else is,
so that one's sitting 20 millimetres higher than this one. The biggest deviation is 51 millimetres
here. Obviously these ones are taller anyway. So yeah, we've got all the information now we need
to cut all the post lengths to exactly the right size. So yeah, it didn't do too bad a job. This
one's the biggest difference at 51. That one's just a bit too high, but all the others are quite
reasonably close really.
Up there and then one more. Yeah, better check with references.
Right, we're gonna have a go at mounting a foot to this post. So we just need to square it off
a little bit and then yeah, see about getting one that's got to sit in a slot. Yeah, it's gonna be
a bit of a faff to be honest, but we'll get it. These are the slots that the feet are going to sit
in. That's the plan. Right, so these are relatively time consuming, but I've got it sat on there.
I haven't quite got it centred perfectly, but it's not too bad really for a first go at it.
That's where it'll sit there. It's just my holes are a little bit off centre,
but I'll get better at them. Yeah, let's do another one. 19 to do.
Right, so that frame's done, ready to go and I've just mounted that footplate. Howard's doing
another one over there. I'm going to start another one here and while we're doing that, Steve has
started doing the truss for the next end frame. As always, you just leave Steve in the corner
quiet and then you come back and loads of work's been done. He's the main man.
All right, we've just fitted the last of these feet for this frame.
So me and Howard are both doing that while I and Steve are working on the truss.
So this frame and the frame we did last week is now ready to go, packed up, go back to my place.
So we're going to pack all this up, stack it and I think I'm probably going to carry on fitting
feet to the other posts we got and then we're going to start doing the other end frame,
Me and Nye are getting the purling housings
on the rafters of the truss which is going to sit on that gable end frame.
All right, finished doing those notches, housings. So the guys are just starting doing mortises
and slots and just yeah getting on quick as anything. I've got to go and do boring accounting
stuff annoyingly. So yeah, I'm going to have to come back tomorrow. Yeah, carry on tomorrow.
Morning everyone, so just about to head off to the barn and before I do that I'm just going to go and
put the sheep and the lambs on the reseeded field. They're all sort of ready to go out together now
so we're going to go and put them out all together. Sheep and lambs all on the same field,
lovely bit of grazing for them so it should be a nice little thing to do because they'll be
really happy out there. So go and do that. As you can see we've got pegs showed up,
had these made. We're going to come back to that later because they're not up to scratch.
So yeah, off to put the sheep out, off to the barn framing, we'll come back to these.
All right, let's get these out on a nice bit of fresh reseeded pasture. Come on in, come on in.
First time they're going out on a nice bit of luscious ground.
Right here everyone, new day, well after break on a new day actually. This joinery's done,
this frame's laid up and the guys are just starting to scribe the braces, fit the braces,
scribe them. So this is the other gable end, this is a front wall gable end. So this is one going
to have a fancy bit up to the truss as well like the other one. They're doing that and I'm over in
the corner mounting feet bases, post bases. So just got that one done. They're quite tricky to
do and time consuming so it's a good job for me to do really. Time for a fit up. So guys have just
cut out all the braces and mortises, let's now see if it all fits together.
There we go, ah there we go.
We'll probably have to do that strap thing back down to there again.
Right we probably won't have to do this one will we because it's podgered but maybe we need to pull it down.
Nice.
This needs lifting, it's lost its packers I think. Yeah and I'm stood on it, needs to come to us.
So that's another frame done then. So they're going to level all that up now
and then start fitting this middle post and then we'll have to get the truss together
and then scribe the truss in and it shouldn't actually be long before this is done. We'll
start laying up another one. Two more to go after this one but they're just middle frames,
not as complicated as an end one. And I'm still pushing on with the post bases over in the corner
These are really time consuming but they're worth the effort because when we drill,
yeah they're worth the effort because it's going to mount this building so
firmly to those foundations and it's a very windy location so
it's going to give me lots of confidence.
There we go, that one's done. So until I get the proper bolts, we're just poking these bolts
through. Should I do it from the other side? Yeah and then eventually I'll get the proper ones,
this will all bolt together, squeeze all this together, all mounted hard to the foundation,
can't go wrong. Right it's getting late in the day, Howard and I are just starting to,
well they've just scribed up the post into truss tie beam and so we'll be working on that.
Tomorrow there's braces still and everything to fit to that and a bit of messing around.
I'm going to get the other three post bases fitted to these while they do that and then
tomorrow this frame, another gable end frame will be done and then we'll start on the next one
which doesn't have all that intricate stuff involved in it, just the truss.
All right back from the barn and I've got to have a proper look at these pegs.
As soon as I took them out of the box I could see that they weren't up to scratch.
Now I'm looking at them closer, I'm even more disappointed by them.
So normally I'd make these myself, I really like making them but you need straight grained oak
and you know I needed 600 for this building and being as busy as I am at the moment thought it'd
be a better idea since I don't have the material anyway just to get a timber framing company to
make them. I'm not going to name the company because the person has been reasonable about
it and I've got some money back because of the bad quality. But yeah they're pretty bad
and I have to go through every single one of them now and change them all, show you the problems.
So first thing is just how poor the quality is. I mean there's a couple, I mean that is really
really poor. I mean there's some real belters in there like paid £1.50 each for these. I mean look
at that, it's split and that's that's firewood. I mean look that one knotted, can't use that.
Yeah like these, yeah crap. They're all supposed to be 330 millimetres long,
I'll get a tape. They're all supposed to be 330 millimetres which those ones are.
That one there's 290. I've got one here that's 250. So if that's in a 200 millimetre piece of
which it is, it won't even have sort of 20mm stuck at the end maybe. Some of the bits of
wood are 210. You can see that, sorry. Yeah so and there's quite a few, there's whole bundles here
that are too short. Like that whole bundle is too short. It's supposed to be 330, 280, 280,
too short. They've also been made by different people. So there's these style, that's a bit of
a better bundle really. There's those style but then there's these ones have been made
completely differently. So you see those ones are sort of right and then there's these ones
who've not really had any taper given to them and just been made the point really tiny.
There's no consistency to them. They're not well done at all. The real shock is over here. I mean
how did that end up in the pile? I paid £1.50 for that. I did get a bit of money back like I say but
I mean look, that's firewood. Look at that. What is that? What craftsman would be happy
to send that out to hold a building together? I mean look at that. That is a real beauty isn't
it of a peg. It's a natural product but that when you split it, it doesn't split right. It's got a
knot in it. It goes in the bin in the firewood. That's the end of it. That's the end of the peg.
That's the point. A big flat spot in it and the end's knackered. Yeah that's what I'm dealing
with. So yeah not only do they look really bad, the quality's poor. Another one with a big knot
in the middle of it. Right where it has to interact with the tenon. But not only do they look
really poor, they're also just not fit for purpose at all and I'm gonna have to redo every single one
of them. Let's say for example we take this pack that looks all right. Right length and everything.
£1.50 each and let's say we're putting the building up today.
Drag a big piece of you know a whole frame up. Everything's sort of there waiting to go.
Need to bang a peg in. Go to bang the peg in into a 19mm hole which is what we've got here.
Go to bang it in. Fine, fine, fine, fine, fine. It won't go in. If I bang that in to where it
needs to be, you know they're not long enough for that to be all the stick out because we're
not even enough all the way through the wood yet you see. It's a 200mm piece of timber that's only
just sticking out now so that needs to come through a lot more yet out the side and if I
was to bang that in. Bang, bang, bang. It's going to split this bit of wood because the end of it
is so much bigger than a 19mm hole. So I've got this one is saveable if I take this end down
to 19mm so it'll drive all the way through. Another one that you can see it in them.
They've got a big bulbous end on them so you go to bang it in on site putting the frame up
it stops. It stops and won't go in. Some of them are ridiculous they're just way too big like some
of these ones that have been made by a different person. They won't go in at all but that's that's
the limit. It's got a big split down it you know that won't go in it will just split the timber
out. You know pick some other ones there's that beauty there you know they're supposed to go
through a 19mm hole some of them don't even go in a third of the way. If I find a beauty
there you go look at that what's that supposed to do you know it will drive in it will drive in
but it will split that piece of timber out.
So I've got to go through and modify every single one of them now on the shave horse
try and get them so I can use them. So over the years I've learned that you can't trust people
to do good work you just can't do it. So before I ordered 600 pegs I bought a sample pack here's
these are what they sent they're great they're right that's how they should be.
Put it in a 19mm hole it goes down to there that last little bit will tap in won't take much force
yeah that's correct yeah it should really fit through the hole but that you know that's
completely passable. Those are what I ordered I've got 600 of something completely different
made by two or three different people. So yeah now we've got to modify every single one of them
so we take one of these pegs with a big bulbous end on it try it in a hole we can see that that's
not gonna pound in if it does it's gonna split the bit of wood because it's got this massive
fat end on it and then put it on the shave horse take that end down so it'll fit
in a 19mm hole without getting jammed up because if you get these jammed up
there's really no getting them back out again you have to try and drill them out
they're an offset hole so you can't just drill through so you have to sort of drill from both
sides without damaging the hole and you know you could be there an hour trying to get one of these
back out the nightmare I've done it you have to make sure they they're not going to do that
there we go that's more like it I'm fitting that hole better now wouldn't get jammed up won't split
stuff so I'll do that 600 times but don't fancy doing that 600 times because that's going to take
forever so I'm going to go and make a tool to do it so that they're it's faster easier
and they're all consistent because if I make a tool I know for a fact they're not going to get
right size hole this end and uh we've got a too small hole now here so I just need to bore this
out wider to about here maybe so that when we drive the peg through it's not going to get stuck
in there so obviously if the hole is the right size all the way through this length it's going
to be too much force to get it through so just bore this back now oversized it's about here
that'd be perfect there we go one die made so now I can just drive the pegs through that and it
should take them to the right size which is what should have been done from the start when they
made them really I haven't tried to make that really nice so it's just rough this is all it
needs to be all right so just give it a try before we get it all properly set up here's one of the
pegs with a big stumpy end that never work see it just get jammed in that hole let me drive that
through and then you've got to put another one behind it to get that first one out oh hitting
the bottom of your vise there we go and now that is shaved to the right size hasn't got a taper on
that bit but um that won't matter because from there back it won't actually be interacting with
the join I just want it to not split out that hole that it's getting driven into but now it's the
right size for that it won't split that out so what you should do when making pegs is you should
run the blanks through a die first and then taper them so that they're the right size to start with
but I can't do that now because someone's already you know done that so we'll just have to uh
make them good you know there's significant amounts come off them that is enough to get
that peg really jammed up in there that one would have been okay yeah what they come out as
after going through there is more what we need cool the final check here is I've drilled this
19 mil hole really close to the edge in a thin bit of wood so if we can drive that all the way
through there without it splitting we won't get any splitting issues when we come to it
that's what we want perfect that is exactly what we want drive one of the ones that hasn't been
put through the die yet make sure we miss the vice drive that through there
that's the issue yeah so yeah that was a project worthwhile so I just got to drive 600 of them
through that and then we'll be good and next time do the job yourself right morning everyone
another day and uh Howard, Steve and Nye are just gonna get this laid out ready to put the braces in
two braces for the uh for the truss down to the post and while they're doing that I'm gonna get
the three uh post bases mounted to these and then sort of by lunchtime one o'clock this frame will
be done ready to put put in the stack ready to go back ready to go up all right assembly time
right gently gently though because uh
don't really want to get in somewhere but give it a measure
let's just check this diagonal again in case we wobble it
the best technique I've found for these is to uh drill all the way through try and find the
hole for the bracket and then just keep drilling until you almost get out the other side
there we go I can feel that just coming through there
so I'm through the plate now through the hole that's lined up
I'm gonna take that out it does uh does wreck your bit a little bit not too bad
and you countersink that up the side and I can get a piece of a 16 millimeter stud in
to find that hole okay and then I've got to try and drill through again to find the other hole
okay
all right money shot
we won't go up there because we're in
okay cool all right so once I get that finally checked and sorted out we're gonna start laying
up another wall frame we've got the material to do one more intermediate one while they're
laying that out I'm gonna get the other two post spaces done on these two and then we stack that
in the pile and then we're out of material so we've got a week off then while I mill
hopefully some wood will show up and we've also decided we're going to do another lay up as well
to make sure that all the trusses tie into the wall plate properly we're going to run out the
two wall plates all the way down the building space them level them get them as they're going
to sit on the building and then we're going to place the trusses on them and scribe in
all of the notches that the truss is sitting as well that means once we go to put it up on site
they'll just sit down into it we won't have to mess around at height so yeah it's gonna be
about three days as well doing that right that frame is done and we're gonna pack it away
and put it in the stack so the guys can start laying out the next one and I'll put the other
two feet on in the stack so I'm not in the way so I got those those two to do
and then we run out of timber but that should keep us going until Friday tomorrow yeah another
one bites the dust right hey everyone Friday afternoon Steve and Howard have just uh got
another wall frame mostly done me and Nye have been making a new mid-rail because one of the
mid-rails is a really bad conditioned piece of wood as it's dried out it's a lot of saps come
out of it it's looking rough so we're just making a new one and so we're just fitting that up just
because it's a much nicer bit of timber and uh yeah Howard's just waiting for us to finish and
then he's gonna fit this last post to this one and then that's it we're out of timber
so I need to mill some more and then we can carry on uh week after next is the plan I was hoping to
get a video out this Friday but it's got no internet so uh yeah you'll probably see this
next week all right well that's uh gonna be the end of this video all of these bits here are done
and ready to come back to my place and be put up a lot of work went into getting into that stage
a lot of work still lots to do but uh that aspect's done and one more we've placed that
mid-rail that's sorted out back in the stack got this next frame underway so we need to do
one more of these and once we've done one more of them we need to make three more trusses
and then once you've made the three trusses we need to get the two wall plates laid out
put the trusses between them and then make sure all of that everything's going to sit right on
the wall plates then we're done but before then I need to mill a load of timber and these guys
have got to go off for a week and do some other work so yeah that's uh basically it now for a
week we'll uh reconvene once I've got some more timber and they're back and we'll get this thing
finished all right hope you enjoyed the video and thanks for watching
