Enduro Bikes- The Ultimate Setup Guide

RockShades
98 followers
#sport #travel #running #marathon #cycling #bicycle #training #race #triathlon #swim #bike #run #adventure #inspire
Enduro and enduro riding has got to be one of the most popular types of riding out there.
Cruising up some climbs, bombing some downhills, and then doing it over and over again
is nothing but smiles for miles. Having your bike set up correctly is crucial.
Now, over my years of racing and years of chatting to other pros about their bikes,
I've got some great tips and tricks. Here is the ultimate enduro setup guide.
Let's kick things off at the front end, the handlebars. Now, 800 mil is a go-to-ish number
for a lot of downhill riders, downhill racers bombing it around flat out. Faster, rougher,
wider gives you a little bit more control. However, enduro is a bit different because
whilst we're doing all of that, we've also got to go back up. We've got a lot of tight twistiness,
we've got a lot of tech, we've also got a lot of variety in where and what we ride as well.
That kind of width is maybe a little bit on the wide side, I would say. Wider bars,
they're also going to change your stance, your body position on the bike. They're going to open
you up, bring out those shoulders, those elbows much wider. Now, this is good when it's flat out,
but like I said, we don't want to be like this when it's real tech. We want to come in a little,
not like a little T-Rex obviously, but if you can bring it in, it's going to give you that
more wiggle room to play with. Here, 740s to 760 mil is the go-to range. I run 760s pretty much
across all of my bike except for my dirt jump bike and I run 740s on my XC bike. I know a lot
of pros basically do the same as well. If you're running 800s at the mo, try cutting them down,
but do it incrementally. Maybe just 5 mils or 10 mil at the most each end until you get to maybe
the width you want. Remember, you can take off metal or carbon, you can't really add it back on.
Onto controls. Now, we used to set our controls up so they were just comfy all the time. The old
adage was that the lever position would run in line with your arms when you're sitting on the
bike and riding along. The levers would be at the same angle if you were to carry on a straight line
from your upper body. Now, this doesn't really work anymore. Enduro is all about flat out downhill,
right? I know you've got to get back up, but the time section, the important parts
are bombing downhill. For that, we need our positions slightly changed. Think about it.
If you've got quite a steep lever when you're going downhill, to then reach for further forwards
and get it, it becomes harder. You're going to want to flatten your levers. You'll notice it's
kind of the reverse when it comes to XC. Those guys, and myself included again, are running a
steeper lever. You'll spend a lot more time in the saddle, a lot more time sitting up,
a lot more upright, so you can get away with that old all-in-line kind of feel.
Bombing downhill, steeper your bike goes, I would say the flatter you want to put your levers. Also,
with your controls, have a little experiment where your brake levers are going to sit both
inbound and the actual lever reach themselves. That's different for everybody. I run mine quite
far out. I know Neil and Blake, they run theirs quite close to the bar. It could be dependent
upon hand size as well. Also, you want to be ergonomic. You want to be able to reach
the levers and the thumb shifters, the paddles, if you like, whenever you're riding.
My dropper here on the left-hand side, it sits nicely at the end of my thumb. I don't want it
running too far in because it becomes harder to press. You never really want to have to
move your hand as such to be able to push any or pull any of the controls.
Last but by no means least, in enduro, handguards, not controls as such, but a lot of riders are
running handguards. This is a bit of a love-hate. There's a Marmite thing going on with handguards.
They do serve a purpose. They will protect your hands from bashing them into trees,
brushing on any kind of cactus if you're out here in Arizona.
Some people think they look a bit kooky, maybe not necessary all the time.
It's a personal preference thing. In the world of enduro, a dropper post
is crucial for two reasons. One, you got to go up the hill, so you need your seat
at the correct height. It can't be down low, really uncomfortable to ride. That ain't going
to work. At the same time, when it comes to descending, you want it as far away as possible.
On this bike here, I've opted for a 200-mil dropper. That's as long as I can get in. I've
got it basically slammed all bar, maybe 5 mil. The important part is this height here,
so when it's up fully extended, it's the correct height for my height, my extensions, and my legs.
It's comfortable when I'm pedaling, essentially. I've gone for the longest drop I can so that it
slams this all the way out the way. It's as far out the way as it can possibly be for when I'm
shredding back downhill. Now, two reasons for that. One, it's out of the way. It means I can
move my body weight around as much as possible. Also, it just means I've actually got a lot to
play with as well. If I only want it back up a touch just for a quick sprint or something like
that or to take the weight off of my knees or my legs when I'm getting tired, I can without having
it to go all the way. Obviously, though, when it comes to dropper posts, you do want to go for as
much as you can, I think, but you've got to check the insertion length on your frame. Not all frames
are going to take a 200 mil. You can see the seat tube on this Orbea here is really long so you can
get away with it. Double-check with the manufacturer first. Let's talk frame size.
I'm six foot. This is a size large. It's 485 reach and it fits me bob on, but people like Jesse
Melamed, Richie Rude, Jack Moyer even, they're of similar heights and they're all sizing down.
Why is that then and should you? The reasoning behind it is basically a smaller bike is slightly
more agile, a bit more maneuverability. You can throw it around tight twisty tracks. It comes
into its own a little bit more, but all of those guys have been known to say that actually when
they're back home riding trails they're comfortable on, trails they ride all the time, they'll ride
the correct size bike for them, if you like, a size large instead of a medium, et cetera.
Now, bike industry, things are getting longer, lower slack as well. Like we said before,
droppers are getting longer so you can get away with riding a size down, but that's not to say
they don't. That's not to say that you should either. For most of us then, well, we're only
going to have the one bike. We don't have the luxury of being able to choose between sizes.
Unless you want that small, fun, flickable bike that you can ride on tight techie terrain and
you don't ride too much of the flat out stuff, maybe go down a size. However,
I'd probably stick to the size that's recommended for you.
Now, we're on to suspension. Suspension is a humongous topic in itself, but enduro bikes,
typically 160, 170, maybe up to 180 on the front mill travel bikes, they're big burly things. Few
people like to break the mold, Jesse Melamed, Reece Werner, they ride slightly lesser travel
trail bikes, but still with a lot of travel up front. It's how these bikes are set up,
how this suspension works that is done different in enduro. With suspension set up, if we think of
downhill, we think rock solid suspension, high speeds, big impacts, and sag can be around 15%
to 20% for those kind of guys. The sag on an enduro bike is going to be a little bit more.
Riders are actually going to set up their bikes a touch softer. Because they're doing a lot of
stuff blind, they don't know what they're going to hit a lot of the time. Sag could be 25% to 30%
on a lot of pros' bikes. Mine include, I run mine at about the 25% and it ramps up quite firmly,
but it's beginning of the stroke is softer, therefore, it will absorb all the small bumps
and absorbs all the small bumps. When there's a big hit, it will ramp up and take that as well.
When it comes to the actual setup of the suspension, now, a lot of the time,
it's going to be an air fork up front and coil is creeping in at the back. A lot of air shock still,
mainly because of the weight, actually. An air shock is just lighter. Although these are big
burly bikes, they still want to keep the weight down, so you'll find an air shock. I like the
feel of a coil, so that's why I've got one on the back of mine. Riders are also going to run their
suspension so it ramps up. It's going to be soft at the beginning of the stroke to absorb all that
small bump and have that nice little bit of compliance. Should there be any unexpected
big hits, then it's going to ramp up nicely and absorb that as well. Slightly softer suspension
is also going to be a little bit comfier as well. Remember, enduro bikes, enduro racing is big days
out on the bike. If you've got rock-hard suspension, well, you're going to need some
rock-hard arms to handle that all day. Slightly softer suspension is going to be a lot more
forgiving on the body. You're not going to get fatigued as quickly. You're going to be
able to ride longer and harder, hopefully. There's another definite perk to it there.
Moving down to the belly of the beast, your drivetrain here. We're going to talk cranks and
pedals right now. Enduro riders, myself again included, I'm putting it out there,
I'm myself in that bracket, are running shorter cranks. These are 165s on this bike. The reason
for that is less pedal strikes, cadence can be kept nice and high, and you're going to run quite
a small chainring on there as well. 32 to 34 is kind of the norm. What a lot of riders will do is
we've obviously got a little chain guide at the top, but this is going to stop the chain from
bouncing off. I don't, but a lot do. It can be recommended if it does get really rough and rocky.
It's a bash guard, something that's going to bolt to the ISCG tabs here underneath and protect that
chainring from any rock strikes as well. Onto pedals, I'm running flats today, but normally,
we know that I'm a clip kind of guy. Clips, when it gets really rough for me, help keep my feet
attached, obviously, in control of the bike all the time, and I don't have to worry about them
skidding or bouncing about. Having said that, if you do want to run flats, a nice solid platform.
Big pedals for me. You can get a small version of this pedal as well, this Crank Brothers here,
but I run the big one. I'm big-footed, I'm big-pedaled, so I want a nice big contact patch.
That way, if my foot does jiggle about a little bit, a smaller pedal, I might slip off of it easy.
I haven't. I've got a nice solid platform there. Now, it might depend on what shoe size you are,
have a little think, but combining it with the right shoes as well, obviously,
makes a huge difference to the amount of grip you're going to get.
Onto wheels and tires now. This is one of the most important setup aspects of an enduro bike,
I think. Let's start with tires. Look, 2.6 up the front, 2.4 at the back. Anything within that width
range, I think, is going to be bang on. I, myself, run a 2.6 up the front and a 2.4 at the back,
like I said. What I'm doing here, I'm running enduro casings. These are virtually some of the
thickest, most toughest casings you can get out there because you are pushing this bike to its
limits. You're riding downhill tracks, essentially. They need to be solid rubber underneath. You need
to have a good trusting tire, something that you know the sidewall's not going to split or tear,
or tear a knob off the top of the actual tire itself, et cetera. These are the enduro casing
ones. With that, generally comes softer compound. Now, you might be thinking,
Rich, flipping it. You've got to ride this around all day and it's going to weigh a ton.
All right, yes, they're not as light as trail tires, but myself, and I know pretty much every
other racer out there, will sacrifice weight over reliability here because they don't want
a puncture. A puncture, when it comes to enduro, is the most annoying thing ever, especially when
you've got tubeless and inserts and stuff to deal with trail side. It's a hassle you want to avoid.
Soft compounds, nice and grippy, nice and comfortable, slightly narrow on the back.
I run a narrow on the back because I like the back to have bizarrely a little less grip so I
can flick it around. I like to steer with the rear, shall we say. That's why I go for a 2.4,
and in my head as well, it's slightly less rolling resistance. Those are married up to
wheels, but what wheels? Now, back in the day, carbon was a bit of a blasphemy term when it
came to enduro racing. People were thinking, carbon wheels, they just break, not worth the
hassle. Aluminum, old, reliable, faithful. If it busts, you bend it back. That kind of stigma
has changed. However, carbon wheels are stiffer. If you've got a really stiff bike, a really stiff
frame and you're running lots of other carbon parts, carbon wheels on top of that could be
quite fatiguing. You might feel a lot of small bump and vibration through it. The whole breaking
a lot myth has been debunked. Teams like Pivot who are on Reynolds, shall we say, well, they've
done experiments where they've ran the same wheels the entire season and not had a problem at all.
With carbon wheels being more reliable now, some of that weight that you might have gained on the
heavier tires, well, you can claim back on a lighter wheel. Like I said, feel does come into
play. You can see on my bike here, I've got the FSA gradients front and rear, solid carbon wheels.
I like the feel of them. They work well with the tires I've got and in conjunction with the frame.
I'm not running carbon bars or anything like that. Actually, that sort of vibration coming
up through the bike isn't affecting me too much at all. Two-pot, four-pot, six-pot, 160, 180,
203, 220. Braking is a bit of a minefield. Here's what I would recommend when it comes
to enduro. A four-pot brake is going to be a must because it gives you a lot of power,
shall we say. There's four pistons on each brake pressing against a disc. That's the way to go
because remember, you're going to generate a lot of heat and a lot of speed, so you're going to
need a lot of braking force. When it comes to rotor size, well, in downhill,
I hop back to that a little bit. The 220 is creeping in quite consistently now. I think
personally, that's a little bit much. We still don't really see that too much
in enduro because whilst we do have some very flat-out tracks, if you're away racing or even
local racing, the speeds are generally still a lot slower and the need to brake as harshly
as quickly is a little bit less as well. 200 up front, 180 out the back, or 200 out the back is,
I think, the sweet spot. I think that is the creme de la creme of what you need for braking.
It's what I run. It's what a lot of people run. Floating rotors are the one. This essentially
means it's not one big piece of metal. There's rivets in it, so it's detached.
That means it can contract and expand. It can dissipate heat. You can even get vented rotors
now as well, which help pull air around and keep them cool as well. There's fins on your brake
pads to help keep the brake pads cool. That's really, I think, the optimal setup for any kind
of enduro race bike. Enduro riding is all about self-sufficiency, I like to think. Remember,
if you're out on your own, out doing a big loop, racing or something, you're going to be on your
own or maybe have the odd rider around you, of course. It means if you get into a pickle,
you've got to sort it out. Carrying the right equipment, carrying the right tools,
spares, bits and bobs needed to fix your bike is absolutely critical. There are some clever
way enduro riders and manufacturers of enduro bikes have come to do this.
Firstly, frame storage. It's a revelation when it comes to mountain bikes, I like to think. It's
pretty genius. Take my Rallon, for example, and a lot of other bikes out there. In here, you lift
off this flap, essentially where the water bottle is, and you can just store stuff. That whole down
tube is hollow. People like Orbea again, inbuilt frame tools. In here, I've got a little magnetic
multi-tool just inside the linkage. There's a 6mm as my quick release at the back. It's really,
really clever. On top of that, other companies you can add onto your bike. Look, I don't want
to harp on it, PEs, the dust caps on the valves, a valve core removal tools or a spoke key. That's
mind-boggling. Then strapping stuff to your bike as well, finding nice, neat solutions.
This Topeak strap here, I've got CO2 canister, the inflator. I've got these Topeak tire levers,
which also are chain splitters. Having all these really clever storage solutions just worked well,
even like having a spare power link and some duct tape actually on my handlebars,
just in case I needed it. Gearing. What gearing should you run,
and what gearing do the pros use? Well, in the EDR, they're absolute weapons. Whilst a lot of
us are using 50 to 52 biggest sprocket on the back cassettes, those guys and girls are running up to
about 45. On the front, we're running 32, 34, maybe some of us 30. They're also running that.
They're running that 32, 34. Remember, they've got the legs for it. That's what they do. They're
pros. If you're new to it, I'd recommend one of those big wide ratio cassettes at the rear.
It means you've got all the gearing. It means you can get up most climbs,
but you can also sprint back down as well. A 1x system is obviously the way to go now.
1x12, ideally. 1x11 works absolutely fine. Hey, if you want to run 1x10,
no problem. Remember, the other reason EDR guys and girls do it as well, if they're running that
45, the cassettes are actually considerably lighter. They are looking to save weight in
certain places. Whilst I said about tires, you might want to sacrifice weight in certain areas,
you don't want to be hauling around an absolute tank of a bike all the time. If you've got the
legs for it and you can save some weight, running a smaller cassette is one of those areas that you
can shave a few grams off of. Actually, I just really thought about something on the tires
thing. Inserts, great idea. Stick an insert in the back. Remember, they're taking a lot of impacts,
so an insert on the rear is a bonus as well. Anyway, that is my ultimate enduro setup guide.
Let me know what you think. Is there anything you do differently to your enduro bike?
It's pretty much how I have mine. If you want to know any more questions about how I have
mine set up for racing anything from EDRs to local enduros, let me know in the comments down below.
I'm always well-keen on the enduro stuff, so drop us a question. I'll get down there and answer it
for you. For now, from sunny old Phoenix, I'm out of here because I need a good old glass of water,
not a cup of tea like you thought I was going to say. See you.
