Hesco 4601 NIJ Level IV / NIJ 07 RF3

Ballistic Lab
1 follower
Jan 11, 2025
Hi everyone.
Welcome back to the range.
My name is Matt, also known as the King of Armor Destruction,
the Armor Wizard, Zap Zap.
We've got a body armor test today.
This is from HESCO in full transparency.
Greg over at HESCO sent us some of these plates to demo and some
others with no strings attached.
This particular model is the 4601.
This is a multi-curve level four NIJ certified model.
We have two sizes here.
This is a 10 by 12 model.
It weighs 6.55 pounds or 2.97 kilograms.
It is 1.20 inches thick, or again, for those across the pond, 30.36 millimeters.
You can see all those sexy curves right there.
There is our Starburst logo to indicate that this is an NIJ certified model,
meaning that there's a bunch of additional checks and balances and quality controls
that ensure plate number, what's the serial number on this guy?
Something something 420251 is built exactly the same as serial number one
that they submitted to the NIJ and there's followup testing every so often.
I don't remember what the frequency is to ensure again, that the plates meet
the threats that they're supposed to stop.
The other 4601 that we have here is a size large.
So this is larger than the other one.
It weighs 7.59 pounds or 3.44 kilograms.
It is 1.18 inches thick, or for those again across the pond, 29.98 millimeters.
And again, it is multi curve.
You can see we've got a curve here.
We've got a curve here fits your body very nicely.
There are advantages and disadvantages to flat single curve or multi curve,
depending on your body type, a body type like myself, I find multi
curve to be the most comfortable.
Now, if this is the first time you're coming across one of my videos,
here comes the long winded speech over here on my channel.
We do things completely different than a majority of other YouTubers when it
comes to demoing or testing body armor.
I've read a lot of the NIJ protocols and I'm not a lab.
So I'm keeping as many of these constants as possible out here in my range.
So we shoot at 45 feet.
That is the official testing distance for rifle armor.
We also shoot at zero degrees because that represents worst case scenario.
If there's anything you can take away from these demos is I'm after worst case.
Generally with level four, you only have to stop one round center of mass M2AP.
And we're here to show that ceramic armor is definitely multi-hit capable.
And we like to, again, go to the worst case scenario for our armor testing.
We also use a giant clay briefcase filled with Roma Plastilina number one
clay donated by Chavant that acts as our compressible media to put
the body armor up against.
Now that's the same clay that the NIJ uses, but they heat it up to a certain
temperature and they drop a giant steel 22 millimeter ball on it and they
check the dimple and certify it.
We're not going to do any of that out here.
So it's just a representation.
It's about 80 to 85 degrees outside here today.
So if you see like a 60 millimeter indent in our clay, potentially
that could mean that it's failing.
If you see a threat penetrate against this plate or stop, you should always
defer to any of the actual NIJ testing that the company should produce.
And on the flip side, if you're the company and you see me stop M993 going
2,600 feet per second, you should send that plate to an accredited lab and have
a special rifle threat added to your matrix.
Since this plate employs a ceramic strike face per the NIJ, we've gone
ahead and dropped each plate on its face two times as a preconditioning test.
This particular model has foam on our strike face.
And in all of our newer videos, we mark a DT and a TQ on our plates.
If they've been dropped, tested, and I don't hear any cracks in
the plate when I torque test them.
That's when I take each opposite side of the plate here and
kind of put some pressure on it.
And if the strike base is cracked, you will hear it.
The HESCO 4601 does employ a edge to edge strike face, meaning that this
particular panel, if it were 10 by 12, all the way out to the extreme edge
is the ceramic, and then the polyethylene is behind it.
Some plates, in order to sell you a lighter plate, we'll sometimes put a
foam ring of upwards of one inch or more on the edge, and then your ceramic
is only here, so then you actually don't have true edge to edge coverage.
So that's one good thing that I like about our HESCO plates.
We also use a chronograph whenever possible, a pro chronopal digital
DLX, because we need to know the velocity of that bullet.
The NIJ spec for M2AP calls for 2880 feet per second.
And finally, we put a spreadsheet here at the beginning that we kind of
foreshadow all the threats that we're going to shoot at it.
We fill out all the velocities and penetrations at the end, and we also
do a tear down because a lot of my followers are interested in knowing
what the inside of our plate looks like.
All right, we've got plate number one strapped up and we're ready to take
our shots as mentioned for NIJ level four or the upcoming NIJ 07 RF3.
It only has to stop one shot of M2 armor piercing center of mass.
We're going to go a little above and beyond.
We have four rounds of our M2 armor piercing.
It's 163, 165 grain full metal jacket with a very long
hardened steel core penetrator.
Now this is in 300 Winchester Magnum and we've loaded it up to meet close
to the spec of 2880 feet per second.
Sometimes with the weather, we end up a little hotter.
Usually with our surplus ammunition, you won't see that specification.
So sometimes if you see other people shooting M2 armor piercing at lesser
quality plates and it stops it, it's usually because they're using a 22
inch 30 at six and you're not going to see that velocity.
We've got a TC compass here in our Boyd's chassis.
Got a Phantom M2 up front from Yankee Hill.
We'll take four shots on this plate.
And then I think we take some five by six on this, depending on how it goes.
And we'll move on to the cool stuff for plate number two.
Oh, we were a little fast there.
Almost a hundred feet over spec.
It's okay.
I really need to dial these loads back.
All right, let's go see what we did with those before we go to some
five, five, six threats on the same plate.
All right.
We've got all four shots on our plate.
These are all fair hits one, two, three, and four.
What I like about HESCO is that they laminate their strike face.
So as you can see, we don't have any fragmentation coming out of the side.
Now we do have ceramic that kind of spits out the front a little bit, but when we
talk about fragmentation or spalling from steel armor, when bullets hit steel, the
fragments are then broken apart and splashed outwards.
When you hit ceramic with a bullet, the ceramic degrades and breaks up the
bullet, and then these fragments that break off aren't going as fast as the
bullet fragments when it hits steel.
Place those bets in the comments below.
Helper hand.
Oh, raggy.
Now in HESCO's defense, these plates only have to stop one hit dead center of
mass at 28, 80 feet per second.
And for whatever reason, we were well over spec, but shots number one and three were
stopped.
Number two is a pass through.
There's a hole right there.
And then number four, we'll have to confirm because it looks like it penetrated right
there, but very impressive that we stopped that one over the spec, you know, 200 feet
per second.
And generally speaking with our multi curve plates, we have what I've seen as a
weakness in this particular area.
So it's a good thing that it stopped it.
Now, like I said, because this plate is laminated, we're going to throw some five,
five, six threats at this plate.
Our clay is warm.
It's about, it's been sitting out in the sun.
So as far as back face goes, that number one shot would be a good indicator.
33 millimeters.
Number three is a little worse for wear.
42, not too shabby if I do say so myself.
Let's move on to some more threats.
Yeah, I gotta see how deep this shot is.
There's no disagreement that plate number one is compromised, but the way HESCO likes to
laminate their strike faces, other parts of the strike face remain intact, even if
they're cracked and taking those hits.
So we brought out our, again, worst case scenario.
This is a 22 inch TC compass, got a turbo five, five, six up front.
So this is maximum real world velocity.
We've got three very common five, five, six rounds.
We have M193, 55 grain full metal jacket known for popping steel armor because it's
velocity. We've got M855.
That is a 62 grain full metal jacket with a little conical steel penetrating tip that is known for
popping polyethylene plates and or some ceramic strike bases that have very thin strike
bases. Then we have the U.S.
Army's current issue ball round all the way down to basic.
This is M855A1, has a copper core and a very large arrowhead steel tip hardened to around 60
on the C scale versus around 50 for the M855 tip.
I want to get these out of order.
So M855A1 will be third, M855 will be second, M193 will be first.
This should be on the upper part of the plate.
Very good velocity off this M193.
I'll place this one right next to it.
Then the M855, I want to go on the third line.
Now the A1, our spicy boy.
One, two, and three.
All right. I've been using this threat a little more often in some of our recent tests.
This is 545 by 39.
This is 7N6M, it's a 52 grain modernized version of 7N6.
The core and bullet weight are identical, except this one is hardened to around 60 on the C scale.
And again, because I like worst case scenario, we have an SSG82.
This has like a 23 and a half inch barrel.
Very interesting bolt gun from East Germany.
Only I think 600 of them are in the U.S.
Feeds from a box magazine.
Pretty nice little gun.
Definitely not set up for left-handed shooting.
This will be on the bottom middle of the plate, or bottom kind of where I have all the specs written at.
That was a little close to where I wanted it.
Nice.
Pretty good velocity.
545 is loaded to a lower pressure, like 20,000 PSI, less than 5.56 NATO.
So we're never going to see the velocities that 5.56 can achieve.
At this point, I think we're done with plate number one.
We surely could throw more hits of 5.56 at it.
But M193 shots number one and two, 7N6M shot number two.
That is an edge shot.
Then we have M855 number one and two.
Then we have our A1 shots number one, two, three, and four.
And then down here is our other shot of 7N6M.
That's close to not being a fair hit.
Helper hand.
No pass through.
I did beat the clay flat before this one.
And there are no penetrations from those 5.56 threats on this already compromised plate.
I guess we're going to have to step our game up for plate number two.
Plate number two is strapped up and it's ready to rock and roll.
I've got our 16-inch CZ557 Urban Counter Sniper.
Got the Phantom M2 up front for maximum noise reduction.
Got our 130-grain M993.
This has a tungsten core penetrator on it.
Very, very nasty.
Most level four is not rated to stop this even from the 16-inch.
This has an aluminum strike face.
So we'll take a stab at it with the first shot.
Again, I'm all about worst case scenarios.
So this is well outside of the purview of the NIJ.
I would assume HESCO has never tested this, or at least publicly.
2872.
My battery's dying on the chronograph.
We brought 30 cal back out with some specialty threats and depending on how it
goes with these, we can go back to our 300 wind mag.
We've got M80A1.
That is the Army's current issue ball round in 7.62 NATO.
It's 130 grains with a copper core and a large arrowhead steel tip.
Tip, just like M855A1, but not as hard.
Then we've got our M61 or P80 black tip.
This is from like the early 1950s, 1960s.
Core is similar to M2AP, but not as long.
It's more like an arrow.
Pretty good at penetrating, but I think M2AP is better.
Then we have my favorite M14A1API, Mr.
Flashy Flash.
Got a lot of incendiary compound in that guy.
We've got a 24 inch Savage Access 110 tactical.
We'll take the M80 shot, M80A1 shot.
First, we'll put that on the upper part of the plate.
Good velocity off that.
P80 black tip.
I'll place on the third row of dots.
All right, Mr.
Flashy Flash.
That pop, I love that stuff.
So much fire, so satisfying.
As far as shot placement goes, these are all considered fair hits, but our
threats that we use are again, well outside the purview of the NIJ.
Our M80A1 shot was right up here.
Our M993 shot was right there.
Our P80 black tip was right there.
Then our M14A1, Mr.
Flashy Flash is right down there.
Place those bets in the comments below.
Oh, raggy.
I did confirm that we have a penetration from the M993, but all of our other
threats, we'll peel this off in a second and confirm, are stopped.
It looks like our M14A1 is the worst for where, as far as back face goes.
Usually always those edge shots are the worst.
34 millimeters, 29.
Then the M80A1, which is very close to the edge, 30 millimeters.
That's a very controlled back face.
Again, always seek out the actual NIJ reports from your manufacturer
for official specifications.
This is just a representation.
There's a lot of discussion online.
When somebody sees this video that they say that these dimples
will put you out of the fight.
And I think a lot of it depends on your body build.
Again, all the NIJ's research says that any of these dimples under 44
millimeters is considered survivable.
There is a gentleman from many, many years ago who took a point blank 308
shot on camera while he was standing on one foot talking and he didn't skip a beat.
Now he did get shot in the lower abdomen area on that plate versus in the chest.
So, you know, your mileage may vary.
Just don't always assume that these dimples are the end of the world.
I have two more shots that we'll take at this plate.
We've brought the 300 Win Mag back out.
We've got M80A1 and our M14A1 API, but we have them loaded
in 300 Winchester Magnum specs.
I'll take the shot of the M80A1 first.
I'll go down and check if it penetrates, foreshadow a little bit.
If we take the M14A1 shot, you mean you know that M80A1 didn't penetrate.
3,500 feet per second.
Yes, right where I wanted that sucker.
So much fire, so satisfying.
All right, our M80A1 plus P plus was right down there.
That is two inches from the edge.
That's considered a fair hit.
Then our M14A1 plus P plus was right there.
That is two inches away from that shot.
Although, like I said, level four, it's designed for one hit.
I think we're doing a pretty good job of showing that depending on the threat,
they are multi-hit capable.
Uh-oh, raggy.
Our M14A1 API popped right through that guy, but our plus P plus M80A1 did not penetrate.
I did come down and check that beforehand.
Very, very interesting.
Could be argued that at this point, that part of the plate is very weak.
I should have placed these shots maybe in a different order.
Maybe you should put that one up here.
But impressive.
Let's tear these guys down.
Now for a fan favorite, the tear down.
This is where we see what the guts of our plate looked like.
This is our back cover of plate number one.
Confirmed our penetrations were the second and fourth shot of M2AP.
Again, those are above spec.
We have a foam blunt force trauma on the back.
296 thousandths thick or thereabouts.
I always feel, in my personal opinion, this foam can be limited in use.
I would rather have that thickness and replace it with more polyethylene.
What I do like is that HESCO is using a foam on the outer edge of the plate to
protect any bumps and strikes that come from this on the outside.
This is not a foam strike face reducing ring.
This is on the complete outer edge of the plate.
We have polyethylene.
It is pressed, although after those shots, it's a little bit wobbly.
We measured that around 480 thousandths thick.
You can see all those shots on there.
Here is our ceramic strike face.
Very telltale that this is from HESCO.
We have this blue tape usually on each corner there.
Measure that right around 345 to 350 thousandths thick, depending on the curvature.
As I mentioned, you can see this plate, the strike face is laminated and it is,
for the most part, still all in one piece.
There is the backside of it.
If I had any room for constructive criticism, it would be better adhesion
between this strike face and our backer.
Usually after I'm done shooting these, I can run the X-Acto knife or the safety
knife around the edge and easily peel them apart.
Then we have our super high density yellow foam up front that's
used as our drop face protectant.
I measured that right around 130 thousandths thick.
Like I said, I'd rather see this thickness on the back for our blunt
force trauma and replace the additional thickness with polyethylene, although
I'm guessing that's going to add to cost.
Again, you can see that foam is just used on the edge.
Here is strike face number two for the large.
Again, there's cracks in our strike face, but for the most part,
why did the camera do that?
Look at that.
That's solid.
You could stop five, five, six threats on the rest of this all day long.
Our API, I should probably should have put that up here, but it is what it is.
Here is our backer again.
The only confirmed penetrations on plate number two were the plus P plus M 14
a one API and the M nine, nine, three and nine, nine, three is very,
very, very hard to stop.
And there you have it.
That's all she wrote folks.
Well, folks, I would call today a successful outing because I didn't cut
myself when I tore the plate apart.
Cause I remember my gloves this time.
I would say our HESCO 4601 plate did very well again for our NIJ level four threat.
You only have to stop one of those center of mass at 28, 80 feet per second.
And plate number one stopped two out of four, well above the spec velocity.
Again, that's on my part for loading ammunition that I thought was to spec.
And then because of the temperature changes, then I ended up getting more
velocity, we stopped a whole bunch of five, five, six threats and our five,
four or five threats on that same plate.
When it already took those four shots, plate number two took some advanced
threats and Mr.
Flashy flash put an end to it as well as our M nine, nine, three.
I do like the construction of our HESCO plates.
I love that laminated strike face.
I love that we have drop face foam on the NIJ certified models.
Again, I would like to see a little bit more polyethylene on their plates
versus that thicker foam on the back.
But again, I'm not an engineer.
I don't have access to all these numbers to know whether or not that extra thick
foam is actually paying off for reduced back face.
With all that being said, it's time for me to get the heck out of here because
it's Sunday and it's movie night.
We're going to watch back to the future, but at the end of all my videos, I take
a moment to thank all those who helped make these possible because there's
a lot that goes into them.
Number one is my Patreon and subscribe star fans.
I have a link tree in the description below, like various other content
creators, there's affiliate links and discount codes in there, and they
essentially earned me a sales commission, which I put right back in the channel.
I actually built two new clay briefcases out of wood this time,
so they can repair them.
And now I have to go to Chavant and get a quote to price out the clay that goes
into them, and I think it's going to probably run me anywhere from 12 to $1,500
just for modeling clay.
Number two is Greg over at HESCO again in full transparency provided us with those
plates to destroy with no strings attached.
I do believe that those will run you a little more than other level four plates.
I think they're right around 500 to $600 each, depending on the size, you know,
they're small, medium and large and they're swimmers cut or sappy cut.
I do believe S-TAC has these available if you're looking to purchase.
And of course, number three is you all for watching until next time,
I'll catch you at the range.
