Bringing A Rowe CD100A Jukebox Back To Life, Let's Hear What She Sounds Like PCB Repair Part 2

Joe Jukeboxes
160 followers
530 Video Views·Jan 7, 2025
ladies and gentlemen this is Joe's
classic video games back with another
cool jukebox repair video for you today
we did a video on this uh CD box that
we've been messing with it's a row Ami
CD
100a that has given us some issues and
in the previous video we found something
was on
fire so the mech power board was on the
mech control board was on fire and uh
whenever you turned it on it smoke would
come out of it uh so we figured out that
one of the
um uh Darlington transistor array chips
we'll look at it here again in a minute
was burnt up and so uh it was smoking
for whatever reason so we went through
it tested the power supply it was fine
we tested the uh Motors they seemed fine
replaced the chip put it back in and the
thing now will run but it just runs
continuously so the the basket runs
continuously and tries to play a record
over and over and over again so I'll
turn it back on and show you where we're
at right
now we're going to mess with it again
today so you can see that the
uh it's just basically
forever playing a record over and over
and over
again and it moves the same amount of
spaces each time so it's kind of like
a it's not selections that are stored in
the computer or anything it's just it's
tripping we're getting an error message
again we cleared that out last time but
we're getting it again okay on
our
CCC we only get the
5vt uh light we're not getting a
permanent at least System
error
okay and
then down here on the
mechoo thing's
heavy um we've just got all the lights
on all the
time so that's not
right so this is a CD 100a but it's been
updated and so they uh whoever had it
took good took good care of it they uh
they put the
newer uh Pro player in it and uh that's
the the board the mechanism control
board for the uh Pro player which is the
more modern one instead of the original
one that came with the 100a it also has
the updated Basket in it that design is
a little different
um uh there's I believe the the board
and the power supply has changed
whenever you change the mechanism power
board so it's it's been updated to the
more modern ones so it's it's not a
problem of
uh old um designs that needed to be
updated it's it's got all the newest
stuff in it uh that they that they put
out for it so we just need to repair
what's in it we should have a decent
playing little machine uh so that's our
that's our uh evidence so far you don't
have a system error or board error light
on the CCC and you have all of the
lights including the board error light
locked on on the mechanism control board
so the first thing I'm going to do is
unplug the U row link where it it sends
the signal from there down to here and
uh see if that gives us a board error
over there cuz I don't know for sure if
the computer is not talking to the mech
board or if the mech board just has all
the LEDs locked
on so that's what we're going to try to
find out so the first thing I'm going to
do is uh try to unplug that uh row link
and see if we get a different error on
the
CCC all right so I simply unplugged the
two- wire connector that is the row link
and
now the row link command
and light is on and doesn't go off the
system error and board eror lights
though are not on so in other words the
CCC is trying to send a signal and it's
not getting anything back but what that
makes me believe is
that this board is probably talking at
least somewhat to the CCC or it wouldn't
uh it wouldn't have just done that that
light would
have stayed how it was if it wasn't
talking before you know so there's
something it must at least be attempting
to communicate with the uh with the CCC
so I'm going to take this back this
board back out though and put it back on
the bench we'll go back in it it it may
be um that the the U 2003 chip that we
that we Chang the other one may have may
be screwed up as well and it's got the
LEDs locked on so we might just try
swapping that or we'll check it out all
right so here is the MCC mechanism
control computer and so what we changed
last
time was this chip because it had a spot
on it where it was uh
basically uh had a big bubble in it
where the chip had shorted
out
so it is a uln 2003 a now if you notice
there is another one right here next to
it one of our problem is problems is we
don't have the schematics for this we
have the schematic for the Jukebox but
they updated the MCC so the schematics
for the Jukebox don't have this in it so
you got to get a whole set of schematics
for a newer version of the CD 100 and I
don't have those so I mean I could go
spend $40 and get a copy of them just
for this one board
but I don't really want to do that so
I've got a I've got a copy again for
this uh system where the um it's the
older version of this it uses similar
setup
but
um the the main difference between this
one and the and the previous one is that
this one was designed more for using the
uh the pro player instead of the older
version of the CD uh reader that they
had so on the older schematics it shows
that one of these chips primarily runs
the motors and things so whenever we got
it on the previous video none of the
motors were moving or anything it would
just sit there and then smoke would
start coming out of this board because
this chip had a had a short in it so we
we ended up swapping that
chip and uh so that was obviously the
one that runs the motors because now all
the motors are running well this chip
probably runs all of the LEDs so it
could be that this one is messed up as
well but if you think about it all the
LEDs are locked on and all the motors
are running so the little cam thing on
the left is running uh the the the
basket motor is running you know um so
it could be that both of these are just
running all the time because of whatever
controls them so I believe we're going
to be in a situation
where you've got
this I guess this is the this got to be
the processor where this so processor
Ram ROM I believe the processor is
probably speaking through these to these
chips so we're going to try to track
down what's doing what what's connected
to what but somewhere there's something
shorted where I believe it's making all
the motors run and it's making all of
the LEDs come on hopefully it's not the
the CPU because I don't think I've got
one of
those um another thing
is
uh the thing about the the link if you
didn't catch that basically the link is
two wires and it plugs in here so that
the CCC the Central Command computer or
whatever central control computer can
talk with the MCC and some of the other
boards so it connects here well whenever
that was connected the CCC was acting
like everything was
cool I unconnect it and now the CCC
there's a red light where it's trying to
talk to the MCC
apparently and that light just stays on
and and flickers or I guess it's trying
to send information so that tells me
that there
whatever uh that tells me that the the
the CPU here is actually running because
it must be talking to the CCC and the
CCC is happy with the information that's
getting back until you unpluged the wire
so there most of this is probably
working but for whatever reason all the
motors are running and all of the LEDs
are locked on so uh I'm going to see if
I can track it down and see what tends
looks like it feeds those two chips and
if maybe I might just need to replace
this chip I don't know we'll see what we
can find okay so the the row
link comes in and it goes around the
board and ends up
um connecting over here to the CPU like
on this
side those are the traces there uh so
it's basically talking directly with CPU
now the the CPU connects to this 74 HC
574 which is a octal
flip-flop which talks to these
two but uh
whenever I check the U
um basically the on these the input so
like pin two is the input pin 19 is the
output when you check the the the uh
voltage drop between two
and um 19 there it's like
1.1 right and you get that pretty
consistently and then you get the pin 4
and it's 6 like a like a uh diode or a
transistor usually is and then uh you go
through the other ones some of them are
0.9 some of them are 1.1 blah BL blah BL
blah so I'd like to have a a new one
that I could compare it to because my
thinking is if they're all supposed to
be you know between 0 4 and 6 like you
get a lot of times on a um logic gate or
something uh then I think all of
the um outputs are screwed up except for
the fourth one or the which is actually
the third one pin 4 so I don't know what
that controls though I might have to try
to track that down um one two three four
I'll see if I can track down what the
output does that one might be right and
the other ones are all screwed up which
might be why our lights are locked on or
something I don't know but I I don't
have any of these chips I need to order
some so uh I'm going to see if I can U
tell what the U what the output of that
one goes to and then see if we're
getting normal behavior out of that or
not now somebody had worked on this
before at had already
replaced uh the uh 2003 that we replaced
the
74574 that we're talking about replacing
and the CPU chip so if they would have
put a socket in it would have helped me
but they didn't so when I did this one I
put a socket but it could be that we're
looking at the same exact problem again
you know and this was in a box that was
up and running and then just stopped
working one day uh that we got off of a
gentleman so it it's not like it's been
broke and somebody attempted to fix it
this fixed it at some point and now it's
broke again
so um we're still uh we're still
tracking it down this so I'm going to
see if I can figure out what the uh what
the output of this goes to um through
the uln and then we'll we'll see if like
that item is working properly or
whatever okay so this CPU is talking
through this chip which is
a 74 LS 574
or it's actually a 74hc
574
um which is a
flipflop which is strange because that's
the pin ball machine I'm working on um
but it's a flip
flop uh which I don't completely
understand I'm sure uh many of you
probably know much more about it but
like we were showing earlier this chip
this chip and this chip had been
replaced before when we first got it it
was smoking because this chip was burned
up okay so I'm working backwards hoping
that it's not the CPU again and they
didn't put them in sockets but this 574
I I checked between the input and the
output and you get weird readings on
everything except for two of them okay
so the outputs go to the uln 2003 you
get weird readings as so for instance on
two of them you get a voltage drop so it
measures between the input and the
output you get like
0435 or whatever on a diode check on the
other ones it's all open like 1.1 1.4
whatever now you can't really tell much
by that but two of
them um give you that voltage drop so
what I'm going to do is I had to order
some more
574s and I'm going to check one out of
the cabinet and see if it has the same
type of voltage
drop uh not installed
so if all of these are 04 to
6 input to
output and only two of those are that
could be my problem or one of my
problems obviously the uln 2003 was was
a problem so the two that aren't
shorted uh run to the
two uh
meters and the meters are not running
constantly like
the uh Motors and everything are so I
might be on to something here I might I
might so I'm going to check this one out
of circuit and that one in circuit and
see if there's any differences that
can't really tell you anything without
removing that one
but if the voltage dropped between pin
two which is an input and pin 19 which
is an output for instance is 04 when
it's out on a brand new chip when it's
out of the circuit but then you put it
in here and now it's 1.1 well it should
be less than that which means that
Chip's probably
damaged so that's what we're looking at
so I'm going to check that out and then
worst case we'll swap it in even if I
can't figure out and uh just see what it
does in the machine if that doesn't fix
it my next step is I'm going to order
one of these CPUs and swap that
out so that didn't help me at all
there's no correlation between the
inputs and the outputs um on the chips
using a diode check so you you can't use
that the chef keys at all um sometimes
you can use it to check between like
ground and an
input or hot in an input but I'm just
going to swap it so I'm going to pull
this chip install the socket that they
should have installed before put the new
chip in and then we'll see uh we'll see
what we've got going on maybe that'll
fix
it transplant
successful all right so I'm going to put
the cover back on it and then we'll go
try it again and see if we get anything
different or if we get the exact same
thing if we get the exact same thing I'm
going to need to order the mpu I mean
the
CPU so uh we'll see
though well unfortunately it's doing the
exact same thing
so not looking
good I've got more of the uln 2003s so I
think I may swap the other one that we
haven't swapped yet just to see if it
does anything different with the LEDs
there um and get it socketed but I think
uh after that my only option is to order
a uh
CPU
chip we'll uh we'll keep messing with it
let you know what we figure
out all right so last thing we're going
to try is I removed that chip as well
which is the uln
2003 um that was there just because this
one had burnt up right and I believe
this one may actually control the LEDs
which are all locked on um so it could
be that that's locked on but it's
probably more likely that it's this uh
40 pin chip that they did not put in a
socket whenever they replaced
it right so we're going to try that uln
2003 and then if it's doing the same
thing I'll order one of these and we'll
see if that gets us anywhere now you may
be asking well why are you just
shotgunning it why don't you use the
logic probe well I don't have schematics
for one and two uh it takes weird
voltages that are in the machine so it's
kind of hard to I would have to set up
an external power supply and rig up a
bunch of stuff
it it's easier really to just uh focus
in this area because I think that's
where the problem is so if that doesn't
get it though we'll try some other
stuff so uh I'm going to throw that chip
in we'll throw it back in and see if it
does
anything so that's what that ended up
looking like but guess what still didn't
fix
it so I had to bite the
bullet we're going to have to replace
this one so I have
ordered what I believe
here may be a
replacement
okay that's not actually what I ordered
but that's what they sent me uh so I'm
going to take this one out so again our
thinking it's already been replaced
placed
once we've tried the other ones that had
been replaced as well as this one uh so
this one's next um hoping that that's
the issue I don't have any schematics so
whenever you've got one like this that
they've soldered in and it's a board you
know these traces aren't all of that
this isn't all that sturdy of a board a
lot of times stuff like this you'll lift
traces whenever you start working on it
and they've already replaced it once
which means they've already heated all
of that up once you know
and we believe this chip to be bad okay
I have no use for this chip it's about a
$5 chip I'm going to cut it out so that
I can make sure that I get the holes
clean because it's much more important
to me that I don't tear up the traces uh
than it is to save this chip that I
think's bad anyway so I'm going to cut
with side snippers every leg all 40 of
them if it's a 40 pin chip the only way
to get that out without tearing up
traces is if you get all 40 pins
disconnected from the board and and then
leverage it a little bit and pop it out
but it's not even easy to leverage these
because they have uh uh coupling caps at
the end on both sides so you're going to
end up bending up that cap if you try to
pry that chip out so I'm just going to
cut it out and put a nice socket in and
then put the uh put the new chip in so
I'll cut it out and show you what I'm
talking
about so I cut it out you can save this
for your trophy if you want
it just doesn't have legs on it
anymore but by doing that you don't mess
up any traces so now I'm going to very
carefully go through and remove the
solder from each pin and then pull the
pin out each one until I get it nice and
clean takes a little
longer well I don't even know that it
takes a little
longer it's you Lo all all that you lose
is this chip to hell with that
chip
huh what do you think huh huh I can see
where the previous
poison look they marked up the uh board
right there that must have been how they
were prying it out and then right there
too neither of those are mine
[Music]
people came out pretty
clean back's pretty clean I'll touch
that up whenever I solder the new stuff
on but um I'm put a socket in it I don't
have a 40 pin socket so I'm going to put
the the inline
ones uh but uh the whole thing is we
think this is the problem but we don't
really know and then another problem is
we don't know if this is a real
Chip I believe it is but you can't trust
any chips that you buy from anybody
really so hopefully this is a real
chip um but since it's in a socket now
if it's not we can keep messing around
till we get the right one in
it it was it's weird how it's just doing
the same thing over and over again it
seems like it's it's got all the LEDs on
and it's making both of the the two
Motors run at this weird little uh
interval um it's almost like it's in a
test
mode but I don't know of any test mode
that does that right I have heard some
of you that know what what you're
talking about more than I do but aren't
there some
processors that if they don't get
software they run a test like
that because basically it's it's uh
exercising all the
outputs so it'd be a damn shame if this
now remember when we started on the
other video this chip had a hole burn in
it so it would definitely was a problem
okay we replaced that chip and it
started doing what it's doing now so we
we replace this same thing we replac
this same thing now we're replacing the
mpu wouldn't it be
something if the way this chip operates
is if it doesn't receive
software it just exercises all of the
outputs and that's what's going on I
hope that's not it because I don't think
I've got a I don't have any way to get a
copy of that
software but I was just sitting here
looking at that eom thinking about that
okay so I'm going to put a socket in it
put the chip in it and then we can pop
it in the machine finally and see if
maybe that fixes
it okay we are installed I'm going to
put it back in the case and then we'll
put it back in the machine keep your
fingers crossed people now the whole
time I'm gone I need you I need you to
keep your fingers crossed that this is
going to work for me cuz I don't know
what to replace after this I'd have to
buy a whole new board n good
Lord so hopefully this will fix it if
not I'll have to keep asking people
online the problem with asking questions
about repairing stuff like this online
is nobody the people that know don't
want to tell you so all you get is
people on online that are trying to help
but they don't know what they're doing
they've never seen one you know um kind
of like me I don't know what I'm doing
with this I've never messed with this so
hopefully that'll do
it well guess what
right the noise you're hearing is the uh
CDs moving up
top uh okay so none of the lights are on
except for the 5vt light which is the
one you want
on and then up
here we have our 5vt light on and our
row link command light on which I
believe might be correct
I don't know
man maybe we should try like putting in
a selection and see if it does
anything it might just be completely
broke now where it's not even trying to
do
anything or it might be fixed I don't
have a CD in
it
um zero selections remaining so I guess
it
won't
[Music]
hm damn it that's right these Juke boxes
you have to put money in
them uh how do I add some
credits again I have no clue if it's
going to do
anything
uh let me figure out how to add some
credits because it doesn't
have a bill acceptor or anything in it
the coin stuff's all been been taken out
um
H well I kind of like what it's doing
it's not doing what the problem that
we've been
having and our three lights are still on
on the power supply so none of the
voltages are shorted or
anything um
H okay let me see if I can figure out
how to put some credits on the thing and
we'll we'll try to see if we can get it
do it do
anything okay so it was uh option 55 put
it on free play this thing will not play
anything that that Mech will not move at
all now so apparently that chips fake or
something else is wrong with it or
whatever so I'm going to have to pull it
back out I did order two of the chips so
I'll try the other one but the ones I
ordered it's is a huge huge huge huge
huge huge the hugest problem
when you're working on old stuff is you
can't freaking tell if the stuff's real
or not there's no way to know no nobody
reputable that sells like everything you
know so you have to kind of pick and
choose where you buy stuff so you you
always end up buying the stuff on
eBay and then you have to watch who you
buy it from so I bought it from someone
who's got really good feedback but I
mean how the hell does he know if the
thing's the right chip so if you're if
you're unaware they
basically in China they'll have a bunch
of 40 pin chips that are something that
people don't want so they'll remark them
with with a 40 like the number of a 40
pin chip that people do want and it
turns useless chips into chips that they
can sell for five bucks so the way I try
to get around that is I buy from people
in the United States but if they buy it
from China and then just resell
it there's no way I know
one so who the hell knows what that chip
is I think it's right and see here
here's the other thing
so I'm not mentioning any names because
I don't know it might be right it might
be wrong but now I have no clue so we
have no no way of knowing if the CPU is
trying to do its thing or or
what it just
uh you end up at a at a dead end because
you can't rely on any of the of the
uh um any of the stuff that you ordered
to absolutely for sure
be
um
be the right thing it's
resetting um so I went in and uh
initialize the disc too just to see if
it would go and try to read that disc it
won't do anything it won't move at all
so I'll pull it back out and maybe we
can try the other one but it looked like
it was the the same exact uh
brand okay we have been mailed some
other ones cuz I was under the
impression that those are fake they
might other ones they said
Taiwan
now I looked it up and
Intel see that I Intel never made
anything in
Taiwan and they sure held it make it in
1980 in
Taiwan so I don't know my assumption is
that other chip is probably bad now this
one I guess I should show you that
so these are the ones that I got so this
is Intel copyright 1980 and then on the
back it says
Taiwan well that don't seem
right so it may have fried a bunch of
stuff but we'll
see so this one says
Intel copyright
1980 has some numbers on the back you
have no way of
knowing right it's impossible to know
people hopefully this one's a real one
but maybe these were real I don't know
because it's impossible to
know so uh I'm going to put this in and
we'll see what
happens I'm chasing my tail here so I
put it in guess what it went back to
everything cycling the whole time which
is exactly what it was doing before we
replaced it
but I finally bit the bullet said I'm
going to have to break out the damn
logic probe so I set up the logic
probe these are the inputs and outputs
for
a p8c
31bh okay
now to be completely honest with you I
have no clue what I'm doing but I'm
trying to think it through okay
so this
sucker it gets a clock
signal uh on this Crystal lines 18 and
19 and guess what they're pulsing so I'm
getting a clock signal I've got a ground
where I'm supposed to have a
ground and I've got power where I'm
supposed to have the
power okay pins one
through eight
are Port
one I read in the data sheet what port
one is I have no clue they're all high
one's low
randomly okay pin nine is the reset line
it's low I don't know if it's supposed
to be low or high or what okay pen 10 is
rxd which I think means signal coming
in and it's chattering
away okay and then there's t XD which I
think means signal going
out it don't seem to be doing much but
whatever
okay int0 int1 are both
High uh and then all of these that are
that are different ports and stuff most
of those are high BL blah but over
here we have address 0 1 2 3 4 5 6 7
uh 8 9 10 11 12 13 14 15 and they're all
pulsing away so the chip must be
working uh 29 says
psen with a line over it who knows it's
pulsing 30 is the al- program with a
line over it it's ping 31 is EA with a
line over it it's
low okay so all of that's pulsing away
so I think the the Chip's working and
everything's moving again doing its
thing right so I think these other ones
probably were fake but the new ones
aren't so we're back where we were but
then it gets
better so then I moved back to the first
chip that we messed with in this video
or I believe it was this video by the
way I've been filming this for weeks uh
it's a 74574 so I did the same thing I
wrote out uh what the lines are supposed
to
be and so pin one is an outp put enable
line which if it's low it enables the
outputs this thing has a bunch of
flip-flops in
it okay so 2 three four five 6 seven8
and nine are inputs and they're all
pulsing pulsing away 10 is the ground 11
is the clock 12 13 14 15 16 17 18 19 are
the outputs but guess what the clock
signal is not
there because
because
somehow I have nicked the board see it
right there see that little
Nick it's right on the freaking line I
don't know how I did that I went back
and looked at the earlier video and it's
not on there so I did that somehow and
it's like the line is it's perfectly
nicked for cutting the
line how'd I do that I must have been
trying to pry the chip off the board I
should have cut it off and I wouldn't
had a problem when I follow this back
though I get to he and it's high but it
may be that's how it's supposed to be in
the state that I've got it in I don't
know because the clock and the output
enable and the pulses you know the info
sent all kind of tell it what to do but
that thing is definitely not connected
so I'm definitely going to connect it
back
um hopefully that'll do it so I'll put a
little jumper wire on it and we'll see
where that gets
us
okay so I put a little tiny jumper wire
on it you can go you can put a jumper to
a via if you're very careful one you
don't want to damage the Via but also
you
uh just because it's through it doesn't
mean it's connected to it so you have to
make sure you get it heated up plenty
that it uh on on these particular kind
of wire wraps that it melts the
insulation around it see it's sticking
through there right
there so if you get enough if you get
enough solder on there you're good to go
so hopefully that'll put that CL clock
back at least and um maybe that'll make
it work
better okay so I have put the board back
in I believe we have some
progress the row link Tex
TX light is blinking slightly you may
not be able to see
it the 5vt DC light is on okay the home
light is off the index light is
off I think those maybe are supposed to
be on though because it it should well
maybe not one of those should be on I
think because basically it should be at
the home position or the the whatever
those are those are like the switches
the CDM communication light is not on
and the scan transfer light is not on
the board error light is 9 one okay on
the
CCC the voltage light is on and the row
Link light is blinking doing a thing
okay now we are not on free
play so I need to put it on free play I
have figured out how to do
that so I put it into the service
mode I'm holding this all up with my
leg it says errors exist that's fine so
here's what you do five is the
pricing and then five is free play
status but then to set it you have to
hold reset and nine to change it from
off to on
so I did that okay and then you hit
popular to save that okay now when you
slide it
back it will hit the switch to turn it
from uh service to regular now it says
free okay so now we can try a
selection so let's say we're going to
play CD
35
track
12
okay so the scan transfer light is now
on but the home light is not on and the
index light is not on well I think the
home light did blink let me watch it
again yep the home light is
blinking the index light is not
blinking the CDM
communication light is not
blinking okay so I think our problem is
it can't tell where it is it's looking
for track uh
cd35 and it can't find it which probably
has something to do with that index
light so uh let me look in the manual
and see if I can figure out what's going
on with that but man do you see what
just happened here I pressed the
keyboard it talked to the
computer
that ain't good looks like it
reset yeah see it's doing it again so it
reset that's not good um but it the
keyboard talked to the computer which
talked to that to tell it to look for
this 35 but it can't find this 35 but
we're a lot farther along
now um so let me look in the manual and
see if it it's probably like there's a
sensor there it's probably that one
we're looking at maybe it's not uh
plugged in well or something although
it's see in the home
position I know let me look in the
manual okay so in the manual I don't
have the schematics for that newer
updated Mech board but the old Mech
board used most of the same plugs and
everything and it does use the same one
there is a LED for home and an LED for
index the home one appears to be working
but the index one isn't so that could
just be as easy as it's uh dirty so
we're going to try cleaning it and if
not we might be able to track it back
onto the
board pin one and pin four well pin one
must be working because the home one's
working pin two must be working because
the home one's
working um pin three must be working
because the home one's working so it's
just this index line that would be a
problem or the actual LED itself or the
whatever it is photo transistor whatever
it is
um so we'll we'll try cleaning that and
see if that makes the light come on now
remember before all the lights were on
but that appeared to be because the chip
was
bad okay so here is the sensor unit it's
all contained in one
piece but if you look there is grease
all over the inside of it so if it it it
appears that the way it works is it
shoots a
light from this side to that
side and then um as the gear teeth pass
through it it counts how many times the
light is
interrupted so it could just be that
it's misadjusted it could be that the
photo transistor in there is
is messed up or it could be that it has
grease smeared all over it so it can't
read the light or send the light so I'm
going to clean that all up and then
we'll put it back on there and see if we
can figure out how to adjust the
thing okay so all I did was clean it and
put it back on and the index light came
on and I I there's see that little thumb
wheel up there I was able to adjust
it it's height on the
gear right it's not touching or anything
but it must have just been filthy and it
moved around to number 35 but we're
going to try it let's see what do you
think now you know this we're two videos
Deep now we're already two videos in we
have to see if it's if it seems like
it's going to work so let's try disc
let's act like there's a
60 7
track
three holy
crap it's actually attempting to play a
CD looks like it knows that it's not
there it's going to try it
again
it hung it up all right so it probably
just told the computer hey that CD is
not even there all right so let's try
2020
8 see the index light coming on and off
now it's
on it seems to be on 22
[Music]
wow it's trying to play it it's not
playing figured it out hung it
up okay so I need to put the amplifier
back in it and then I'm going to slide a
CD in it and we'll see if it will
actually
play
okay folks we're going to try it out
what do you think I slipped a CD into it
now normally it would have
the I guess in the first video we
probably took that out with the uh the
pages right normally it would have the
pages but I have put a
CD now I can't play you the CD because
uh I'll get a copyright
strike but I can play you a little bit
of the CD they probably won't even know
what it is right
so I put one in
0
8 let's try
track
five is it going to play oh it got it is
it going to play is it going to
[Music]
play yeah
[Music]
[Applause]
[Music]
yeah maybe we put it down real low maybe
we put it down real low when I talk they
won't be able to tell that it's
playing all right so that worked out
pretty good so basically it was the uln
2003 chip and then that one before it
which was what the
745 what whatever we were just messing
with I think both of those were bad but
I screwed up when I soldered the thing
back in I missed that I messed that one
Trace up and so by messing that Trace up
it took one of the control lines off of
it which basically had had made that
chip where it was just constantly
outputting when it shouldn't be so it
was making everything connected to it
work all of the LEDs that were connected
to it uh the motor that does the
scanning the motor that does the Gear
the and the reason it was doing that was
because it was turning this little
switch over here on the left and so by
the time that it took that to turn
around one turn you got five
more CDs over or whatever so that's why
it looked like it was doing some kind of
pattern it was just that little piece on
the side turning which was just turning
because all the outputs were enabled but
I think we're good now now obviously the
thing still needs a whole bunch of work
it needs me to uh like there might be a
couple lights out down there we have to
put 100 CDs in it before we sell it
that'll take a little while right the
amp sounds pretty good though so I don't
know that we have to do much there um we
got this from a gentleman who said that
it was working in his house and then
quit but guess what that's what
everybody says so we didn't know for
sure but I think we're uh I think we're
looking pretty good on it so we we'll
probably do another video of it actually
playing and we'll play a song for you
and just make it a separate video so
that uh you can listen to it and uh we
don't we just won't care that it uh
basically demonetizes us on that one
video so leave your comments down below
let us know what you think have ever
worked on these cd1 100s and you were
laughing the whole time cuz I didn't
know what I was doing you know what I
might not know what I'm doing but I got
there didn't I huh huh huh
huh it's good to see something I love it
when a beautiful plan comes together who
said
that but um leave your comments down
below let us know what you think make
sure to give us a thumbs up and uh we'd
like to thank everybody that's been
using our Amazon links if you don't know
about that down below below there is a
link to Amazon for your country or a
country near you and so if you click
that it takes you to Amazon and anything
you buy on Amazon it gives us a little
tip for sending you there so we
appreciate that if you're planning on
buying anything from Amazon just click
our link first that's all you have to do
uh and then also we'd like to thank
everybody that's been uh watching and
subscribing to my brother Donnie here on
YouTube who's literally my brother
Donnie uh he and I have been working on
this old uh dilapidated grocery store
lately that we bought in a small town
near here
and uh we've been fixing it up so that
we can rent it out and uh we're about
done with it so everybody that's been
watching the video uh the videos on that
we appreciate it now if uh if uh you're
interested in buying or seeing any of
the tools that we use and stuff not
necessarily on this video but on some of
our other videos If you go to our
website we have a new page up on our
website that shows kind of like some of
the things on Amazon that we use uh on
our repairs uh for like the pinball
machines and stuff like that and we also
have links on there to our t-shirts and
coffee mugs and all that good stuff if
you want any merchandise with Joe's
video games on it so I think we're
looking pretty sweet man let's do
another
one I don't really this CD was just
laying around folks I'm not a big fan
I'm not not a fan I don't hate on the
guy I'm just saying I'm not a you know
I'm not a big not a big fan
that's a good
one
uh
uh
uh
uh uh that was the big
one let's let's uh let's
start days like these that sounds
good oh automatically I accidentally
started it ain't
easy I
I
all right so I'll turn it up and then
I'm going to turn it off because I don't
want them to give me a copyright strike
but you'll hear at least the beginning
of
[Music]
it
