Couplet Leather Cardholder Tutorial

Carving and making leather goods
49 followers
Hey everyone, this is Thomas with TC Haul Leather, back again with another tutorial.
This one is for our Couplet Cardholder Pattern. It is free on our website,
the link's in the description. Everything you need should be there.
Today we're using black and violet Botero leather. Really fantastic stuff, very dense
with a bit of sheen to it. It can be a little tough to cut if you're not experienced with
this kind of leather or if your knife isn't super sharp. So make sure to give it a good
strop before you start. Here we're just cutting out the pieces that we have outlined with our
scratch awl. You can print your pattern on paper and then tape it or glue it to some cardstock or
some cardboard. That gives you a reusable pattern. We have 150 grit sandpaper for sanding the edges
and what you'll see me doing with these pocket pieces is trimming off just a little bit of the
thumb slot. That way when we sand it, you don't have a sharp edge. Our next step is going to be
creasing our pockets. We have a cheap Amazon special creasing tool here, heated by a candle.
Very high tech. If you don't have a creasing tool, that's okay. It'll look just fine without it.
Next, we're going to bevel our edges on the pocket panels
and grab some Tocanol. If you don't have any Tocanol, it's just a burnishing agent,
water-based. You can use beeswax, water, or gum triglycerides. All work relatively well.
I just prefer Tocanol by Silo Leather Company. We use them for a lot of our products.
A couple of notes while I'm making my Maker's Mark stamp here. We do have trim allowance on
the pattern, and the trim allowance really allows you to cut away the pieces of leather
you don't want, and it gives you a perfectly smooth edge. So what we're doing here is
marking out on the back of our pocket panels where the glue is going to go. We line up the
pocket panels and use a scratch awl to get the best alignment possible. Before gluing,
you always want to rough up the flesh side of the leather, especially with something as shiny as
Botero here. This is a roughing tool that's going to help us out with that. If you don't rough up
your flesh side, the smooth side of the leather, that glue is going to come right off, and it's
going to be really unfortunate. Here's our leather glue. It's water-based from, again,
Siwa Leather Company. It has a really good set time that allows you to work with the leather,
but not so long you need to use a hair dryer. You don't really want glue to be squelching out the
edges when you push these pieces together. However, it is better to have more and not need it than not
have enough and have to add it later. That creates issues when you're sewing. As the needles go
through the leather, they can actually pull the pieces apart. We'll be using a roller tool here
that's going to help us get a really airtight seal between our pieces of leather. If you don't have a
roller tool, you can just press it with your fingers. You can use a bone folder, whatever works for you.
I mentioned earlier that our pattern uses trim allowance. Our trim allowance is going to be two
millimeters, so that's what I'm marking on the inside of our pocket panels. When we cut
that two millimeters off, we're left with a really smooth and glued, cured surface.
We use the slanted pricking irons from Rocky Mountain Leather Company. They're 3.85 millimeters.
This is the 9-tooth version. We also have a 2-tooth that lets us work around corners.
Anytime you make holes in leather for stitching, you want to seal up those holes a little bit
with a bone folder or a hammer to make sure that they stay as tight as possible for as long as
possible. Here's our Vinimo MBT thread. This is number 5. It's 0.6 millimeters black.
I did use some beeswax on it. It helps to slide through the leather and not kill your fingers.
Double check to make sure that both sides of your thread are equal, then you can start stitching.
I always do at least one backstitch when I start and when I finish, but that's up to you.
When we get to the overlap of the pocket pieces, we're going to make another backstitch just for
reinforcement. We snip off the thread on both sides and we're using a thread zap to melt that
polyester and pound it flat. I have to excuse my dog rolling around in the background.
Here we bevel our edges. Once we burnish this side panel with the wood slicker, you can see
how the toconol really helps that butero to take on an almost painted look. It's just so smooth.
We're marking out where the pocket panels go with a pen,
then aligning everything and making sure that it all matches up.
We switch our wing dividers to 6 millimeters. That's going to account for our 2 millimeter
trim allowance and also the 3.5 millimeters for our gluing and stitching. Sometimes when you cut
these oversized pieces with the trim allowance, you don't cut every edge perfectly and that's okay
because we have a trim allowance. So when you do trim off that edge, you can think like a
woodworker and give yourself one true edge to base everything else off of. As long as the edge that
you choose aligns with the tops of those pocket pieces that we really can't move anymore, everything's
going to be fine. Do yourself a favor and don't try to take this trim allowance in one pass.
We've got about 7 ounces of leather here, 3 pieces of 2.5 ounces, and if we try to do that in one go
with a knife, I would probably leave it looking like a wavy mess. Coming up here, we have our
radius tool. This thing's super useful. The more cuts you do with the radius tool, the smoother
your corner is going to be. We're sanding this down with 150 grit sandpaper. Then we're going
to use our wing divider at 3.5 millimeters, just like we said earlier. The most important
thing to remember here is to align your stitches on the line. As long as all of your stitches fall
on the line, they'll be straight. When you get to a pocket panel or two pieces that overlap,
you might find yourself with a little extra space. You can fudge it if you need to by moving
your pricking irons forward or backwards in the holes you've already made. My rule of thumb for
the amount of thread that I need is roughly 4 to 4.5 times the overall length of my stitch line.
If you have super thick leather, you might need more than that, but 4.5 times is a good starting
place. Remember to beat those stitches down so they don't get caught on anything and come unraveled.
We're giving it a final edge crease here before we bevel everything else.
We'll apply some Tocanol. Give it a good rub with the wood slicker.
Sand it down with a higher grit sandpaper. Remember to go from coarse to fine with your
sandpaper regardless of what grit you use. The next application of Tocanol is much lighter than
the first. We really don't need very much at all. Finally, we open up those pockets with a bone
folder. You clear out any excess glue or tightness and we're ready to go. I really hope you enjoyed
this free pattern and tutorial. We have lots of other patterns on our site as well as all of our
products custom and ready to ship. Please let us know if there's anything we can do to help,
or if you have any questions about this pattern or others that we make, or if you just want to say
hi, you can hit us up on Instagram, in the comments, on Facebook, or anywhere else. Thanks everyone!
