Artisan barrels. Traditional manufacture of this container for wine | Documentary film

Amazing Traditional Craft
29 followers
The ancestral vitivinicola tradition of the Vallisoletana locality of Nava del Rey
aroused the flourishing of workshops and industries
that seek the necessary tools for the production of wine.
Since 1941, the Burgos tonnage has played a fundamental role.
It provides the oak barrels that, over the years,
will turn the must into good wine.
The demands of the times have motivated the industrialization
of the process of making tonnages.
But Mariano Burgos retains fresh knowledge of the past
and recreates the artisanal manufacture.
It begins with the making of the duels,
the boards that will shape the barrels.
In principle, I am going to measure the duels.
Then I am going to hold it a little so that I can close it well.
With the hand saw, Mariano cuts the imported wood from the United States
to the exact measure that the barrel body will have.
Now we remove it, and this is a board, and I am going to turn it into a duel,
making the figure on the outside and the figure on the inside,
in this other bench that is prepared for that.
With the help of the flat blade, the barrel maker
carves the outside of the duel on both ends,
tracing the fall and giving it the appropriate inclination,
so that later they fit together.
The inner face is worked with the back blade,
ideal for shaping the belly of the duel.
Now it is going to go to the other, to the deck, to put it together.
In the deck, Mariano Burgos fine-tunes the duels and equals each of their surfaces.
Now I am going to take the square to see that the angle is correct, of the barrel.
The craftsman will repeat this process about thirty times,
until he obtains the number of duels necessary to make a barrel.
This is the last one. I think with this I have more or less to make a barrel. I understand that yes.
This is the armorer, it is to measure the top head to put it upright on the barricade.
This is the board to put the first duel on it, so that it does not fall.
The barrel maker assembles the barrel by alternating duels of different sizes,
wide and narrow, placed so that they fit perfectly.
And now the last one, we remove the board,
to make the measure that fits, and it can be this.
This is the third, the first ring that we put in after the pipe is standing or armed,
to hold it a little. Then we give it with the hammer and tighten it a little.
The third is one of the molded rings that are placed so that the barrel obtains its curvature.
And then I put the board to put it straight. I remove the armor and put the board.
With a hammer and chisel, Mariano tightens the rings so that the duels are correctly fixed
and remain immobile in later processes.
In addition, he aligns all the heads of the duels, so that later it is easier to work.
That's it, now I'm going to put the barrel, to tighten it well.
The three provisional rings, testero, tercio and barrigal, are placed in the same way.
They must be tight and that is why Mariano constantly hits them,
until his experience tells him that it is enough.
Once the barrel is assembled, we will proceed to take it.
Then we put the fire, which is the first thing.
The fire is fed with the virutas of the oak wood used to make the barrels.
When the flames are already generous, the craftsman places the armed barrel on top
so that it begins to take on temperature.
In about twenty minutes, he acquires the exact degrees to be able to tame it.
The lathe will be his best ally to slowly tame the barrel body.
Mariano helps himself with a board to place the saw of the lathe around the lower part of the duels.
This is on, now I am going to wet it a little so that it helps me and gives elasticity to the wood,
now that it is already hot.
The tonneler wets the barrel once it is hot, so that the water and the fire harmonize
and prevent the duels from breaking or fraying when bent.
It seems that the wood is getting darker, it is changing color,
and that tells us that it is going very well for taming.
The tone of the wood indicates that its strands are already docile and can be bent easily.
Water, fire and the hand of the man intervene so that the inside of the duels
shrinks and the outside stretches.
The tonneler thus acquires the punchy silhouette that characterizes it.
Now I'm going to finish closing it.
And then, as it loosens up, I'll tighten it a little here.
That's it. Now you have to tighten this a little, the upper rings.
The molded rings have loosened due to the pressure exerted by the lathe.
That is why Mariano uses the hammer and chisel again to hold them to the perimeter of the barrel.
Now we are going to return it to put the rings on the other side.
The rings that are in another place.
I'm going to put the barrel to start tightening it around here.
Now I'm going to put the third.
Once the third is quite tight, the tonneler removes the lathe,
since the rings themselves exert the pressure that the body needs to maintain its punchy shape.
Now I'm going to take the tonneler and take the three,
because one will loosen as I put the other in.
The rhythmic blows of the hammer and chisel
are a constant in the work of this artisan master.
It is essential that the rings are well fixed,
so that the following works are effective and profitable.
I'm going to start making the head. I have the camera ready, I'm going to put the barrel.
And now to start.
Now I'm going to start with the big sole.
This tool is used to lower the heads of the rings,
while giving them a slight inclination inward.
In this way, it will be easier to insert and fit the bottoms of the tonnel.
Now I'm going to use a rope to put the head straight.
Mariano uses a small fork to straighten all the heads of the rings.
The head of the barrel will be completely aligned and free of protrusions in this way.
Now we are going to clamp it inside, to make the shape inside to make the back ring.
That has been finished and I am going to make the ring for the slot to put the bottom, which is this device.
Now I'm going to put it to size and then I'm going to start working on the ring.
The chisel is the tool that Mariano uses to make the ring,
which is the slit in which the bottom or the lid of the barrel will be placed.
And now I'm going to remove the rods with the small sole.
The tonneler refines the head of the barrel with a chisel.
In addition to the small sole, he uses the chisel to finish off the ring,
so that the slot is clean and well defined.
The same process is carried out on both ends of the barrel, to be able to cover it hermetically.
I'm going to make a bottom and it has to go through the same process as the long boards.
I brush the face with the small brush and then I put it together.
And now we are going to put it together with the large claw, taking the right angle.
Mariano will repeat this task up to eight times, the number of boards he needs to assemble the bottom.
Now we have the eight boards made here.
We are going to join them to make the complete bottom.
First we are going to take measure of how they have to go.
Now they can be nailed from number one.
They are put in the lathe
and they are nailed, taking into account the center.
Here, so as not to mark them, you have to put a little bit back to give.
The tip has a tip on both sides.
Then one is nailed in the bottom and the top.
Once the boards are nailed,
the tonneler calculates with the compass the measure that the bottom should have
and makes an exact mark on the boards.
Now we cut it with the saw.
Then, Mariano conscientiously brushes the bottom with the hand brush.
We brush a little on the outside.
Now I am going to make the chaflán, which corresponds to making the hole in the bar.
Now we are going to do it, we are going to put it in the lathe to cut the interior chaflán.
We are going to do it in crude, it is a little flour and water,
as you can see, to give the bar a grip so that the bottom sits well in it.
This craftsman distributes the engrudo, the paste that will act as glue,
throughout the slot where the bottom will be placed.
Everything has been engrudo, now I am going to put the bottom in.
I take the hammer, the chazo, I loosen it,
I am going to mark the mouth of the bar so that the bottoms go straight to it.
So I have to mark it beforehand so that it can be,
so that the bottoms can go straight to it.
That is the mouth.
The tonnelero places the first bottom without more help than his hands.
To make it well held, he hammers it and puts the molded rings again,
which will exert the appropriate pressure,
so that the union between the gargoyle and the base is inseparable.
To put the second bottom, Mariano performs the same operation.
He extends the engrudo in the gargoyle,
removes the tertio and testero rings and places the base.
This time, the action entails a new difficulty,
the tunnel is closed on the other side
and therefore needs the help of a cast iron to place the lid.
Immediately after, he reassembles the rings in their place
and squeezes them with a hammer and chazo.
The sound that emerges when hitting the outer part of the bottom
reveals that the tunnel is hermetically closed.
This is fine, we are going to knife now in the goat.
First we are going to remove these rings, the rings on one side.
Then we put it on the goat and start to knife.
Now I am going to make the measurement of the ring,
the measurement where it will go in the barrel,
because they have to go to the measurement,
and then the ring to its measurement, for the barrel.
Then we put the others.
Now I am going to proceed to measure.
I am going to the gargoyle to put the rivets of the ring,
with a pointer and a nut.
And of course the rivets.
In the yunque or bigornia,
Mariano marks the point where he will place the first of the rivets.
The hole of a nut serves as a mold to make the perforation,
hitting with the hammer and the pointer.
You can already put the rivet with the help of the hammer.
Each ring has two rivets,
so the craftsman repeats the process several times.
The definitive rings finally replace the molded rings.
The rivets must be perfectly aligned with the mouth of the barrel
so that the result is harmonious.
As a colophon, the rings are hit to smooth out possible imperfections.
I am going to measure the center of the barrel to give it the mouth,
with the bigornia that we have there.
The barrel manufacturing process is coming to an end.
Mariano spins the barbiquí
to make the hole that receives the name of the mouth.
With a fine chisel, he goes over the entire perimeter
so that it is smooth and without splinters.
The barrel is finished, now we just have to fill it with wine.
The best broths acquire their qualities in barrels like this one.
The degree of toasting of the wood determines the aroma and flavor of the wine,
from coffee or vanilla to the characteristic fragrance of the leather.
Mariano Burgos belongs to the second generation of barrel makers,
and his sons and grandsons have already inherited the knowledge
to provide the best containers for the breeding and aging of good wine.
I am Eugenio Monesma, director and producer of the documentary you just saw.
If you liked it, I encourage you to subscribe
by activating the notifications from the bell
and so you can enjoy the hundreds of documentaries
that I already have on the channel and of which I will be uploading weekly.
