Standard vs Upgraded Ute Suspension Test! How to choose the right springs for your 4WD

Automobile Identity
371 followers
#automobile #autos #cars #4wheels #luxurycar #sportcar #highspeedcar #testdrive #toyota #tesla #porsche #hyundai #rollsroyce #royall #suvs
Here are some expert suspension tips you need to know
to get your four-wheel drive set up properly
for carrying what you need to carry.
To do that, I'm back down at Tough Dog's R&D center.
I'm going to be chatting to my good mate, Simon,
who has been building suspension here
in the R&D team for 30 years.
So it's safe to say he knows what he's talking about.
Let's get into it.
Okay, so you need to do something
about the suspension in your ute.
Where do you start?
The very first step is to figure out
everything you need to carry
and how often you're going to carry it.
The reason why your four-wheel drive is riding rough
and a huge contributor to a bent chassis
is choosing the wrong spring rate.
Today, we're going to put different spring rates
in this Ford Ranger under load
to show you exactly what happens
and give you the right information
so you can choose the right spring rate
for your four-wheel drive.
To show you what happens to your suspension
if you load it up with the incorrect spring rate,
we're putting the standard Ford suspension
back in the Tough Dog Ranger.
Then we're going to put the canopy on
and Simon's going to point out everything that's happening
to that standard suspension
and why it's no good if you want to load your ute up.
Then we're going to pull these springs out
and put the correct spring rate in,
show you the difference and why it's much safer
and it'll be better to drive.
Here we have the factory spring fitted in place.
And what you'll notice is the three primary leaves
are now fully engaged on the second stage.
And also too is the bump stop.
It is now fully engaged on the axle.
Now what that actually means is
this axle cannot compress any further
than what it has done here.
As a result of the spring being fully compressed
against the bump stop,
there would also be some pretty dynamic forces
going through the chassis rail here
where we're fully engaged.
By fitting the correct leaf spring,
it allows to restore the bump stop gap,
allowing the axle to move up and down,
which is the design of the vehicle.
At the moment what we have here
is a vehicle where the axle is tracked
between the weight coming down onto the spring
and the bump stop, which is engaged on the striker plate.
While restoring the bump stop gap,
it will also improve the vehicle's performance in braking.
The reason why the braking performance will be affected
by an axle that is trapped against the bump stop
is mainly due to the axle
hopping and fighting against the bump stop,
almost causing like a slapping effect.
We now have the 500 kilo constant load spring in place.
And the one thing that you'll notice
is we're now maintaining a 70 to 80 mil bump stop gap,
which is super important.
We also have doubled the amount of leaves
in the primary stage and also in the secondary.
And the primary stage is now just resting
on that second stage just for that extra support
so that we're not W-ing the spring over the second stage.
Droop being the axle falling away from the chassis,
and it's super important to maintain
that 60 to 70 mil of droop from ride height.
We've put a yellow indicator mark here
just showing where the shock absorber is sitting
at the moment with the correct spring fitted in place
and the correct load placed over the axle.
The important part about this
is ensuring that we have the correct spring fitted
for the weight being placed over the axle.
If the spring was too powerful,
we certainly wouldn't maintain the 70 mil of droop
that we have here now,
risking the shock absorber to be frequently topping out.
Topping out and bottoming out your shock
can happen if you fit the wrong length shock
to your vehicle relative to the height increase
of the springs you've put in.
For example, a shock that's too short
with an increased suspension height
will be sitting almost fully extended at ride height,
which means it's always working at the end of its range
and you can damage the shock.
Whereas fitting a shock that's too long
for the springs you've fitted
means it will fully compress before the bump stops do,
which can also damage the shock.
Your shock essentially becomes your bump stop.
That's why it's essential to get the right length shocks
to suit your vehicle at full droop of your suspension
and full up travel.
Okay, so we've explained choosing the right spring rate
for load carrying,
but how does that affect flex and off-road performance?
We're out on the tracks because we want to show you
that even if you get heavier duty springs,
you're not going to lose articulation
provided they're matched to the weight of the vehicle.
So here we have the Next Gen Ranger
with the Tough Dog suspension kitted in,
raised 50 mil.
It has a zero to 300 kilo spring.
Springs matched perfectly to the tray.
As you can see,
we've taken that spring now to full articulation
and the shock is at full travel.
Really important to match the shock absorber
to the leaf spring so that we ensure
that neither of them run out of travel
in the way that they're supposed to.
And as you can see,
it's the shock absorber
that's limiting the wheel travel here, not the spring.
So it's a bit of a misconception
that by choosing a constant 500 kilo spring,
that it limits the down travel.
And in fact, that couldn't be further from the truth.
It's actually the shock absorber
that dictates the full droop travel.
So as you can see here,
we've got a zero to 300.
We've got a tray fitted.
We're at full travel here.
Everything is well protected,
brake lines and ABS lines.
And on the other side,
we have full compression stroke
on the bump stop the way it should be.
So what we're saying is the right spring and shock combo
should mean your droop is only limited by your shock length
and your compression is limited by your bump stop,
not your shock topping out
because that's what can cause them to wear and fail faster.
Next up, we wanna talk about the difference here
between the good old coil spring and the leaf spring.
Coil spring here being made in Australia,
we're using a micro alloyed steel.
Important to note that the way we come up with a design
for a coil is not just by the free length,
it's also the thickness of the coil,
the pitch between the wire and also the free height.
One of the other misconception
is running a really tall coil
and allowing that coil to come down
to the correct ride height.
And that will cause a lot of stress on the coil.
And not only that,
we wanna ensure that the coil spring doesn't bind
before the internal bump stop comes into play.
A sign of that could be chattering in between the coils
where perhaps the powder coat's been fractured
from the coil spring binding.
So again, we don't wanna just run a super long coil
and have that compressed down to the correct ride height.
It will always come down to matching the correct spring rate
to the vehicle's application.
What we have here in front of us
is a next gen Ranger comfort spring.
You'll notice that it has a delete on the second stage,
just purely running primary leaves.
And the idea of this is just to keep the leaf spring
nice and linear all the way to the bump stop,
just ensuring comfort.
And again, we're giving the customer three choices here
with leaf springs being, this is a comfort spring.
We also do a constant load 300 and a constant load 500.
And that's where we see the second leaf coming into play
to support the primary leaves.
Keeping in mind, if we were going to a heavier application
where we're seeing a canopy or a steel tray,
this is where we would introduce the load leaves
to support the primary leaves.
Just so that we don't have the spring laying out too flat.
So as we've seen, this is a single rate spring,
nice and linear all the way down to the bump stop.
Now, if we were carrying things
like a steel canopy or steel tray,
we would option up for the second stage spring.
And again, it's super important selecting
the correct spring for the application of the steel tray.
It's always been a bit of a misconception with airbags,
when to use them.
Do they make the ride too firm
or do they restrict the wheel travel on droop?
So I thought we'd cover off today
just on a few things.
Firstly, the old poly bag here made from polyurethane
and designed to go inside the coil spring.
It would run this coil as a minimum at five PSI
and as a maximum of 60 PSI.
The idea of this bag is just to top the spring right up.
So if you chose a lighter rate coil
or if you had the factory OEM coil
and you're carrying an inconsistent load,
this bag would be the ultimate solution.
The important thing to note with the poly bag
is that you take the bag
to a maximum pressure of 60 PSI first
before placing the load over the rear axle.
And then taking air out of the bag
until the desired ride height is achieved.
Because we want the bag to actually grow in height
rather than grow in width
and being trapped in between the coils.
The Bellows bag is a rubber constructed two-ply bag,
comes in different heights.
We do a standard height application
and a long travel application.
The bag should only be used to top up the spring rate,
not to carry the complete load.
Carrying that can end in,
well, we've seen that plenty of times now
with chassis rails being damaged.
The poly air spring is a great solution
for vehicles like this Ram behind us here
where we're inconsistently loaded.
Back of the vehicle here might be taking
say 200 kilos of cargo.
And due to the lighter spring rate,
the poly air bag is a perfect solution.
We can take the bag to 60 PSI before the load goes on
and then lower the PSI back down to the desired rake.
Now rake is how much higher the back of the vehicle is
than the front of the vehicle.
And ideally what we would like is the back of the vehicle
to be around about 15 mil taller than the front.
And also ensuring that the headlight trajectory
is facing the road rather than the trees.
In summing up, you can see why spring rates
are so important for your vehicle.
Hopefully this video has given you the information you need
to get your spring rates right.
If you get them right,
your vehicle will drive nicer,
be able to carry a load much safer
and generally be much more enjoyable to cruise around in.
Of course, if you're not sure,
you can give the experts at Tough Dog a call
and they'll be able to sort out
your suspension spring rates perfectly
for your four wheel drive and what you use it for.
Thanks for watching and I'll catch you next time.
