How to: Fix/Repair faded flaking damaged Clear Coat Paint - Part 1

Auto Retech
2 followers
Welcome back to the 6th Gear Garage. Today I'm going to show how to prep
and repair this faded clear coat on the $350 Acura Legend.
So this car came from out west and you can see it had a hood bra for most of its life.
The paint still looks great on the front of the hood,
but then look what years of UV rays and neglect did to the rest of the hood.
This clear coat isn't just faded. Parts of it have completely delaminated and flaked away.
Once the UV resistant clear coat is gone, the color coat underneath begins to fade from the sun.
So instead of just re-clearing, now I need to re-spray areas of color coat as well.
The clear coat is bad on the roof too, and just really filthy in general.
This car did sit for a decade before I bought it.
When the clear gets to these white splotchy areas,
it has completely delaminated from the color coat.
The only way to fix it at this point is sanding off the damaged clear and re-spraying.
So the hood, fender, roof are bad.
And the top of the doors.
But look at the trunk. No delaminating of the clear coat on the trunk lid.
I think I'll be able to bring this back with some polishing.
The top surfaces soak up all of the UV rays. The sides are fine.
What do you think about these Enkei EK90 wheels?
Yay or nay?
I'm doing a quick test getting the faded clear coat wet.
I can still see some splotchiness on the roof.
Still see it here on the fender.
And of course, it's really bad on the hood.
A coat of water on the paint shows what it would look like if I just
spray clear over the existing surface.
And I can see that's not going to work.
There's a line here where the bra was.
It's not just the clear that's faded, it's the red as well.
Now that it's wet, I can tell the rest of the hood is a little more pink.
Then of course, it's really faded where there's no more clear.
First, let's give it a bath with some dish soap.
If there's any wax left on here, this will take it off.
Found a helper.
He works hard for 15 animal crackers per hour.
Now this is what the paint is going to look like when I'm all done.
Check out the trunk with water on it.
That's good news.
I bet I can bring this back without having to re-clear it.
If it looks this good with water on it.
Some kind of mold on it.
The water is starting to dry and it's back to doo-doo finish.
I pulled in the garage where there's better lighting.
And I can see all kinds of crud on the paint.
Like this.
And this.
So I have an old clay bar here.
Almost out of spray.
Used most of this on the Mustang.
But any other detail spray should work as well.
This has to be like 15 years old.
Clay bar will help remove the contaminants from the surface before I start working on it.
Spray on some lube, aka detail spray.
Then rub the clay.
Working in maybe a 2 foot by 2 foot area.
This spot isn't coming out.
Let's take a look at what the clay bar picked up.
Look at all that crud and debris.
I'll do the rest of the hood off camera.
I did half of the trunk lid.
And if you look really close.
Focus.
There's all kinds of white debris stuck to the paint.
And it's all over the place.
There's this black stuff again that doesn't want to come off.
I don't know if this is like a mold or mildew.
But it's all over.
Some of it came off.
It just took some elbow grease.
That's getting better.
More scrubbing.
Alright, I did the whole car with the clay bar.
This can all be polished out.
So can this.
The area under the hood bra could be saved.
But the rest of the hood is gone.
You can see this is actually the color coat on the clay bar.
It came off in the area where the clear is missing.
So the hood will need color and clear.
Same for the roof.
It's going to need some color touch up in some areas.
Then the whole thing recleared.
The clay bar leaves this slurry mess.
But it comes off with a good wash.
Alright, I pulled the car back in the garage.
And I want to show you something under these lights.
Right now the surface is wet.
Water doesn't bead at all because there's no wax at all in this paint.
But how it looks wet right now is exactly how it would look if I were to just clear coat as is.
You can see there's a night and day difference on the areas
where the clear coat is completely gone.
And that's thanks to the color coat fading without that UV protection from the clear coat.
Red actually fades the most from UV rays.
That's why some red cars turn pink as they get old.
So I'll need to spray some fresh red on the hood.
And on the roof.
But most of the roof is fine, so I'll try to blend it in.
Here too.
Top edge of the doors.
And part of this fender has the clear delaminating,
so I'll need to touch up the red on that before reclearing as well.
Passenger fender looks good.
I think I can bring that back with paint correction.
Since I was going to be doing color and clear already,
I took some time to repair scratches on the bumpers and get them ready for paint.
I already have a full video from the $500 Toyota Camry
where I showed how to repair a damaged bumper and paint it to match.
So I'll put a link to that how to in the description to try and keep this video short.
Since I'll be doing the top edge of the doors,
I'll just pull off this trim.
Given the choice of masking off or removing trim,
it's always better to remove it if you can and avoid a tape line.
This trim is in rough shape anyways, so I'll restore this in a future video,
getting it looking new again before I put it back on the car.
Hey, we are back at it.
Had to take a break to work on another project.
I just gave the car another bath to wash off any dust or dirt from sitting in the pole barn.
And today I'm going to be doing some wet sanding.
I ordered some wet or dry sandpaper. I'll put a link in the description.
And this is 800 grit.
I have a couple sanding blocks here, but for this job I'm going to use these two.
We'll look at those in a minute.
I'm going to be wet sanding the entire surface with the 800 grit paper, including this area.
This needs to be a smooth flat transition from clear to no clear.
I'm going to do my best to blend all this with red touch up aerosol cans
before I re-clear the entire hood. Same with this fender.
And roof.
The tops of the doors are delaminating.
All these areas need to be sanded with 800 grit.
For a flat area, I'm using this stiffer block.
This flexible sponge is better for curved areas.
Just wrap the paper around the block and dunk it in the water.
Then start sanding back and forth.
You can see the water is turning white.
That's the clear coat being removed from the 800 grit.
Look, I've got some color on there too.
That's from the area that didn't have any clear coat.
Give it a dunk every minute and drop some water on the surface to keep things wet.
It's good to switch up the direction too.
It seems to sand a little faster and more evenly.
You can see all this pink water.
That's the red color combined with the white clear.
I want to make sure I get this delaminated area all the way smooth.
It can take a while.
The paper loses some grit after a while.
So I'm flipping it around so there's a fresh side facing out.
And that'll have more bite than the used area.
Now 800 sands kind of fast.
The lower the number, the more abrasive it is.
If the paper is too low, it'll leave scratches too deep that won't be filled in by the paint
and you'll see them when the paint's all done.
If I use too high of a grit, there won't be enough scratches in the surface for the
new paint to bite to and I run the risk of the paint not bonding well and peeling in the future.
So 800 is kind of the sweet spot.
Take a look at this.
This is the factory primer showing beneath the red.
The color code isn't very thick on most vehicles compared to the clear.
And that's alright because I'm going to spray more color.
But if your clear isn't delaminating like mine is,
then you don't need to respray the color before applying new clear.
So you don't want to go this far.
The transition and the delaminated area is feeling pretty smooth now.
I've got these tiny spots that still need sanded though.
I've almost sanded them out.
Watch this.
And they're gone.
I've got a few more down here.
The tiny spots are starting to delaminate so I can't paint over it.
Because eventually it will get worse and lift from the base
and cause the new paint on top to peel off with it.
It is a lot of work and elbow grease to do this the right way.
This area in the middle here is good to go.
It looks like there are still dots,
but they aren't white dots where the clear is lifting.
It's actually those areas of delamination where I've sanded it smooth
and now you can see where the color has faded in those spots.
So feel it with your fingers because although it may not look smooth,
it might be perfect.
Like all this is smooth even though it looks splotchy.
This does make a mess.
Strawberry milkshake.
Now I just have to sand the rest of the hood.
When it comes to these curved areas of the hood,
I can't sand these evenly with a rigid block or else I'll only sand the top edge.
That's where I'm going to use this flexible sanding sponge that I showed earlier.
Wrap it up just like I did with the block and it flexes to match this contour.
I'll have links in the description for the sanding block and this sponge.
Just go back and forth in different directions.
Don't forget the very corner.
Just be careful on edges because they're very easy to sand through.
It's natural to apply more pressure on an edge or any raised area that isn't flat.
I'm actually using an older piece of 800 grit right now
because a used piece of sandpaper doesn't cut as fast as a brand new sheet.
That kind of gives me a little more room for error.
This back edge rolls over so I'm very lightly sanding that contour,
being careful not to go through.
But it does need to be sanded for the paint to bond well.
It doesn't take much pressure when there's so little surface area.
One more pass with my fingers just in case I missed any areas with the sponge
and the very corner.
Clean this off a little and let it dry.
Ok, this is dry now and you can see, well my finger is wet.
If you look close, you can see a thin line on the edge that didn't get sanded well.
It looks a little darker because it isn't scuffed up.
I'm going to hit that part real quick with the 800.
Everything has to be sanded so the new clear coat will stick.
I couldn't tell when it was all wet, but once it dries,
it's easy to see any areas that didn't get sanded well.
And again, I'm doing this with old dull paper,
so it's less likely that I'll sand through the raised edge.
Throw some water on the hood and I can use the sponge as a squeegee
to remove some of this sanding residue and dry the surface.
And that will help me see if I missed any areas when I sanded.
I don't have a drain in my garage and I don't want to wash it outside every time.
Alright, here's the worst area.
Now all cleaned up, completely sanded smooth with the 800 grit paper.
Notice there's no glossy area showing.
It's hard to tell if you missed any parts when it's wet,
but when it's dry, you'll be able to tell if you missed any area sanding.
Because it'll be glossy.
Like this.
I put a piece of tape on the top edge of this fender to protect it from the sandpaper
because I'm not reclearing it.
This way I can sand all the way to the very edge of the hood
without having to worry about accidentally scuffing up the fender with 800 grit paper.
I did the same thing on the driver's door here,
so I can sand all the way to the edge of the fender.
If you look really close, you can see there's a shiny area
on each side of this thin scuffed area.
Those are both low points that the block doesn't contact.
The clear coat comes up a little higher near the very edge.
I'll have to sand that part with my finger instead of the block.
The rest of the fender is coming along.
Right here it's shiny.
I was being careful not to sand the edge too much and I didn't sand it enough.
Anywhere it's shiny, the paint won't bond well.
Right here too.
Look over everything in a well lit area.
I gotta knock that down a little bit more.
Right now I just sanded down the factory orange peel.
Then I sanded the entire roof with the 800 grit paper.
Did I mention this makes a mess?
I got the hood done.
Roof is done.
It was a nice sunny day, so I pulled the car outside for a much needed bath.
I'm sanding the top of the doors to paint them as well.
I put tape over the chrome trim so I can sand right up to the edge of the paint
without worrying about scratching it.
Here's something I might as well fix.
A huge chip in the paint that goes all the way down to the primer.
Now's a good time to fill that in before I apply the touch up color coat.
I've got some primer and a little brush.
Just the right size for a paint chip.
And a cap.
Then just apply a few coats of primer to make it level.
So when you're clear coating panels, it's best to do the entire panel when possible.
Like the hood.
Roof.
I'll be doing the entire rear bumper, front bumper as well.
I'll be doing this whole top section of the fender.
The rest of this side isn't going to be painted.
Except for, I need to paint the top of these doors.
The clear was just starting to delaminate, so I'll be blending color and then re-clearing.
But then how do I blend it back into the lower part of the body?
With this!
Spraymax Spot Blender.
I've never used this before, but I've heard a lot of good reviews about it.
So I'm excited to try it out.
What the spot blender does is make a clean transition from the new clear into the factory clear.
A lot of times you can end up with a halo or a haze where the two clears fade into each other.
So the new clear will start heavy and then fade into the factory clear.
And the blender smooths out the transition from new to old clear for a seamless transition.
I've already sanded with 800 grit.
Next I'll do 1000, then 1200, then 1500.
And finally 2000 all the way down this c-pillar to the factory clear.
Then as I'm clearing this, I'll fade it out towards the bottom.
Then spray the blender on that transition area.
Like I said, I've never used this stuff before,
but I did a lot of research and a lot of painters swear by it.
So we'll see how it works.
This can was about $20 shipped on Amazon. I'll put a link in the description.
I'll be using the blender on the a-pillars as well.
Down where they meet the rest of the door panel.
It's important to mark the area with each grit so I can tell where they start and finish
for an even transition on both sides.
And I'll be stopping before this body line.
All this trim around the windows is staying on because they're held on with brittle plastic clips.
So I'll be masking off all those with tape.
This car has a lot of trim, but the rest will be easy to mask off.
The lights and grill I'll pull when I remove the bumper.
Already popped the corner light out when I sanded.
Pulled the chrome trim so I don't have to mask that.
I already took the lip off the bumper.
Trying to avoid tape lines where I can.
But there's some things that just aren't worth
ticking apart on a car this old when plastic clips get brittle with age.
So the paper I'm using for the blend area is 800 grit, then 1000 grit,
then 1200 grit, then 1500 grit, and finally 2000 grit.
Which is fine enough to polish out with the right compound.
First I threw some tape over the chrome trim so I wouldn't scratch it with the sandpaper.
Then I sanded each area I marked off with the corresponding sandpaper from 800 to 2000 grit.
And let it dry to check for any glossy areas that I might have missed.
I've washed this car more times in the past few weeks
than it's been washed in the past decade.
I'm getting it all cleaned up.
I'm about ready to paint it now.
How it looks right now when it's wet is exactly how it's going to look with a fresh clear coat.
Of course I'm going to be touching up the faded areas with some fresh color.
Look at that smooth glass finish.
That's what I'm shooting for.
Hopefully it looks that good when I'm all done.
This metallic red is called Persian Red Pearl.
It really pops in the sun.
Alright, I've got the car back in the garage.
I'm going to look it over one more time to make sure it's ready to mask off.
I've got the bumpers over there.
I'll start with those.
These old Honda bumpers need a lot of masking because they're not fully painted from the factory.
So I used a variety of different thicknesses of tape.
This tape is probably the best because it's like plastic.
So it really adheres to the surface a little better than your typical paper masking tape.
Like the blue tape rolls you might find at the hardware store.
It's made by 3M Scotch and it's designed for automotive use.
It's not cheap, but it works awesome because it's easy to make it curve as it goes down.
I'll put links in the description.
The really thin 1 1⁄8 inch tape is great for the curved areas.
Then once I have the edge masked, I put on a regular piece of tape with paper over that.
The bottom of the bumper isn't even visible when the lip's installed,
but I don't want to see red overspray every time I'm under there changing the oil.
Next, I wiped the bumpers down with some wax and grease remover.
I used PPG DX 330 in a lot of my other videos,
but I'm almost out so I used some prep ball which seemed to work just as well as the PPG
and it was only about 1⁄3 of the price.
I'll put a link for the prep ball in the description.
Next, I wiped down all the surfaces on the vehicle I'll be painting as well.
Hood, roof, and fender.
Check this out. I messed up here, but now I can show you how to fix a common mistake.
That's bare plastic. I sanded it all the way through the paint and primer.
It happened in a few spots where there were high points.
And paint doesn't bond to plastic.
So I've got some adhesion promoter to fix that.
Make sure it's spraying nice first.
Alright, and just a quick spray.
That's all you need.
Here we go.
Quick spray.
And good.
Done.
It's clear, it dries fast, and it makes paint bond to plastic.
This is a great product. I'll put a link in the description.
In addition to those areas of plastic showing, I also have some body filler showing.
This white area here. The gray is the filler primer.
But I'm going to use some primer sealer over this
because sometimes color coat can appear splotchy over body filler.
Primer sealer will give consistent results under the base coat, aka color coat.
Primer sealer is a good idea over a surface like this bumper.
I'll put a link for this in the description as well.
Do a light coat here.
Light coat here.
Anywhere I see that body filler showing through.
This bumper was pretty beat up.
So I'm just hitting the repair areas quick to get a uniform surface.
Then I applied a second coat.
Next, I hosed down the floor and squeegeed out all the water
to remove any dirt or dust that could kick up when I'm painting.
I went over all the steps to convert a residential garage
into a paint booth when I sprayed the forward edge parts last year.
I'll put a link to that video in the description.
Then I masked off all the areas of the car I wasn't painting.
I already talked about the tape I'm using.
When you're painting entire vehicles, you may want to invest in some masking paper.
It comes in different sized rolls and it's a lot easier, faster, and cleaner than newspaper.
If you plan on painting more than a couple times, it's worth it.
I'll put some links in the description.
Ok, the whole car is masked off.
You saw I just ran it under the hood.
Everywhere else is taped off.
I used the 1 1⁄8 inch for the curves,
the thicker tape for the straight areas,
taped up all the seams,
don't want any overspray.
I had the fender on a stand, but hung it back on the car for paint.
Got the back covered as well.
I've got this man door propped open a little.
All the fumes and overspray will go out through that door.
There's a very slight breeze today.
It should all just blow out that way.
The temp is in the 70s.
I've got low humidity.
Should be a good day to paint.
I've been talking about all these areas on the hood
where the clear coat delaminated and came off,
which then caused the color coat to fade from the sun.
I need to apply more color here to match the rest.
And to do that, I have some custom mixed touch up aerosol cans.
I bought these online.
There it is.
Honda R65P Persian Red Pearl.
I ordered these two first.
Then I decided I better order one more just in case I needed it,
as my repair areas kept growing as I fixed up the bumpers too.
They were about $30 each from eBay.
Had I known I was going to end up needing this much,
I would have just bought a quart and sprayed it with the gun.
One more thing I need to do is wipe this down to remove any dust or dirt
that landed on it since I cleaned it with the wax and grease remover.
And for that, I have a tack cloth.
This is just a thin cloth and it's kind of sticky on both sides.
I like to just unfold it all the way like a napkin.
Ball it up and wipe everything down.
You don't need to press hard, just real light pressure.
Here's the first touch up can for the color.
I just popped the cap and there's some paint dried on the tip of the nozzle.
Not sure why that happened.
Must have leaked a little.
But I can scrape that off.
Should be good now.
Give it a test spray.
And…
Ok, this isn't going well.
It's just gushing out from the base of the nozzle.
Oh man, and it just shot the tip off.
Best blooper ever!
Clearly that nozzle was clogged with paint
and the other two cans looked the exact same way.
I'm going to let them soak in some paint thinner for a while.
Just some regular old thinner here that I've had forever.
Murphy's law in full effect today.
For lacquers and urethanes that I'm using today,
you don't want oil based thinner made with mineral spirits.
This is for thinning enamel paints,
which you might have seen me use in the wheel restoration video.
After 10 minutes of soaking and stirring in the thinner,
the nozzle works now.
Now you can see I need the most paint right here in this area
and I'm going to feather it out to blend it in.
Nozzle is still good.
I'm doing light coats.
It's going to take a few before this starts to cover.
And it's still leaking at the base.
I'm just going to wrap a towel around here.
That should catch any drips so it doesn't drip on the car.
You guys always comment.
Thanks for leaving in the bloopers
and showing how to work around them.
We've got plenty today.
There's the hood after one coat of color.
Now I'll do the A pillar.
It's important to keep shaking the can,
especially if you have a metallic color like this.
There we go.
It actually covered pretty well.
And the roof.
Then I just repeated the same on the other side.
That was close.
I almost had a big drip on the painting surface,
which there's really no simple or easy way to fix that.
So this defective aerosol can is really making me nervous as I'm painting.
In hindsight, I should have just bought a quart
and applied it with a spray gun
instead of trying to blend with these aerosol cans.
It wouldn't have cost much more
and it would have been a lot less of a headache.
Just follow the contour of the bumper for an even coat.
And this is dripping all over the floor.
Looks like somebody got stabbed in here.
It's been about 10 minutes.
Time to lay down the second coat.
Seems good.
Ah, it's leaking again.
I think I'm flinging off more paint than I'm spraying.
It's starting to cover a little bit.
Look at that.
It's starting to look like a zombie apocalypse in here.
Then I came back for the third coat.
Using one of the paint my ride cans and it didn't leak at all.
And then the fourth coat.
I feathered each coat out a little farther than the previous coat
to blend in the new paint with the old.
The repair area was still a little white,
so I did another coat on it.
It's looking good,
but some of the primer was still showing.
The bumper is looking pretty good.
I can still see a little splotchiness in the bright light
from the repair areas.
I didn't bother painting the very bottom here,
because you're not going to see it.
I'm running low on paint.
I bet half that first can leaked out as I was trying to spray it.
All the faded areas up here,
they are now looking good.
I'm happy with this.
This all blended in nice here.
I could use a little more paint on the hood.
I can barely see the repair area in the right light.
It's a little splotchy.
Never mind the glossy vs dull areas,
that will all be glossy later after the clear coat.
Here's what's left of the third can.
Every bit counts.
I'm just doing an overall light coat here to blend everything together.
Also, with metallic colors, it can prevent tiger striping.
The can's spitting.
I'm about done.
Put the last little bit on here.
I wish I had about another half can.
I did not account for the one leaking all over.
Lesson learned.
Well, it is what it is for a $350 car.
On to the clear coat.
I'm going to keep this short and speed through this part.
I mentioned the how to spray automotive paint in your garage video earlier in this video.
I highly recommend you check it out.
I explain everything I'm doing here,
including the mixing ratios for the color and the clear coat,
as well as how to set up and properly adjust the spray gun.
I'll have a link for you in the description.
One last check and we're good to go.
Hey, real quick, I am not a professional painter.
I'm just an average Joe working out of his garage with some old spray equipment.
If you're looking for how to paint a show car,
you might want to find someone with top of the line equipment in a downdraft paint booth.
If you're a regular guy looking for a budget paint job out of a residential garage,
then I can show you a thing or two.
If you are a pro and you're watching this video and see something very wrong,
please let me know because a lot of what I've learned
came from working with a professional painter and I'm always looking to improve my skills.
Notice I'm holding the hose with my other hand so it doesn't drag on the car.
The first coat is just a mist coat.
No need to go heavy on the clear until the very last coat.
I'm doing the passenger side first since I can't reach all the way across.
Starting in the middle and working my way toward the edge.
Now the driver's side.
I adjusted the pressure there.
It was a little low after I started spraying.
Just back and forth.
Following the contour of the car.
Getting that edge on the back of the hood where it meets the cowl.
And you can see each pass overlaps the previous pass by about half way.
And same for the bumpers.
Spray from all different angles to reach all the different contours.
In these smaller tight areas, I move the gun faster
to prevent too much paint from spraying on the surface.
Because that will cause runs or sags.
I used more than half of the first batch of clear, so I'm mixing some more here.
Just mix clear and hardener ratios according to the instructions.
I cover that in the full video I mentioned earlier.
Time for clear coat number two.
There's a bug on the surface.
Got it.
The downside of not doing this in a paint booth.
Get the edge of the hood.
Just like last time.
You might notice the surface is starting to look a little rough.
That's called orange peel and I think the temperature was a little on the warm side.
So the clear is starting to dry before it has a chance to self level on the surface.
It's not what you want, but it can be corrected through wet sanding and polishing.
That just requires extra time and elbow grease.
I didn't have orange peel and the how to paint in your garage video,
so now I can show how to take care of that.
That's it for the second coat of clear.
Here's how it's going so far.
I got some pretty rough orange peel.
I'm hoping a heavy wet coat will level some of that out.
I think either way I'll be wet sanding.
Now on the C pillar here, I'm going to be fading the new clear out
and then hitting that with the spot blender by Spraymax.
And I'm going to do that on the last coat.
Bumpers look better, not as much orange peel.
They'll benefit from a nice wet coat as well.
Coat 3, the wet coat.
Notice how slow I'm moving the gun.
I'm laying the clear down heavy.
There's nothing to worry about on the horizontal surfaces like the roof or hood.
It's the vertical surfaces that you have to be careful on because,
as we'll see, I did get a run on the fender.
Slow and even.
And yes, my arm was starting to get tired.
I'm doing the same in front of the sunroof.
With all the problems I had with aerosol cans,
I completely forgot to blend the A pillars on the color and clear coats.
It slipped my mind and I didn't realize I planned on using the blender there
until I was all done.
So I'll be able to show a comparison of blender vs no blender when the car is all finished.
I was going so heavy on the hood and it was starting to look better.
In addition to filling in some of the orange peel,
I know for sure that I'll have plenty of clear to wet sand
without worrying about sanding all the way through to the color coat.
Looking back at this now, I could have gone a little slower in some areas
and filled in a little more of the orange peel.
And right about now, I thought I'd see how much clear I had left.
And it wasn't enough to finish the wet coat.
I topped off the gun with clear coat and got back to that extra heavy wet coat
on the other side of the roof.
Again, with everything that was going on, I completely forgot to blend the A pillar.
To blend the C pillar, I went heavy at the top
and then faded the clear downward so it would be thinner at the bottom,
almost like a mist coat.
Then fanned the blender so that it was heavy at the bottom
and then got lighter toward the top.
And then put the wet coat on the fender.
And that's looking a lot better after a nice wet coat.
I already did the bumpers off camera and was really happy with the way those turned out.
Alright, it feels good to be done with all of this.
Let's see how it turned out.
Bumpers first, because I'm really impressed with the finish on these.
Minimal orange peel.
I'm not even going to have to wet sand these.
I love the way wet paint looks.
The rear bumper came out great as well.
Smooth and glossy.
I'm glad I refinished the bumpers.
They were kind of beat up.
Oh, look at that.
I've got to run here.
Those vertical surfaces will get you.
But I'll show how easy it is to sand those out.
These bumper pieces look good.
Oh wait, look.
There's a lot of dirt on that one.
That can be wet sanded and polished too.
Now this C pillar turned out perfect.
The new clear blended in perfect.
Spray max blender is the way to go.
Yeah, a lot of dirt on the roof.
One of my neighbors started mowing as I was doing the clear.
I wonder if that's where a lot of the dirt came from.
The orange peel isn't bad,
but I am going to have to wet sand to get rid of those imperfections.
And that slight amount of orange peel while I'm at it.
Now, here's where I had a big run.
See it there?
I went too heavy on the vertical surface and it ran right down.
So I'll be showing how to wet sand that out.
I'm definitely going to wet sand the entire hood.
In addition to some orange peel, some dirt got on it too.
These turned out great.
And then the passenger C pillar.
I was a little light toward the bottom,
but that should be fine after some wet sanding and polish.
It's still a little sticky.
Almost time to remove the tape.
I like to remove the tape before the paint is dry,
so it's still soft and separates easier where it meets the tape.
I'm going to pull off the large section first,
then peel off the tape on the edge where it meets the paint.
Just pull away from the new paint at an angle like this.
Nice and slow.
Then I'm pulling off this masking tape from the chrome trim.
Check out this vintage masking paper machine I picked up for dirt cheap.
It holds a roll of tape and applies it to the edge as you pull out the paper.
Then just rip it across this sharp edge to cut it.
This is a huge time saver.
I'll put a link to these in the description.
I'm glad I put some tape on the rubber weatherstripping behind the doors.
As you can see, a lot of paint can get through.
Hey, we're back!
It's been almost a week since I painted the Legend.
The paint has been curing.
Let's see the final result.
The bumpers turned out great.
You can see there's not too much orange peel.
I'm happy with those.
On the car, the A pillars and the doors turned out great.
Then there's the roof.
Check out that orange peel.
Some areas are worse than others, like the very edge here.
But I'm definitely going to wet sand the whole roof to get it glass smooth.
The C pillar looks good.
A little light toward the bottom, but that's easy to wet sand and polish.
Back to the A pillar.
Yeah, look at that, line where the new paint meets the old.
I totally gooped, like an idiot.
I forgot to blend it in by feathering the new paint out and using the blender.
Hopefully I can wet sand that edge down and make it look decent.
I was having so many problems with the color coat dripping everywhere
as I was trying to paint.
It's a miracle that's the only thing I screwed up.
This, right here, I don't know if I just got a defective can,
but Color My Auto is now junk in my book.
Never again.
This Paint My Ride brand though, it worked great.
I would gladly purchase these again.
The hood is orange peel city.
Get close here and you can see all the texture.
It looked more smooth when it was still wet.
You can see there's some dirt in there too.
In the right light there's a hint of splotchiness in the red too.
I just didn't have quite enough to cover 100%.
When you have a thick, heavy coat of clear,
the top surface will dry faster and actually shrink a tiny bit and wrinkle up.
And warm temps will actually make it dry even faster.
And that's the same thing that happened in the how to paint in your garage video,
except it was even hotter that day.
So I'll be showing how to correct all that with wet sanding and polishing.
These things happen in real life when you're not a pro
spraying in a temperature controlled downdraft paint booth.
I'm not upset with these results because now I can share how to fix these common issues.
Like this.
I had a huge run down this vertical surface here
and it all collected on top of this fender flare.
Easy fix though.
This is all about the same as the other side.
This C pillar turned out beautiful.
I'm really happy with that.
Before this video gets too long, I'm going to call it a day
and I'll show how to wet sand to remove the imperfections and the orange peel
and then cut and polish with a buffer to get this whole car looking good again.
Let me know if you have any questions.
Please give this video a thumbs up if you found it helpful
and consider subscribing for more how-to videos and project vehicle updates
here at the 6th Gear Garage.
Thanks for watching!
