How to Repair and Remove Dents from your Car (DIY)

Auto Retech
2 followers
Hey guys, ChrisFix here, and today I'm going to show you how to remove dents from your car.
Now, I have no clue what the previous owner did to get all these dents,
but that's okay because it gives me the opportunity to show you guys how to remove dents
and make this perfectly smooth so you would never even know there are any dents here in the first place.
Now, there are two main methods to remove dents from your car.
First is a paintless dent removal kit like this, and if you have shallow, non-sharp dents,
this kit can help remove those or make them less visible without having to spray paint your car.
So what you do is add some hot glue to the puller tab from the kit and place that in the dent.
Then you take the slide hammer attachment and pull the dent outwards.
This is not as easy as it looks, and it takes a lot of practice.
And then if you pull this dent out too far, like I just did,
you're able to lightly tap the dent back in with a plastic coated hammer
and try to make that dent even with the rest of the body panel.
Again, it's not easy to do, and it doesn't work on every dent,
but with practice, you could get decent results.
Now, unfortunately, paintless dent removal won't work for these dents
because we have some deep dents that are pretty sharp,
so that metal is really bent, and it'll be hard to massage that so it's flat again.
Also, you can see all these dents have damage to the paintwork in them.
So even if we did get the dents out, we'd still have all this damage here,
so we'd have to paint the car anyway.
So since we can't use paintless dent removal to remove these dents,
the other common method to remove dents is to use a pro-grade body filler.
And with this, there are three simple steps to remove these dents.
First, you prep the dents by sanding them down to bare metal,
then you fill the dents with the pro-grade body filler,
and finally, you sand it down so it's smooth and even with the rest of the panel.
Now, that leaves you with a smooth but unfinished surface,
so you'd have to either take it to a paint guy,
or you could paint it yourself at home, and that's exactly what we're going to do.
I'm going to show you how to paint it and make it look absolutely amazing.
So let's get started.
And now here's everything you're going to need to repair the dents in your car.
As usual, I like to use common hand tools and easy-to-find products that give you great results,
so you can get this job done at home yourself, no problem at all.
So first, we're going to need our pro-grade body filler and pro-grade glazing putty.
These are professional-grade products,
so they're going to give you amazing results if you use them properly,
and I'm going to teach you how to use them properly.
Then we need some sandpaper, all the way from 80 grit up to 5,000 grit.
Then we have our spreaders, we have our sanding block,
tack cloth, we have our tape, and isopropyl alcohol.
Now, I did say we are going to spray paint at home,
and I wasn't kidding.
We're using spray cans, but we're going to get amazing results.
I can't wait to show you.
So we need our primer, our base coat, which is our color coat,
and this is color-coated to our car.
I'll show you how to find that on your car.
And then we have our automotive 2K clear coat.
After this dries, we're going to wet sand and then compound and polish
to get that amazing glossy finish that looks like the rest of the car.
Now, safety is very important,
so make sure you're wearing at least an N95 dust mask when you're sanding,
and make sure you get your safety glasses on.
And then when you're spray painting,
it's very important to use a full-face respirator with organic filters,
so you're not breathing any of that spray paint in.
And I do want to thank Evercoat very much for supporting this video
and sending me out their body filler and their glazing putty.
That way, I could teach you guys how to properly fix dents in your vehicle.
Now, enough talk. Let's go grab our dust mask,
and let's get started with step number one,
preparing the dents so we could add our filler.
Now, since we have a bunch of dents right here,
and we have a nice-sized dent back there,
we're going to end up spray painting this entire door panel.
So if you have any plastic trim like this piece right here,
you want to remove it.
So use a plastic trim removal tool and pry the trim out,
being careful not to damage the door.
And as you remove this trim,
you might break the plastic clips that hold it in, but don't worry.
They're inexpensive and easy to replace.
And it's that easy to remove door trim like this.
Now, I did break a couple of these plastic clips.
It's bound to happen. They're old, they're brittle.
And the new ones will make the trim fit even tighter to the door
than the old factory worn-out ones.
All right, so with our trim removed,
now we're going to go and sand down all these dents to bare metal.
It's important we get down to bare metal
because our body filler adheres best to bare metal.
So we're going to sand this down.
But before we do that,
it's very important that we clean the surface
because there's oils and dirt and stuff on this paint surface
and we don't want to rub that into our metal.
So grab a degreaser like soapy water
and spray down the entire panel so we could clean it off.
Soapy water is just a teaspoon of dish soap and the rest water.
And it works great at removing dirt and it also removes waxes and oils.
That way we won't push them into the dents we're working on.
So with our panel nice and clean,
now we want to use 80 grit sandpaper
and sand down all these dents and get them to bare metal.
Now we want to keep our sanding localized to our dents.
We don't want to sand out this whole area
because that just creates a lot more work.
So to help you visualize where the dents are
and how far out we're sanding from those dents,
I'm going to circle each of them.
And I can see there's a little bit of waviness in this paint up here
that I want to try to sand smooth.
So I'm going to circle this area as well.
Now these circles are here for guides.
I'm not saying you can't sand outside the circle.
It's going to happen.
Just try not to focus outside the circle.
Focus inside the circle.
And now we have one last dent on this door panel
right under the handle here.
Now I know you guys know what a dent is,
but it's not as simple as it might seem.
So obviously the dent is that deep indentation right there.
But the metal around it is also indented.
It's not flush against the rest of the body.
If I take one of these striped dent boards
and you take a look at the reflection,
you'll get a true sense of how wide the dent actually is.
So I'm going to mark the outside edge of this dent
just to show you guys,
even though the dent looks small and tight,
the metal around it is also bent inward.
So it's much bigger than you think.
So inside that circle,
we definitely need to get it to bare metal
so our filler could stick.
But also around it,
about an inch or two around it,
we want to have to bare metal
so the filler could stick there too.
And when we sand it,
we could get it even with the rest of the body panel.
And real quick,
I'm also going to circle this dent just like the others.
So now that we know where the entire dent is
and we have our area circled,
so we stay within that area,
now we're ready to sand it down with our 80 grit sandpaper.
Now when using your sandpaper,
you don't want to just use your fingers like this
because that'll create hot spots where your fingers are.
That's where most of the sanding will be.
So what I like to do is I like to grab a kitchen sponge
and wrap my sandpaper around the kitchen sponge
so now this has some give to it.
It distributes that force over the sandpaper a little bit better
and you won't get any hot spots when you sand.
So now we want to focus on this area
and then work our way out and sand this whole thing.
So with your dust mask on,
sand the dent to bare metal.
And the first time you do this,
it's definitely going to be weird to sand the paint on your car.
But you're going to have to trust the process
and not worry about it.
Now if you notice that the sandpaper is getting all gummed up,
just flick it a couple times
and you can see the dust comes right off.
Removing this dust is going to unclog that sandpaper
so it works better and makes it easier for you.
So finish sanding the dent down to bare metal
and this shiny metal right here is bare metal.
But you can still see we have paint inside the dent
that we need to get out.
So now you can use your finger and create a hot spot
and sand deep into that dent to get all the paint out.
It's very important you get this dent down to bare metal
because body filler bonds best to bare metal.
Beautiful!
Now after you're done sanding,
this is exactly what it should look like.
You can see inside our dent,
there is no paint at all.
It is down to bare metal
and then about an inch or so outside of our dent,
we have bare metal as well.
Now we also sand it into the surrounding paintwork.
Not a lot, but a little bit
so that we could feather that sanding out
and you could see the different layers of paint.
You could see the primer they put down from the factory,
the base coat, which is the color coat,
and our clear coat.
You want to have a nice smooth transition.
If you close your eyes,
you can't even feel that there's anything there.
You don't want anything that you could grab your fingernail on.
And that's nice and smooth
and that's exactly what you want.
So that's one dent done.
Now let's go get the other dent sanded down.
Now with the other dents,
you want to follow the same exact process,
making sure you sand each one down to bare metal
and remove all the paint in the deep part of the dent.
The 80 grit sandpaper works pretty quickly,
but if you have an electric sander,
definitely consider using it
because it'll make this process so much quicker.
But as usual, I want to show you guys
you could get this done by hand,
no problem.
Alright, so all our dents are sanded down to bare metal
and there's no more paint in them.
Also, this spot right up here is sanded
so that it's smooth
because we had a little wave in the paint.
So we might as well make it perfect
while we're sanding everything down.
Now we can finish up the first step
by getting some isopropyl alcohol on a rag
and wipe down the whole panel
to remove all the dust that we just created.
Alright, so with all the dents sanded down to bare metal
and I cleaned it off with alcohol,
I also did the same thing to the rear dents as well.
All of these have been cleaned up.
Now we need to let that alcohol flash off.
It needs to evaporate for about 10, 15 minutes.
And in the meantime,
let me show you how to mix your body filler.
Now we're using Evercoat Body Shop Pro Grade Body Filler
and this stuff is super easy to work with.
So under the cap, you can see here we have our hardener
which we have to mix in with our filler.
I'll show you how to do that in a second.
But my favorite thing about this entire kit
is this sheet right here.
This makes your life so much easier.
Every can of filler comes with the sheet
and it makes it impossible to mess up
mixing your filler and your hardener.
Check this out.
So first, what I suggest you do is grab some tape
and tape down your sheet to a piece of cardboard
or some flat surface.
That way it's easier to mix on.
Next, we need to pop the lid open
with a flathead screwdriver
and I always like to mix the filler
to make sure it has a uniform consistency throughout.
And don't worry,
this easily wipes right off a metal with a towel.
Now after we mix up the filler,
what we're going to do is figure out
how much filler we're going to need.
So this two-inch circle,
this four-inch circle,
or this six-inch circle.
And I prefer to start with the smaller amounts
just because you can always add more filler later.
But if you fill this up
and you don't use all that filler,
it's just a waste.
So what we're going to do
is we're going to use this four-inch circle
and this should be enough
to do all the dents on both doors.
So pour out the filler,
that way it fills the circle.
Just like that.
Good.
So after you fill that four-inch circle,
the next thing you're going to do
is grab your cream hardener
and you want to knead the hardener.
Sometimes this stuff sits on the shelf for a little bit
and it might separate a little.
And just to make sure it's consistent
and we get good results,
mix up that hardener.
Now you just squeeze out a bead of hardener
to cover this four-inch line like that.
And that's perfect.
And now you can see why I really like this sheet.
It's such a great idea.
It guarantees that you get the correct amount of filler
and hardener.
So that ratio is accurate,
that way this hardens properly
and we get a great result.
Now you want to grab your spreader
and we're going to mix these two together.
Now it's important that you don't stir with the spreader.
You want to make sure that you're folding.
If you stir, you're going to introduce air bubbles
and then when you go add this to the car,
it's going to create pinholes from those air bubbles
and that's going to give you a bad result.
So the technique is to fold the hardener
into the filler
and let me show you how to fold.
All you do is scoop up the mixture like this
and then spread it out.
Scoop it up
and then spread it out.
And then you want to repeat this process
until you can no longer see any blue hardener in that filler.
It has to all get mixed in and be one color.
And as you spread it out,
you can actually see the air trapped in the filler
come right out, which is good.
So this should take you a maximum of 30 seconds
to get this fully mixed like this.
So that's perfect.
We don't have any more blue in our filler.
It is completely mixed in
and we also spread it out nice and thin
so that it doesn't heat up.
Right now, this is undergoing an exothermic reaction,
so it's heating up
and the hotter it gets,
the quicker it hardens.
If it's 70 degrees Fahrenheit out,
we have about five minutes of work time
before this hardens,
so not a ton of time.
So with that said,
let's take this and fill our dents.
All right.
So what we want to do first
is start with a small amount of filler on our spreader
and wet the bare metal surface.
So get your spreader
and really press hard
and force that filler into the dent
and surrounding bare metal.
The filler has resin in it
and we want that resin to wet the bare metal
and that's going to help provide better adhesion
for the layers of filler we put on top of it.
And then after you wet the surface like that,
now we can add our first layer
and push it deep into the dent,
forcing any air out
and also keep the layer thin.
That way we don't get any air bubbles,
which leads to pinholes.
Now it looks like we just need one more thin layer
to build this up slightly higher
than the surrounding panel.
Perfect.
So this is a great example.
We did a good job at keeping the filler
within the sanded area.
It's not all over the place.
It's not down here outside on the paint,
because if it is,
it's going to take a lot of work
to sand that all down.
So by keeping it within here,
we're doing a lot less work
when we have to sand it down.
We also didn't put globs of filler on here.
There isn't a mountain of filler.
It's just a little bit higher
than the surrounding bodywork.
Again, that's going to make it easier to sand down
and get smooth and even with the bodywork
once this dries.
And this will be dry and sandable in 15 minutes,
so let's quickly get the other dents done.
So wet the bare metal down
by pushing a thin layer of filler
onto the dent really hard,
then build up the layers of filler
so it's higher than the surrounding panel.
Same thing for the other dents.
Wet the surface like so,
and then add more filler and smooth it out
so it's slightly higher than the surrounding panel.
And on that wavy spot up here,
I'm just going to put a thin coat of filler
since it really isn't a dent.
Okay, so not bad.
All the dents are completely filled.
We do have a little bit of a low spot right here.
Probably could have added a little more filler
to get that higher,
but not a big deal
because after we sand this down,
we're going to add our glazing putty,
and our glazing putty is designed
to fill low spots and pinholes.
So that came out perfect.
Our spot right here under the handle came out perfect.
And off camera, I did the rear door panel
and all those dents are completely filled.
Now, just to give you an idea,
here is how much filler we have left.
There's plenty of filler left
and we use that four-inch circle
and I did the entire front door
and all the dents on the rear door.
So hopefully that gives you an idea for your project
how much filler you're going to need.
You really don't need that much.
So now what we need to do
is let this sit for about 15 minutes.
That way it cures and dries
and then we could go and sand it down.
Now, as we let that dry,
I have a quick tip on how to keep your spreaders
nice and clean
because it's hard to clean these spreaders off
once that filler gets on there.
And the trick is to just leave
a bunch of filler on your spreader.
Don't clean it off.
Make sure you have a bunch clumped on there like that.
And then after your filler hardens,
check this out.
Grab your spreader
and just crack your spreader like this
and you can see the filler comes right off
in one big piece,
leaving behind an undamaged,
nice and clean spreader.
Alright, so it's been about 15 minutes,
so grab your 80 grit sandpaper
and we are ready to sand down all the body filler
to make it flush with our panel.
Now, when sanding your filler,
it's very important that you use a sanding block like this
because it's completely flat and it's solid.
That's going to give you the best smooth surface
that's level with the rest of the body panel.
If you sand it by hand,
you have these pressure points on your fingers
and that could create little waves
or indents into the filler.
And as you're sanding,
a little helpful tip that works really well
is to sand in an X pattern.
That way you're sanding down the filler
in different directions
which will give you a flatter, more even result.
So that's what your dent should look like
after the 80 grit sanding.
Now we want to move up to the 180 grit sandpaper.
And with the 180 grit,
you want to sand down the dent
but you also want to start feathering it out.
So you want to sand about 6 to 12 inches
outside that dent
into the surrounding paintwork like this.
All right, now that is absolutely perfect.
If you close your eyes
and you run your hand across this,
you cannot feel in any direction
that there is a dent.
It just feels like one smooth body panel
and that's exactly what you want.
Now with that 180 grit,
you saw me sanding out here as well.
We feathered out the sanding.
So we went from this tight area
and moved outwards
to remove all those 80 grit scratches we introduced.
So we have a smooth transition
across this whole panel.
Don't worry, we're painting the whole thing.
So you just want to make sure
that you get rid of those 80 grit scratches
with that 180 grit sandpaper.
So this is absolutely perfect.
That's exactly what you want.
Now let's repeat the process right here.
So sand down the filler with 80 grit in an X pattern
to level it out with the surrounding panel.
Then switch to 180 grit
and again, feather out that sanding
into the surrounding paintwork
to remove all those 80 grit scratches
and smooth out that paint.
And finally, wipe the panel down with alcohol
to remove any leftover dust.
Okay, so after the 180 grit sandpaper,
you can see we feathered out that sanding pretty good now.
We have sandpaper scratches all the way out here,
which makes a nice smooth transition.
Now this dent here feels great.
I cannot feel it.
This dent, there is a low spot.
This dent, just like we thought,
there's a low spot.
Same here, low spot on this dent.
And this took no body filler.
This is actually completely smooth.
So I guess the little waves
were from the factory paint job,
but we smoothed that out
so we won't have an issue there.
So with this completely sanded with 180 grit,
we know where there's spots that we need to fill.
Now let me show you how to mix the glazing putty
to get rid of these low spots and the pinholes.
Now our glazing putty gets mixed
the same exact way we just mixed our body filler.
Just make sure you get a new mixing sheet.
This mixing sheet has all these little pieces
of body filler on it.
And if that gets in our glazing putty,
it's going to ruin the putty and ruin our finish.
So out with the old and in with the new.
Now what happens if you don't have a new mixing sheet?
Well, you either need a two, four,
or six inch diameter circle
and either a two, four, or six inch line for our hardener.
Now, funny enough, our spreader is four inches long.
So you can make a circle with your spreader
or the back part of this cap for our filler
is about four inches.
So what you could do is get a piece of cardboard
and trace a four inch circle for your filler like that
and then draw a four inch line for your hardener.
But you never want to mix your filler
or your putty on here
because your hardener will soak into a cardboard surface
and then you won't have the correct ratio.
So a little trick is to grab a plastic Ziploc bag like this
and cover your cardboard with plastic.
The plastic won't absorb any of the hardener
and it's a nice flat mixing surface.
Now we could go and mix our glazing putty.
And what I like to do is I like to knead the glazing putty
just like before where we kneaded the hardener
to make sure it's all mixed up and there's no separation
and then pour out the putty to fill the four inch circle.
And then once you have that circle filled,
next let's lay down our four inch bead of hardener.
Good.
And finally, we could fold our hardener into the putty.
Just like before, spend no more than 30 seconds
getting this completely mixed.
Perfect.
So we don't have any more blue streaks
and our putty is all mixed up.
We spread it out that way it stays cool.
We have about five minutes of work time until this hardens.
So let's go fill the low spots and the pinholes.
Okay, so when adding your first layer of glazing putty,
there should be a thin layer
and we want to force that putty into the filler
to squeeze out any air bubbles
and get a good bond to the filler and surrounding metal.
Then we could add some more putty to build it up
and get it higher than the surrounding area
and do the same thing to the other dents.
Push the putty into the filler like that
and then add another layer of putty over that.
This doesn't have to be perfect coverage
because with the putty we're just filling in low spots
and pinholes in the filler.
So just focus on building up enough putty
over all the dents that you're working on.
So with the glazing putty covering all the dents
on the front door panel off camera,
I also did the rear door panel.
Now all we have to do is let this sit for 15 minutes
so it could cure and harden
and then after that we'll go sand it down
so it's super smooth.
Okay, so 15 minutes later we could sand this down
starting with 320 grit this time
and as you sand make long strokes going past the dent
and not focusing your sanding on one specific area.
We don't want to create any flat spots.
Oh man, this feels so good.
It's nice and smooth
and you can't even tell that there was any dent here at all.
This is perfect.
Okay, so now we want to do the same thing for the other dents
using 320 grit sandpaper,
take long strokes going all the way across the putty
and we just want to get this nice and smooth.
Now this came out perfect
except for one little spot right here.
You can see there is a little nick
or a little air bubble that we got in there.
So I quickly mixed up a batch of putty
and all we want to do is fill in this little indent
and just build up one more layer.
Good, and then we could just sand this down with 320 grit.
That way we don't have any indents in our body work
when we go to paint.
And check it out,
we are done with the most difficult part,
getting our dents nice and even with the rest of the panel
and this looks absolutely perfect.
All the dents are nice and flush
and our panel is looking great.
So now what we need to do
is we need to sand it down with 320
and then 400 to get it ready for paint.
So let's start with 320 grit
and we want to sand down anywhere we're going to paint.
So in this case, sand down the entire door,
that way the paint has a good surface to grab onto.
After the 320 grit,
we want to sand down the panel with 400 grit,
which is the final sanding before paint.
So make sure you get this panel looking nice and smooth
and there's no visible deep scratches
because at this point,
if you could clearly see the scratch,
you're going to clearly see it after you paint it.
So make sure you smooth them out.
Perfect.
And with both doors evenly sanded down with 400 grit,
now we need to get rid of all this dust
and a leaf blower works great here.
So just blow all that dust away.
That way when we paint,
none of this dust gets kicked up
and lands on our paint,
which wouldn't be good.
Now let's do one last alcohol wipe
to make sure we remove all the dust from the panel
and check it out.
At this point,
all the dents are filled
and the door is perfectly smooth and ready for paint.
Although right now it doesn't look amazing,
just wait till the next step where we get paint on it
and make these dents completely disappear.
All right,
now I want to keep things realistic for you guys.
Remember,
we're using spray paint cans outdoors in my driveway.
Don't expect perfect professional results.
We're going to get as good results as possible with spray cans,
but if you want perfect results,
go to a body guy,
go to a paint shop
and have them spray paint it for you.
If you're okay with pretty good results,
I'm going to show you how to do that right now.
So first,
we're going to be using an automotive primer
and we want to cover all that bare metal
and our filler,
that way it seals it off
and also it gives our next coat,
our base coat,
a good layer to adhere to.
So our base coat is literally the color of our car.
This is 354 Titan silver.
This is the metallic silver BMW uses.
So it's a paint color match
and I'm going to show you right now
how to get the paint code for your car
so you can get the exact color.
So to find the color code in your car,
usually on the driver's side,
there are door jam stickers like these right here
and it'll list the color code for your car.
Now on this BMW,
they make it a little bit different.
You have to go in the engine bay
and right here on the driver's side shock tower,
you can see BMW Titan silver metallic.
That is our paint code.
So that's how you find the paint code for your car
so you could color match your spray paint.
So after that base coat goes down,
finally we have our last coat,
the clear coat,
which seals everything in
and gives you that nice glossy finish.
Now the clear coat we're using is a 2K clear coat,
which is a special clear coat
that has hardener built into it.
So if you look at the lid,
we have this little red cap right here.
This cap goes on the bottom of the can here like that
and then you would snap this in
and that will release the hardener into the paint.
Then you'll shake this up
and now we have a two-part clear coat.
The benefit of a two-part clear coat
is it's much more similar to a factory clear coat
with the hardness,
with the chemical resistance
and the UV resistance.
So it's a lot more durable,
especially for a spray can.
But the downside is this is very dangerous to breathe in.
It's very important that you don't breathe in
the isocyanates in here.
So it's very important that you use
the correct full-face respirator that fits you properly
and the correct organic filters
if you use a 2K clear coat.
So with just a couple of spray cans and a respirator,
I'm going to show you how to get
the best possible results in your driveway.
So let's get started.
So now it's very important,
anything that you don't want painted,
you need to make sure that you cover up.
For example, our fender right here,
we don't want to get paint on it.
So this has to be taped up and covered.
And when you're taping off parts like this chrome trim,
it's important that you pay attention to the details.
Don't just tape it off and call it a day.
Not only do you want to make sure
these tape lines are really straight,
but you want to go the extra step.
I like to tuck the tape under the trim.
That way paint can get onto the door under the trim,
which will make this paint job come out so much better.
And taping up the car does take a long time.
So watch this neat little trick.
Okay, so we're almost ready to paint.
Now I set up this tent area
because we don't want to get anything on our paintwork
as we're painting.
It's not ideal to paint outside,
but that's what we have to work with.
And it's important that we don't get things
landing on our paint as it's drying.
Otherwise it's not going to look good.
So this tent hopefully will do the trick.
Now before we start painting,
you want to grab your tack cloth
and we're going to use this to remove any dust or pollen
that might have settled on any of the panels
that are going to get painted.
And a tack cloth is literally a tacky cloth
that leaves behind no residue.
So lightly wipe down the entire door panel
to remove anything that might have settled on it.
That way we don't spray paint over dust.
All right, so now comes the fun part, painting.
We're going to start out with our primer
and we're only going to prime any sections
that have filler and bare metal.
So anytime you paint,
always follow the instructions on the can
because every brand has different instructions.
In this case, we want to put down a light first coat
on any areas with bare metal and filler.
That way we can seal this in and prevent corrosion.
A few minutes after the first coat,
we can hit the spots again with a second coat
and we want to feather out that second coat
more into the surrounding paint to blend it in.
And then finally, let's lay down our third and final coat
to seal it all in.
Good.
Next is our base coat.
When spraying base coat with a paint can,
it's best to start spraying off the panel,
like onto our garbage bag,
and then smoothly go across the panel
at a consistent distance and speed
to lay down even coats.
We want our first coat to be pretty thin.
Don't expect it to cover the whole door in silver.
And since this is a metallic paint,
you could hear me shaking the can every so often
to get that metallic flake to stay suspended in our can.
That way it comes out evenly.
And after a few minutes, we could add our second coat.
And again, focus on moving smoothly and evenly
across the panel.
That way we can lay down another even coat.
And then a few minutes later,
we can lay down our third and final coat.
And just so you have an idea,
I use three paint cans,
and I barely have enough paint to do both doors.
So if I were you, I'd get two cans
for every panel that you're working on.
Okay, a few minutes later,
we are ready for our clear coat.
So remember, we need to take this cap off,
and let's put it on the bottom to release our hardener.
And then you just have to give it a firm hit like that.
And now the hardener is released into the can.
And then make sure you shake this for a good minute or two
to mix it all up.
And then we're ready to spray.
Just like our base coat,
we want to have smooth, consistent, even coats.
But with our clear coat,
we want this to go on just a little bit thicker
than our base coat.
This will help us get a better finish from our spray can.
Just make sure you don't put it on too thick and it runs.
And then after our first coat dries for a few minutes,
we can lay down our second coat,
and just make sure you get full coverage.
And then after that second coat dries,
let's lay down our third and final coat.
And this should be the thickest coat out of all of them.
Not too thick that it runs,
but thick enough so that you can see
it's going on to make a smooth, glossy surface.
And just like that,
we are done.
Now we just need to let this dry for a day,
and then we can wet sand, compound, and polish.
All right, and 24 hours later,
we are ready for our final step,
and that is to wet sand, compound, and then polish.
And this is a very important step.
So we're going to start out with our wet sanding.
And the reason why this is so important
is because we use spray cans.
Spray paint doesn't go on very nicely.
You got some good spots, you got some bad spots.
We need to smooth it out and make it all even.
Why don't, let me show you real quick.
So you can see this section right here.
It has a pretty good reflection.
That's straight from a spray can.
So that's not bad.
That's smooth clear coat.
And then this up here is all rough,
and this down here is all rough.
That's rough clear coat.
That's because it's from a spray can.
We're going to be able to get that rough clear coat
to look shinier than that by wet sanding.
And unfortunately, you can see right there,
that's a little bit of pollen.
As I was working,
we had these things landing all over the car.
Luckily, I had that tent up,
but some still happened to get on here.
So this is just the reality of spray painting
and working outside.
This is stuff you could expect when you're doing it.
If you don't want pollen like that,
take it to a paint guy,
and he'll be able to do it perfect.
But we'll still get this to buff out really nice
and look great.
So let me show you how.
So to even out that paint work,
we're going to start wet sanding with 1000 grit
and work our way to 1500,
and then 2000, 3000,
all the way up to 5000 grit,
which is super fine.
The reason why we're going that fine
is because we're doing the next steps by hand.
Compound and polish is all going to be done
with a polishing pad by hand.
So after we wet sand,
we move on to compounding and polishing.
This is our Automagic PC1.
That's next.
That's our compound.
And then we move up to the PC2.
That's our polish.
And then finally, we finish off with the PC3.
This is a super fine polish
to give us that really glossy, deep, rich look
we all expect from paintwork.
Wanna know what?
Let me show you.
So I already did the back door to show you guys
how good this could come out.
And check it out.
This came out absolutely amazing.
So that's what you could expect from our front door.
So let me show you how to wet sand,
compound, and polish.
Okay, so grab your soapy water
and let's spray down the entire panel.
Really get it wet
so that the sandpaper is well lubricated.
And we're going to start with our 1000 grit,
so wrap it around your sponge.
And then we need to wet sand the entire panel.
When wet sanding,
make sure you sand the panel in every direction,
side to side,
and up and down.
Then once you're done sanding down the entire panel,
you want to wipe it down with a towel
to remove all that sanding residue.
And now we can move up to 1500 grit.
So again, spray down the panel with soapy water,
then sand down the entire panel,
and then wipe it down with a towel
to remove the sanding residue.
We want to repeat this process
with our 2000 grit sandpaper,
which is pretty fine.
Then our 3000 grit sandpaper,
which is really fine.
And finally, our 5000 grit sandpaper,
which is super fun.
All right.
So after we're done wet sanding,
we have a nice uniform haze
across the entire panel.
It looks almost like a matte paint job.
There's no gloss
and there's barely any reflection.
It's almost like it's,
the reflection's foggy.
And that's exactly what you want to see.
You don't see any individual scratches
at all.
And that means we're ready
for our compound and polish.
Now at this step,
if you have a DA polisher,
definitely use it.
It'll make your job so much easier
and you'll probably get better results,
more glossy results at least.
But you guys know,
we are doing this by hand.
So get your polishing pad like this.
We're going to start with the Auto Magic PC-1,
which is like a compound.
And you don't need a lot.
Just get a little bit on your polishing pad like that
and we'll start with that amount.
So you understand what we're doing.
Compound is a very fine abrasive
that's removing those wet sanding scratches
so you can't see them anymore.
So when compounding,
you want to use a medium heavy pressure
and you want to buff in tight circles
to attack the scratches on the panel
in every direction.
Work your way down the door
and make sure you overlap your circles
so you don't miss buffing the compound
into any spots on the panel.
Doing this by hand takes a lot of time
and elbow grease.
Trust me when I say,
invest in a DA polisher
and you can thank me later.
Then after you're done buffing the compound,
use a clean microfiber towel
and buff away all that compound residue
off the panel.
Oh man, I'm exhausted already.
But look, it's worth the effort.
This looks absolutely amazing.
We're not even done yet.
This is our first step of three different steps.
The compound step looks great.
It's like a semi-gloss right now.
Definitely a lot more shine
than with the 5000 grit, of course.
And it's really cutting down those scratches.
And the next step, the polishing step,
should give us a pretty good shine.
Now with the PC2,
flip your buffing pad over to the clean side
and add the polish to that side.
Then same thing here.
Buff the entire door with a medium heavy pressure
using tight circles.
And I think you get the idea.
It just takes a lot of time and elbow grease.
And finally, for our last step,
add the PC3 to a new buffing pad
and use medium pressure
and buff in tight circles.
Now when you're done with this,
if you don't have the shine you want,
you might have to start over with the PC1
and then use PC2 and PC3 again
to cut into that clear coat even more
and remove even more scratches.
But this is coming out pretty good.
Okay, after our super fine final polish,
check out this finish.
This came out amazing,
especially for doing this in your driveway.
Is it perfect? No.
But this is way better than what we started with.
We had dents, we had key marks,
we had scratches all over this panel
and now it looks amazing.
I mean, take a look at that shine.
That's not too shabby for a hand compound and polish.
And I'm totally happy with that.
Now we can't forget to add our plastic trim
and I got new trim to complete the look.
And then all you have to do
is tap the trim into the door like that.
And that looks awesome.
But do I have a surprise for you.
And that's why I wanted to get the dents removed.
And check it out.
What do you guys think of the new livery?
I think it came out awesome.
Soapy water racers.
We have a race coming up,
so I had to get the car wrapped.
You're supposed to wait about two weeks
before you wrap over paint that you just put down.
But again, race is coming up shortly,
so I had to get it done and it looks so good.
There's no dents here,
which will make this look rough and indented
and the wrap came out perfect.
And the door panel just looks amazing.
This wrap looks so good.
So there you go.
That's everything you guys need to know
on how to properly remove dents from your car
using common hand tools.
As always, I hope this video was helpful.
If it was, remember to give it a thumbs up.
And if you're not a subscriber,
definitely consider hitting that subscribe button
for more money-saving DIY videos like this.
And as always, all the tools and products
I used in this video
will be linked down in the description
so you guys could easily find them.
