Upgrading a Makita GA9040S grinder with a LASERCHASER head to make a heavey duty wall chaser

Amazing Tools
4 followers
These are one of the best setups for a wall chaser.
A powerful 2400watt grinder is the perfect setup for running a 2 twin blade cutting head.
These units are perfect for chasing brick, concreat blocks and poured concreat walls.
The only option for people chasing full time.
You can buy small dedicated wall chasing machines that are good for light work. But they are not a scratch on this setup.
Plus they are one of the best priced setups also.
#machine #tools
Well folks, welcome back to the workshop. Today I've got a wee modification.
Modification to a Makita 9-inch grinder.
You want to attach a wall chasing attachment. Turn this into a laser chaser.
This is a laser chaser head. Fits on a Makita 9-inch grinder. You can also get them for a
As you'd imagine, two 9-inch discs in this here head can run off a single 9-inch grinder.
It's going to be a lot of work for this machine. That's why this takes two 7-inch discs instead.
Normally these come already assembled on the grinder as one unit.
I'm going to show where it's actually attached now.
Simply because that's the advantage of buying a laser chaser.
Wall chasers in general can get a lot of hard and heavy work.
If you're running for too hard and for too long, you can burn out a motor.
That's the advantage of these here. If you do burn out the motor on the grinder,
you can just go out and buy another grinder and attach it to the head.
If you burn it out, this is how you actually swap over the head to keep yourself up and running.
You can still fix the grinder as well, but instead of waiting for the armature to come in
or send away the port of air, it's a lot handier and faster to just go out and buy a new grinder
and attach it to the same laser chaser head.
This is how you attach them.
Now, the grinder that I'm using here is a Makita GA-9040.
This is the bigger motor 9-inch grinder from Makita.
Also do a 9020, but it's a smaller motor and a little bit too small for these here heads,
especially if you're going to have to fix a poured concrete or something like that.
It's always better to fit the bigger one just in case you're giving it extra work.
But both will actually fit.
Don't need the guards on the grinder and the handle.
Now, these bigger Makita grinders, they're actually a 2400 watt motor.
Technically, they're meant to use a 32 amp plug.
If nobody ever does fit a 32 amp plug, they always just use a 16.
So Makita and most other brands don't actually supply a plug for them.
They just let you choose whichever one you want to fit.
You can use a 16 or a 32.
Most people just fit a 16 amp plug onto these here.
So, you don't need the nut.
Inside the collet, packing flanges, locking bolts,
dust extraction port, and your head and the blades.
This couldn't be easier to fit.
Inside of here goes this here flange,
and that's what actually clamps onto the grinder head.
Two bolt holes here.
They're actually bolting on the handle holes here on the side of the grinder head.
Like I say, it either just a head.
It can either be fitted to a Makita or a Hikoki grinder.
It's this here metal flange.
These are different bore sizes.
This is the one for the Makita.
The Makita one won't fit a Hikoki, nor this deep plate here.
This will have to be changed as well.
This will either change it from a Makita to a Hikoki grinder.
Now initially, when these are brand new and never been fitted before,
this flange has to be put inside the head.
That only has to be done once.
Once this is in, it's set up for a Makita grinder.
You don't need to take this out again.
Put it on.
Couldn't be easier.
Out your locking knob here.
Just open up the whole head.
This here flange just drops on.
Socket has a bolt on the side.
It's actually clamping it onto the head there.
That drops on.
Now, all set up.
Couldn't be easier.
All you're doing is just dropping it over the top.
It's easier to tighten the bolts first before you tighten up the socket.
It gives you a chance to move things around to make sure it's all lined up correctly.
If I tighten this here first, I might not get these holes lined up correctly.
Might just make things a little bit more difficult.
Put the DEM on.
Nice and slack.
Then go ahead and tighten up the socket head.
Make sure you're putting it on square.
Clamp it down.
Then...
Then just tighten up these two bolts.
The lever here for your side handle.
Clicks into place.
Tighten that up as well.
That's your head.
Now, some blades.
Comes with three packing flanges for your blade.
It actually spits two blades out.
So you can change the gap between the two blades.
Change the size of your case.
Top on them.
It's directly locking.
Center arbor for centering everything.
Goes on through the spindle itself.
Then go ahead and fit your blades.
Set this up any which way you like.
And as always with a diamond blade,
make sure you follow the directional arrow button on the blade.
These are directional.
They have to spin the correct way.
Follow this arrow.
Tell you which way to put it on.
Find another arrow on the laser chaser head.
Match them up.
And your packing pieces.
And your second blade.
Instead of using the top nut then on the grinder,
I'm going to get rid of that.
And just use this here top piece.
It just has a bolt on top.
Hold it all together.
And your side handle.
Just screws onto the handle mount at the top.
That's our setup ready for work.
I've added these Makita ones as well.
Actually rotate the actual trigger handle too.
You can adjust it to sit whatever way you want to be holding it.
As well.
And storing.
Change this side handle over to the other side.
So it's not in the way.
Or if you're left-handed,
go the other way around.
Now, you're going to put a plug onto this.
So,
that's her ready to run.
Last thing,
is just your dust port.
This is to adjust the arbor size.
I've got a standard hoover.
That's her.
Ready for work.
I'm going to adjust the depth of your chase.
Just loosen off this knob.
Set your depth here in this here scale.
Just set that to 10.
You take a 10mm cutting wall.
Finally,
a rubber cap on top of that bolt.
Keep everything covered.
That's it.
That's how you fit a laser chaser,
wall chasing head
onto a Makita GA-9040S 9-inch grinder.
This is a much better setup for wall chasing.
This can be used for a longer period of time
and do much more work than a standard wall chaser.
A little bit expensive initial outlay,
but a lot cheaper in the long run.
If you have any problems with your machine,
simply unbolt it and put a new one.
Very, very good setup.
And well worth an investment
if you're doing any wall chasing.
Check them out.
Laser chasers.
