5 Uncommon Archery Hacks I Use

Kramer Ammons
208 followers
1 Video View·Oct 23, 2024
wish I would have known these five
archery hacks earlier my name is CR
Ammons thank you so much for joining me
today the first one I shared in a
YouTube short but I recognize most
people who watch these full form videos
don't watch shorts so I want to play
that short for you right now it's how to
make your archery target last three
times longer your archery target sucks
because it no longer holds arrows here's
how to double the life of a layered
archery target say goodbye to the
wrapping remove the wood split the
Target make the edges the new
middle place your target back on the
wood bring the wrap back over and onto
the Target now for the magic sauce use a
ratchet strap to retighten the
Target add a new face to your target
this is the same bow same Arrow not the
most beautiful Target but seriously if
you use a layered Target this trick
works so good just to extend the life of
the target if that's what you're looking
for second trick is how to set a perfect
knocking Point without messing it up
whether you use brass knocking points or
serving thread to tie a nail knot
sometimes it can be difficult to get it
in the exact location where your arrows
tuned because if you pinch on this brass
in a spot and then realize oh my Bow's
not perfectly tuned then you have to
remove this and do another one so this
is how I solve that problem duct tape
painters tape gap to any type of tape
let's rip it into a small strip just
like that absolutely can be done without
this but this gives you a really good
starting point I like to start my arrow
point high and then work down until it's
tuned I generally will start about 1/4
in above the center line of my arrow
rest check this out here's the magic
just put the tape on right there now you
can knock your arrow directly beneath
the tape and this allows you to shoot
the bow without committing to a knocking
point then you can slightly adjust the
tape until your arrow is tuned perfectly
once my arrow is tuned to the bow I've
got the tape on here I'll grab my
Sharpie and Mark on the serving directly
underneath the tape now I know the
Sharpie Mark is where I want to knock
the arrow remove the tape place your
knock directly above the Sharpie Point
crimp it on or tie a nail knot there
whatever method you use and you're good
to go you tuned the bow without having
to fiddle with crimping these on and off
and on and off the next one's a big
timesaver sometimes I like to Fletch my
own arrows but I hate waiting for the
glue to dry now there is fast drying
Fletching glue but I have found this to
work even better at least for me which
is an industrial CA glue mixed with an
accelerat the CA glue is medium
viscosity so it's real easy to apply but
this super glue doesn't cure immediately
it takes maybe 30 minutes but when the
accelerator is applied it cures within
10 seconds so what I do is I put the
glue on the Fletching itself then I put
the accelerator on the Arrow put the
clamp in within 10 seconds it's done and
I flip to the new Arrow I use these for
woodworking all sorts of little hobby
project have you use this super glove to
back a bow that I built this stuff is
fantastic and since I have it on hand I
tried it one time and it's held up even
better than a lot of the Fletching glue
does I'll leave a link to these in the
description of course unsponsored I just
like these things I probably shouldn't
share this next one but I'm going to
anyways do this at your own risk now I
think this is kind of a hack when you
get good at stringing a bow with using
the leg method especially when it's not
a recurve recurves are a little more
iffy I would recommend a bow Stringer in
most cases but if for some reason you do
dare to try this here's a couple
pointers one don't put the tip overlay
on the ground if you put the tip overlay
on the ground it can rip it off so I'm
just going to lay it on the right leg
then your other leg is going to be in
the middle of the handle right where the
pressure would be when you shoot it
other hand up at the very top and then
you can just press forward pull back and
it's that simple the heavier poundage
bows the harder it is but if you're
strong enough to draw the bow back you
are probably strong enough to string it
and unstring it with the leg method
warning big warning downsides you can
twist your limb especially with recurves
if you string it with the leg method
when stringing a recurve it can slide to
the side and be outside of the string
grooves which is very bad it can come
out of the string Groove snap back on
you and it can hurt this is the one hack
I don't recommend but with long bows and
recurves I like to do it the only reason
I really do this is purely for speed for
example in this video I've already
strung up four or five different bows
just for b-roll and to pull out a bow
Stringer every time would take a long
time whereas by learning that it uh it's
pretty quick I've naturally done this
method for over 10 years and I've never
damaged a bow doing it I didn't mean to
lie but see that tip
overlay this is a when 100 lb bow I
built 4 years ago and I tried to string
it with a leg method and it snapped down
and hit the concrete and the tip overlay
broke off I have damaged a bow with a
leg method but the normal poundage bows
and the normal bows I I don't uh but
don't recurves just don't do it but I
save time doing it and I do it all the
time so it's kind of a hack for me I'll
leave that up to your own decision
whether you do it or not one of the
issues with having a Flemish twist bow
string is that while you store it or you
trans your bow with the bow string off
your bow if it twist a couple twist then
when you string it on the bow your brace
Height's going to be differently what's
bad with that well if your brace Heights
differently then your knocking Point's
going to be off and your arrows aren't
going to be flying correctly so how do
you make sure after you take your string
off the bow that it doesn't untwist or
twist up or you accidentally just twist
it once to level it up but you twisted
it in the wrong direction when you put
it back on your bow how do we avoid that
I still think there are a few different
types of people when it comes to the bow
string twisting it's like the first type
of person is let's just it doesn't
matter to me let's just throw it in
there I'll shoot it my Arrow's flying
bad I'll twist it I'll I'll measure my
brace height with my bow Square I'll
figure it out out in the field it
doesn't really matter and I'll figure it
out then you've got the person who wants
to keep it precise and particular every
single time so that they know nothing's
changed and they're good to go as soon
as they put it on the bow because I
build bows and test bows I'm actually
the first person I use the same bow
string for 10 different bows and then
everything's mixed together and I rarely
ever have a specific setup that is just
dialed in all the time with the same
arrows because I test a wide variety of
gear so I'm always just tweaking my gear
to make it fit but I imagine if I got
into tournament archery in the future
I'm going to want this to not move at
all so that I'm good to go when I go
practice I don't want to waste any time
and I'd be good to go when I go to a
tournament there's not a right and wrong
but for most of us if we are able to
spend less time fiddling with the gear
and more time shooting the bow that's a
good thing a little while ago one one of
the customers who came into the shop
showed me a specific method a specific
way they tied it up that they learned at
the archery School of the Rockies that I
forget it looked very um aesthetically
pleasing and I looked online and I can't
find how this specific knot or the
specific way to tie this string is it
might be pretty standard in a lot of
places and I just don't know about it
but somebody leave a link to a video in
the description or make a video yourself
leave it in the description or an
article or something so we can figure
out how to tie it properly what I've
done is one of them goes goes under into
the middle the other one goes through
the top and holds it off like that and
that holds but it's it's ugly so that
absolutely works but if you want to do
the same thing without having to tie it
grab a plastic clamp cuz plastic will
keep it from cutting the bow string and
just put it through the string Loops
then with the rest of the string you
don't have to do anything with it
or you can wind it up and put it in the
clamp as well throw this in your bag or
you want to transport it and you're good
to go when you undo it it's on the clamp
so it didn't wind up or unwind
