"Many thanks to https://www.pcbway.com the sponsor of today's video. Check out their website to start your next project!
We replace the broken chuck on this DeWalt DCD796 combi hammer drill. Normal chucks have a set screw down inside the throat to remove the chuck but these type need to be unscrewed from the shaft while it's being held tight. I show you how to do this safely and to avoid damaging your gearbox. Should work with any drill that takes these screw-on type chucks, Makita, Milwaukee, Hitachi, Hikoki, AEG, Bosch etc. May also work with DeWalt DCD991, DCD996, DCD771, DCD796, DCD998, or any other model that doesn’t have a set screw.
This video is for entertainment purposes only and is not intended to be a guide or tutorial. Undertake any related activity at your own risk.
If you enjoyed this video and would like to support my channel, please feel free to 'like' the video, leave a comment, or if you're feeling especially generous, share the video. But you don't have to do what I tell you, I'm not your mum."
Hello, welcome to the basement. Today we're going to fix this drill. So here we have my DCD796.
Now the chuck on this has stopped tightening. It got really hot one time and some stuff sort
of fell out from the inside and now when I go to tighten it, it just spins freely and it doesn't
move the teeth anymore inside. So what we have to do today is remove the chuck and put a new one on.
Now what I'm going to show you is how to remove this because it's not very clear. A lot of drills,
they have a screw on the inside, but this drill, it doesn't have any screw in there,
it just has a pin. So it's not very clear how we actually remove this chuck. Now I have seen some
people tighten something into the teeth and then just wrench on it with the drill and a vice,
but that can damage your gearbox of the drill. So I'm going to show you a method
how we're supposed to get this off the factory way and replace it with a new one safely. Let
me just take a second to introduce the sponsor for today's video, PCBWay. They do 3D printing,
CNC machining, sheet metal fabrication, injection molding, and of course a range of different PCBs
from surface mount through hole mount, whatever you need. They have a range of projects you can
pick from from their project library or you can just have them develop your own custom PCB.
For all your PCB needs, check out PCBWay, kind sponsor of today's video. So before we get
started, you're going to need, of course, the replacement chuck and a T10 Torx driver to pull
the drill apart. And we're going to need some other tools, but I'll show you them as we get to them.
The chuck I've ordered, it is part number N196034. So if you need a chuck, that's the part number
you need to quote to whatever supply store or part store you're getting it from. So let's get
started pulling it apart. Now you have to, on this clutch ring, there's a little indent, so you need
to line it up with where these Torx screws are so that the screwdriver gets the right angle and then
doesn't get pushed too far to the side. So I'll take them out now and I'll show you what we do
next. Right, so let's take the rest of these screws out from the body. Okay, so you should
have removed nine screws from the side of the drill and, of course, we've removed four from
the gearbox housing as well. Now it won't split apart just yet because on the back of the drill
is a sticker which is going across the join and there's also one on the foot of the drill
down here which is the sticker and the light switch. So what we're going to try and do is
peel them off carefully. So I've just got a Stanley knife here and I'll try and get under that sticker
and just peel it carefully off. All right, so that sticker tore a little bit. They often do tear these
stickers. Sometimes I'm just tempted just to make a cut down the middle there. Okay, so that one peeled
a bit easier. Now the drill should come apart and there we have it. There's a fair bit of dust in here.
You can probably see that. So while you're in here it's a good idea to clean everything up.
I'll fire up the compressor and give it a blowout soon. But first of all we want to remove the
gearbox here. So we have our speed switch and that should come out with the unit. Here we go.
So we don't need this part anymore and the other housing. We can put that aside.
Now this is what we're going to be dealing with in order to remove our chuck. Okay, I've got an
old rag. It's a bit greasy and oily in here. You're going to need to get a Phillips head number two
driver and we're now going to take the screws holding the gearbox to the clutch mechanism.
And that's six screws that hold the gearbox in. We'll try and keep these
in the one spot. And our goal is to lift this entire gearbox assembly out in one unit.
All right, not too bad. We managed to get it out mostly in one piece. Right, so what you should be
left with is the chuck spinning on a shaft. So you can see the shaft there. Now that's what we
want to clamp onto while we reef on the chuck to unscrew it off the shaft. So it's screwed on there
really tightly and that's the reason why a lot of people just rely on the reduction of the gearbox
to provide enough torque to unscrew it. But that can really damage your gearbox. You really have
to reef on it really hard. So what we'll do is set up something in the vise to clamp onto the shaft
and then we will unscrew it. So just before we chuck it in the vise, all of these pins and things
are just sitting in there with gravity. So I've just knocked them out. We can put them back in
again at the end, otherwise they'll fall out while we have this upside down in the vise. Okay, so if
you talk to DeWalt when you're getting your chuck, they'll advise you that you need a special tool
to be able to change it around. You don't actually need that, you just need a decent sized shifting
spanner. And what we're going to do is hold the shifting spanner in the vise and the shifting
spanner will hold the shaft of the drill. So the reason they advise you need a special tool is you
can't just stick that in the vise because the shroud of this gearbox housing thing is in the way
of getting into the vise. So all we need to do is hold it with this, tighten that up. Okay, now the
chuck's in the vise and that shaft's being held securely, we want to be able to unscrew this chuck
here. So what I do is I use a great big Torx bit here, it's a Torx T55, and I tighten the teeth
around these nice big chunky faces here and then use my breaker bar just to pop that chuck off.
So I'll do that now. Now remembering my chuck is, there's something wrong with the side, so it doesn't get
very tight, but I can hopefully tighten it enough that I can unscrew this chuck. So that's as tight
as it will go, it just spins from there. So now what we'll do is we'll throw our breaker bar on
and this needs quite a bit of pressure, so let's break it off. Right, so there we go,
unscrewing the chuck. It's a bit nerve-wracking the first time you do it, it feels like you've
broken something, but it just needs that much torque to get it off. So there we have the old
one, that there's something broken, and the new one. They do look slightly different, but hopefully
the thread's the same, they should just fit on. So what we're going to do is the reverse, we'll
tighten it around our Torx T55, and just tighten it as tight as we can get it. Okay, I'm happy with
that. Done. Okay, so before we put the clutch back in, these pins here, just make sure they all go
back in. There's six of them, and they have a round edge and a flat edge. Put the flat edge down
and the round edge facing up, and there's one with a little spring on it here, and that faces down,
and that provides the detent for the clutch ring. Okay, that took a bit of doing, but if you're just
methodical and careful, you can get it back together. It is probably the hardest part of
this whole operation, I was getting that gearbox back into this housing, but we're all good to go.
I'm going to put this back into the two halves of the drill, and we'll fire it up and test it works.
So, all fixed, everything's working. Chuck goes in, chuck goes out, chuck tightens, which is the main
thing it wasn't doing before. Now, I don't know why Dewalt used this type of chuck where you can't
just use an allen key to undo it from the inside, why you have to dismantle the whole thing, hold
onto that shaft, and then use a lot of torque to unwind it off the thread, but they do for
whatever reason, and this is the only way that I know to do this safely without damaging your gearbox.
So the hardest thing about this operation was actually getting that gearbox back together, so
if you need to do this, just take that into consideration. Just take your time, be very careful,
and make sure everything goes back aligned and in the right spot. You'll know if it doesn't because
it won't work. So this particular fix works on this drill, the DCD796, but also the 791 and the 790.
So if you've got one of those drills and you're working out how do I swap out and change the chuck,
that's how you do it. Thanks for watching, you've been in the basement, have a great day.