DIY Nightstand With Fluted Design

Handicraft
4 followers
1 Video ViewยทSep 11, 2024
Hey I'm Zach welcome back to Bear Mountain Builds and today we're going to be building
some fluted bedside tables. We're kicking off this project by stripping down my three quarter inch
sand plywood into more manageable sizes. I'm building the carcass with miter joints so I'm
setting my table saw blade to 45 degrees then cutting the sides to length. With all the sides
of the carcass cut out I'm moving on to stripping out pieces for the base and cutting them to length.
I'm adding pocket holes to attach these stretcher pieces to the legs and the carcass.
I'm cutting the legs out of a piece of two by four. I'm cutting a quarter inch by a quarter
inch slot on the internal side of the carcass walls to hold the back panel. I'm using a piece
of quarter inch plywood to set the depth and space the slot a quarter inch from the edge.
I'm cutting the back panel out of a sheet of quarter inch plywood then trimming it to final
size. All right we've got everything cut out for these two nightstands. The whole process
goes pretty fast. We've got our legs, we've got our bases with pocket holes drilled into them,
we have our shell with a slot cut out for our back panel, and we have our back panel. Now let's put
these things together. I'm putting these miter joints together with glue and inch and a quarter
brad nails. Miter joints can get really squirrely when you're trying to put them together that's why
I made this jig. I'm using two 90 degree positioning clamps mounted on my table then slide my two
sections into place and add a third positioning square to the top. These squares are worth their
weight in gold for this project or any time you're putting together 90 degree joints.
As you can see these clamps do a great job holding everything perfectly square.
All right quick update what you saw before was these for my bases this was my whole pocket
screw setup. Now I figured out that this is way too many pocket screws for this amount of board
so I changed it to this so that way when they go together the screws are offset when they go
into those legs. Much less stress on this and it's a way better design but you'll see all that in my
plans. With the carcass put together I'm moving on to the base where I made another positioning
clamp jig to keep everything square. I'm using a piece of three quarter inch plywood as a spacer
carcass using glue and pocket screws. I'm using a couple pieces of three quarter inch plywood to
center the base on the bottom. All right we got our carcasses and bases all put together and
honestly this whole process is really easy and they're looking super good. Now we're moving on
to building out our drawers but before we do that please hit the subscribe button so you can stay
up to date on all my future projects and hit the like button too. Now let's keep going. I'm stripping
my drawer pieces out of half inch sanded plywood then cutting them to final height and length.
Just like the carcass I'm cutting a quarter inch by quarter inch slot.
To allow the drawer bottom to slide in I'm cutting all the way through on the back wall.
Remember when making this cut to use a sacrificial board to keep everything square.
I'm drilling pocket holes in the front and back drawer pieces. All right so we got all of our
drawer sections cut out slotted and pocket holes so we are ready for assembly but first we're going
to sand everything down while it's still flat then put it together. It's nice to have your cousin
around so you can put her to work. I'm using the same jig as before to put everything together.
The drawer bottom slides right in and I tack it in place with inch and a quarter brad nails.
All right we got our drawers all done they're looking super good and they are rock solid but
before we get these mounted into our carcasses we got to build some drawer fronts. Now I'm super
excited about these drawer fronts because we're going to be doing a really cool texture with some
half inch dowels but before we get to that we got to cut up some poplar. I'm stripping down poplar
for the drawer face edge then cutting it to length. I'm aligning the top of the stacked bit
with the top of my piece then setting the cutting depth to a quarter inch. I need to add a tongue
and groove to these poplar strips but they're pretty small and I value my fingertips so I cut
a jig to hold the pieces while I'm running them through the router. With the tongues cut I aligned
the single blade with the tongue itself then cut a quarter inch deep groove. With the edges done
I'm cutting out the center panels from quarter inch plywood. With everything cut out I'm gluing
super good and you know at this point you could just take these put these on your bedside table
and it's going to look sweet but we're going to take these bedside tables to the next level
so what we're doing is we're taking these half inch half dowels and we're going to cut them into
small strips to pack them in here vertically on these drawer fronts it's going to look sweet so
let's keep going. I'm cutting the half dowels to length you want these to fit snug but not to the
point where you have to force them in. This whole process takes a little finessing but I recommend
doing a dry fit first to make sure everything is fitting correctly. During my dry run I found that
I needed a third of a dowel on each end I've since modified my spacing on the plan so that they
shouldn't be needed anymore. To cut these thirds of a dowel I hot glued a full dowel strip to a small
inch back panels for spacing and support. With the fronts drying I'm moving on to installing the
sliders. I'm positioning the sliders so they'll be dead center on the drawer. Sliders can be kind
of tricky to install but with the Kreg drawer slide jig it makes it really easy. I'm using an
offcut of poplar to use as a spacer to back set the sliders so that the drawer front is even with
the front of the carcass when closed. What's great about these drawer jigs is they can now be reversed
and hold the drawer in place while you attach it to the slider. You want to make sure to flush up
the end of the drawer slide with the front of the drawer. For the bottom drawer instead of using the
drawer jig I just cut a couple spacers for the drawer to sit on. And with one last hard to reach
screw the drawers are done. All right we got our drawer fronts done they're looking super good I
am really pleased with how they turned out. We've got our dowels on here we got our back plates on
so now we're going to drill two holes for our knobs to be able to mount on here and then we
can mount these up onto our nightstands and after that we are almost done because all we have left
is paint. I'm marking the holes dead center on the sixth dowel end. I'm starting with an 11 16th inch
spade bit at 1 16th inch deep which will allow the knobs to nest into the dowels. With all the nested
holes drilled I positioned the drawer fronts in place then drilled all the way through. Now we can
finally attach the drawer fronts. All right we got both of our nightstands put together they look
amazing these are really turning out super great. Now we just need to get these things prepped and
painted. I filmed two hours of sanding so here's 10 seconds of it. All right we've got both of our
nightstands all put together and they are looking absolutely amazing. Now I was getting these prepped
and my original intention was I was going to paint these a really rich dark green almost kind
of a black but I've decided it hurts my heart too much to actually paint these. I think they look
way too good natural to paint them so we're pivoting we're going to be doing a clear coat
with poly on these things so I'm going to finish off sanding get a poly coat on there and these are
going to be ready to go. I sanded everything to 220 grit then applied two coats of crystal clear
done they look amazing I am super pleased with how these things turned out. Now there's two reasons
why I built two of these one I have two sides to my bed but two I don't have to buy any extra wood
to build a second nightstand the only thing extra I have to buy is the hardware so there really is
very little extra cost for building a second one. If you want to build these I do have plans for
these link down below in the description so if you're interested go check those out. Now if you
are going to build these I do have one thing is I use poplar to do these fronts and that was because
I was planning on painting them but poplar does have a greenish undertone so if you plan on
building these I would recommend you use aspen if you want to keep them unpainted just because the
tone will match everything a little bit better. Now as always hit the subscribe button so you can
stay up to date on all my future projects and if you enjoyed this video please hit the like button
it helps me out a ton and I really do appreciate it and also leave a comment let me know what
you're thinking about this video if there's anything you would do differently or improve
upon. I love reading all your guys comments they mean a ton to me so thanks for watching
and I'll see you next time.
