How to Build Basic Cabinets--Using ONLY PLYWOOD!

Handicraft
4 followers
Hey guys it's Shara from Woodshop Diaries and today I want to show you how I built
my shop cabinets. Actually I made a video about how to build cabinets like three years ago when
I built my kitchen cabinets. When we moved into our new house I kind of missed my old kitchen.
I thought you know I could just build a mini old kitchen in my shop. So that's what I did and I'm
going to show you how they all came together and how easy it is to just build some basic
After unpacking most of my stuff in the new shop I still had some paints, spare parts,
and just some odds and ends items so with nowhere to go. So I decided to build out this back wall
and add two tall pantry style cabinets on each side and some basic base cabinets under the window
with a space in the middle to add a little desk area. I built my previous kitchen cabinets this
exact same way so if you're looking to add cabinets to your shop your kitchen or just to make a built
in this is a simple way to go about it using only plywood. I built everything here using pure bond
three-quarter inch birch plywood except for the doors on the base cabinets that were pure bond
three-quarter inch hickory plywood panels. I'll link the details, plans, tools, and products for
this project in the description below but for now here's the breakdown of how everything came
together. I had purchased a stack of plywood for this and some other upcoming projects so the first
thing I did was start cutting everything down into more manageable pieces. I used my kreg rip
cut and circular saw to rip three sheets into 23 and three-quarter inch wide strips for the
pantry cabinets. By the way, I will link a detailed guide for how I cut down my plywood sheets in the
description below. And then I ripped three more sheets into 22 and three-quarter inch wide strips
for the base cabinets. This gave me six strips and I could use one to make each base cabinet for a
six cabinets. I kept the leftover strips to use as support pieces. You'll notice that I made the
pantry cabinets a little deeper than the base cabinets so they'll be the same depth as the
countertop running between them when I add that at the end. Then I ripped one more sheet right down
the center to give me two 24 inch wide pieces that I can use for the pantry doors later. I
labeled all of these pieces and then began assembling the pantry cabinets first. To keep
things simple, I just made the pantry cabinets a full eight foot tall so I didn't have to trim
the sides. I did however use my kreg accu-cut and circular saw to cut six 22 and three-quarter inch
long pieces from the plywood strips that I cut for the pantry cabinets earlier. I'll use three
for each pantry, one at the top, one at the bottom, and one in the middle. Now you've probably seen
people build and install cabinets and use like a two by four base to set them on instead of making
a toe kick and that's a great way of doing things, but I usually just cut the toe kick.
If you don't know what I mean when I say toe kick, it's this little recessed section underneath the
cabinets that allows your feet a place to go into I guess so you can stand closer to the cabinets.
Honestly I don't really know what the thought process was behind the invention of the toe kick
but it's on most cabinets. I'm not sure if there are quote-unquote standards for toe kick dimensions
but when you build things yourself you can kind of do what you want so I usually cut mine about
three and a half inches tall and about four inches deep. I just mark these out on the front
bottom corner of my pantry sides and cut them out with a jigsaw. Now I was making all of these
cabinets frameless so the front edges of the plywood cabinet boxes will be exposed in the end
result. So before moving on I went ahead and applied edge banding to the front edges of each
piece of the cabinet. I'll link a detailed guide on applying edge banding in the video description.
Before assembling I needed to cut two small plywood strips to use to secure the pantry
cabinet to the wall. For this I just cut these from the leftover strips of plywood from the
beginning of the video. Next I pulled out my kreg jig to drill pocket holes to assemble this cabinet.
I drilled three quarter inch pocket holes into the ends of each of the shelves and the two support
strips and then I assembled using one and a quarter inch pocket hole screws. You can use glue here as
well if you wanted. I attached the bottom panel three and a half inches from the bottom edge of
the sides, the top flush along the top edge, and the middle piece exactly in the middle of the
cabinet. I like to add a middle shelf piece in really tall cabinets like this just to help keep
the sides from bowing in the center. I installed the two support strips like shown here, one
directly below the top and one directly below the middle shelf. So this cabinet right here is going
that corner. I don't want to butt the edge of the cabinet straight up to the wall because I
will be running baseboard along the bottom. The baseboard is just a one by six so it's three
quarter inches thick and so when it butts up to this cabinet if this was directly against the
wall it would like hit the door. I've got these scrap three quarter inch pieces. I'm just going
to glue this on here so I can butt this up to the wall and then my baseboard will hit it instead of
hitting the actual cabinet. Once the first pantry cabinet was assembled, I glued a scrap spacer
strip onto the side to leave room to add my baseboards later. Then I cut a piece of quarter
inch plywood to staple onto the back here. Once the glue was dry on the spacer blocks,
I drug it over to where it was going and secured it to the wall. I used a level and a couple of
shims to set the cabinet so that it was straight and square, then used a few screws through the
support strips in the top and the middle of the cabinet to secure it to the wall studs.
I repeated this entire process for the second pantry for the other side of the cabinets.
Now before we move on to the base cabinets, I want to take a minute to share about our video
sponsor, Craig Academy. Now you guys know that I love Craig and you have and will see me using
several of their tools, jigs, and guides in this cabinet building process. But besides the fact
that they make cabinet and furniture building easier with their tools, they also provide so
many helpful resources to inspire, educate, and encourage people from every skill level to get
building. Craig recently launched a new online learning platform called Craig Academy. This
platform offers premium project plans, expert-led video courses, and over 40 skills videos breaking
down basic foundational information that you can use in every project that you build. While you're
over there, you may even see a few familiar faces in some of those videos. If you want to learn more
about Craig Academy, I will leave a link to check it out in the video description. In the meantime,
let's get back to work. I built all of my base cabinets here the exact same size. I was using
24 inch wide pieces of hickory plywood for the doors and they were full overlay doors. Now usually
when I make full overlay doors, I'd take the overall width of the cabinet and subtract a
quarter inch. So if I made my cabinets 24 and a quarter inches wide, I wouldn't have to cut my
doors any narrower. So that's what I did here. But if you need a different size cabinet than
24 and a quarter inches wide, obviously you can modify the sizing pretty easily. From each
plywood strip, I cut two pieces 34 and a half for the sides, one 22 and three quarter for the bottom,
and then I kept the little leftover strip to use as a support piece later. I did this for all six
base cabinet boxes and also cut the toe kicks in the front bottom corners just like I did on
the pantry sides earlier. In addition to the one support piece left after cutting each plywood strip,
I also cut two more for each cabinet box the same length. Two will go on the top and one at the back.
You'll see that in a minute. Once I had all of my pieces for the cabinet cut down, I drilled
pocket holes into the ends of the bottom panels and all three support strips. And just like the
pantry, I applied edge banding along the front edges of everything that will be exposed, which is
one of the support strips, the bottom panel, and the two sides. After everything was sanded well,
I began assembling these base cabinets using pocket hole screws. For these base cabinets,
I installed the bottom panel three and a half inches from the bottom edge so that it's even
with the toe kick cut out. Then I installed the edge banded support strip at the top and the front
and the two others are at the back corner. The strips at the top will be used to secure
the countertop and the one at the back will be used to screw the cabinet to the wall.
After all the boxes were together, I cut quarter inch plywood back panels to staple onto each one.
You could definitely route out a rabbet to set these into if you wanted, but you won't be seeing
the sides of any of these cabinets so I didn't really bother with it. I just stapled them in place.
I always like to check that my back panels are square and then adjust my cabinet boxes to match
when I staple them on. That way I can make sure my cabinet box is square.
Now sometimes I do things out of order and this is just one of those times.
I had both tall pantry cabinets installed to the wall and I was trying to get all the base
cabinets installed before the end of the day here, but I was waiting on drawer slides and I didn't
want to put the back on the drawer cabinets until I had the slides in. Long story short,
I just went ahead and screwed four of the base cabinets in place, two on each side,
and I just came back later to deal with the drawer cabinets. I screwed the two base cabinets together
first and then I used a level and some shims to get them level and square before securing them to
the wall studs through the back support. This concrete floor was really unlevel, but most of
them are I guess, so I just did the best that I could. I was planning to paint the two tall
cabinets gray, so while I was waiting on the drawer slides to come in, I just went ahead and cut the
doors to length and prepped them and the cabinets for paint. You guys know how much I hate painting,
so literally this is the only footage that I got of it. I primed and painted the cabinets and the
doors and I wasn't super careful because I was planning to cover the back wall later, so please
don't judge my terrible paint job. I used some Kiehl's 3 primer and just some basic latex paint.
Nothing fancy for these. One thing I love about building cabinets from pure bond hardwood ply
is that it's already smooth and since it's just raw wood, it takes paint really well and it sticks
good. I know it's easy to overthink painting cabinets, but if you just use a good primer
and a decent paint on plywood, you'll be fine. But if you want some extra tips, I do have a
detailed guide to finishing raw wood furniture that I will link in the description below.
Anyway, while the paint was drying, the drawer slides came in so I could get back to the fun stuff,
building. I used 22-inch drawer slides on the bottom two drawers and 16-inch slides on the
top drawer. I actually ordered six pair of 22-inch slides to use on all of the drawers,
but I realized later that the top drawer would hit the back support piece if I use a 22-inch
slide on it. I keep a stock of 16-inch slides in my tool chest, so I just swapped these out for
the top drawers. I don't have a fancy reason for why I used 16-inch, except that I just happened
to have some handy. So I installed these into the two drawer cabinets and added the back panel,
then I secured these in place on the wall. If you're interested in learning more about how to
measure for and install drawer slides, I have a really detailed guide that I'll link in the
description. Speaking of drawers, once these cabinets were installed, I pulled out another
sheet of plywood to start cutting down for the drawer boxes. I ripped a few strips, 10 inches
wide for the deeper bottom drawers and 4 inches wide for the shallow top drawers. Then I cut these
to length on the miter saw. You can build drawers a million ways, but I usually cut dados in mine
to install quarter-inch plywood bottoms into. I cut these dados on the table saw just using a
regular blade and adjusting the rip fence to make multiple passes until I had a cut a quarter-inch
wide. You can find all the specifics plus some helpful tips for drawer building in the guide
that I linked in the description. Then I drilled pocket holes into the ends of the front and back
pieces of the drawer boxes. So I drilled all of these and realized that I drilled them into the
wrong board. So these are actually the sides of the drawers, so the slides will mount right here.
So I may be able to cover up one of the pocket holes or like two with the slide, but I'm still
going to see these pocket holes. And if this was a furniture piece, I would recut all these,
but since this is from the shop, I'm just going to leave them. Maybe measure before you drill your
pocket holes and make sure you're drilling them into the front and the back pieces of the drawer
and not the side pieces. Once the pocket holes were drilled, I assembled each drawer box using
pocket hole screws, adding a quarter-inch plywood bottom into the dados. I installed these into the
cabinets using some scrap wood spacer blocks to evenly space them out. Again, that's all covered
in detail in the guide linked below. Once the drawers were installed, I went back and drilled
shelf pin holes to be able to install the shelves in the rest of the cabinets. I used my Kreg shelf
pin jig to drill these holes. And could I have drilled these earlier in the building process?
Yes. Should I have? Probably. But as long as they were added at some point, it's not that big of a
deal. I drilled holes along each side of the cabinets where I might want to add shelves later
and then I could finish things up here by adding the doors. Now I had already cut and painted the
doors for the pantry, but for these base cabinets, I used some two foot by four foot hickory plywood
panels. I took them out of the box and kind of arranged them the way that I wanted. Then I cut
them to the right heights to fit the cabinets. I only had to cut the length here since I made these
cabinets to fit the width already. Now typically with drawer fronts, you run the grain horizontally,
but in this case, I ran it vertically. So for my drawer fronts, I cut the panel to the same height
as I cut the rest of the doors. Then I just measured and marked out the drawer fronts and
cut those. So that way when they go in place, the grain matches and it all runs vertically to match
the doors. I just thought this was a neat design element. You can run the grain and cut them however
you wish. I edge banded all of these doors and drawer fronts and full disclosure, I ran out of
hickory edge banding and couldn't find any more. So I just used birch edge banding. The color actually
wasn't that far off. Once everything was edge banded and sanded well, I used a Kreg concealed
hinge jig to drill holes for the concealed hinges in all the doors. I made these doors full overlay,
so I used full overlay hinges for frameless cabinets to install them into each cabinet.
I have a separate video and a step-by-step tutorial for how to install and adjust these
that I'll link in the description. I screwed all four hickory doors into the cabinets,
then worked on the drawer fronts. I positioned the fronts onto the drawers and just used some
screws from the inside to secure them. I left just enough room between them so that they wouldn't rub
and I centered them side to side. For the large pantry doors, I used three hinges instead of just
two since they are a little heavy. However, since the shelf was in the center of the cabinet, I made
sure to place the middle hinge slightly off-center so that it wouldn't interfere. I used my foot to
hold the door up while I screwed the hinges into the cabinet and for safety reasons, I'm not showing
screwing in the top hinge because I used a swivel chair to reach it. But once all three hinges were
screwed in, I adjusted as needed for the door to open and close easily. One of the last pieces is
adding the toe kick boards. I just cut some three and a half inch wide plywood strips for this,
but you could also use one by fours if you wanted. I just cut these to length and nailed them in
place along the fronts of the bottom of the cabinet. I used one solid piece across the three
base cabinets on each side, but since the pantry cabinets were one inch deeper, I cut a separate
piece for them. Now the last piece of this entire cabinet build was the countertop. You can use
whatever you want for your countertop, but I cut another sheet of plywood into two 24 inch wide
strips. Since this is obviously longer than eight foot, I'm going to have to piece this together.
Now if I just like divided it in two, the seam would be here in the center and that would be fine
if I wanted to put a support piece underneath here, but I don't really want to do that.
Also this is going to be like where I would put my desk up to and so I really wouldn't want the
seam right there just in case it was like a little uneven or whatever. So I'm going to put my eight
foot long piece. I'm going to center it here and then I'm going to cut two pieces to fit on each
side of it. I edge banded and installed the middle eight foot piece first. I got it fairly centered
on the base cabinets and used some one and a quarter inch screws through the top supports
in each cabinet to secure it. I put screws in both the front and the back supports.
Then I measured and cut two shorter sides to finish up the countertop.
Before giving the base cabinets a few coats of poly, I went back and cut a couple pieces to put
along the bottom of the inside of the cabinets. Because I had to shim these up so much from the
unlevel floor, the gap was just kind of ugly so I just put a piece here to hide it.
I gave the cabinet doors a few coats of poly on both the inside and the outside,
then installed some modern black hardware and they were ready to fill up.
Full disclosure, I need to sit down and decide how I want to organize these so I only added
a shelf in one cabinet so far, but that's the beauty of shelf pins. I can install them later
whenever I want. So for now I just shove my unpacked boxes in here and I'll situate it all as I go.
I'm so excited to have this project complete and I just love how much storage and function
that it adds to my workspace. I'm really glad to have some cabinets to keep some of my stuff
free from dust and to keep my workspace just less visually cluttered. I've got some ideas for the
rest of this wall but I'm still contemplating what exactly I want to do with it so stay tuned
to see if I ever make up my mind. I hope you guys enjoyed this video and this project and if you
can't wait to see what's next be sure to subscribe if you aren't already.
Thanks so much for watching friends and until next time, happy building!
